Elisabeth Maria Beunder
Elisabeth Maria Beunder has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Frank Nicolaas Hermanus Schrama
Department of Materials Science and Engineering Delft University of Technology Faculty 3mE Building 34 Mekelweg 2 Delft 2628 CD The Netherlands
7 shared publications - Rob Boom
Department of Materials Science and Engineering Delft University of Technology Faculty 3mE Building 34 Mekelweg 2 Delft 2628 CD The Netherlands
7 shared publications - Yongxiang Yang
Department of Materials Science and Engineering, Delft University of Technology, Delft, The Netherlands
7 shared publications - Jilt Sietsma
Department of Materials Science and Engineering, Delft University of Technology, Delft, Netherlands
6 shared publications Hessel-Jan Visser
Tata Steel, IJmuiden, Netherlands
3 shared publications- Adam Hunt
Materials Processing Institute
2 shared publications
Latest Publications
- 1 August 2022
- Published by Wiley in Steel Research International
- Vol. 93 (8)
Desulfurization of High‐Sulfur HIsarna Hot Metal
- 1 August 2022
- Published by Wiley in Steel Research International
- Vol. 93 (8)
Desulfurization of High‐Sulfur HIsarna Hot Metal
- Open Access
- 10 December 2021
- Published by Wiley in Steel Research International
- Vol. 93 (8) , 2100398
Desulfurization of High‐Sulfur HIsarna Hot Metal
The HIsarna process is one of the emerging low‐CO2 ironmaking processes that could help the steel industry in achieving their carbon footprint goals. HIsarna hot metal contains 3–4 times more sulfur than hot metal from blast furnaces (BFs). Therefore, a literature study, a thermodynamic analysis, and plant data analysis from Tata Steel, IJmuiden, are used herein to investigate the consequences of HIsarna hot metal for the current hot metal desulfurization process. Although the high sulfur concentration and low temperature of HIsarna hot metal lead to a higher total reagent consumption, compared with desulfurization of BF hot metal, the specific magnesium consumption decreases. The higher oxygen concentration in HIsarna hot metal only leads to a small increase in reagent consumption.
- 10 December 2021
- Published by Wiley in Steel Research International
- Vol. 93 (8) , 2100398
Open AccessDesulfurization of High‐Sulfur HIsarna Hot Metal
The HIsarna process is one of the emerging low‐CO2 ironmaking processes that could help the steel industry in achieving their carbon footprint goals. HIsarna hot metal contains 3–4 times more sulfur than hot metal from blast furnaces (BFs). Therefore, a literature study, a thermodynamic analysis, and plant data analysis from Tata Steel, IJmuiden, are used herein to investigate the consequences of HIsarna hot metal for the current hot metal desulfurization process. Although the high sulfur concentration and low temperature of HIsarna hot metal lead to a higher total reagent consumption, compared with desulfurization of BF hot metal, the specific magnesium consumption decreases. The higher oxygen concentration in HIsarna hot metal only leads to a small increase in reagent consumption.
- Open Access
- 2 January 2021
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 48 (1) , 1-13
Optimal hot metal desulphurisation slag considering iron loss and sulphur removal capacity part I: fundamentals
In hot metal desulphurisation (HMD) the slag will hold the removed sulphur. However, the iron that is lost when the slag is skimmed off, accounts for the highest costs of the HMD process. These iron losses are lower when the slag has a lower viscosity, which can be achieved by changing the slag composition. A lower slag basicity decreases the viscosity of the slag, but also lowers its sulphur removal capacity, therefore optimisation is necessary. In this study, the optimal HMD slag composition is investigated, considering both the sulphur removal capacity and the iron losses. In part I the theory is discussed and in part II the optimal slag is validated with plant data, laboratory experiments and a thermodynamic analysis.
- 2 January 2021
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 48 (1) , 1-13
Open AccessOptimal hot metal desulphurisation slag considering iron loss and sulphur removal capacity part I: fundamentals
In hot metal desulphurisation (HMD) the slag will hold the removed sulphur. However, the iron that is lost when the slag is skimmed off, accounts for the highest costs of the HMD process. These iron losses are lower when the slag has a lower viscosity, which can be achieved by changing the slag composition. A lower slag basicity decreases the viscosity of the slag, but also lowers its sulphur removal capacity, therefore optimisation is necessary. In this study, the optimal HMD slag composition is investigated, considering both the sulphur removal capacity and the iron losses. In part I the theory is discussed and in part II the optimal slag is validated with plant data, laboratory experiments and a thermodynamic analysis.
- Open Access
- 1 January 2021
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 48 (1) , 14-24
Optimal hot metal desulphurisation slag considering iron loss and sulphur removal capacity part II: evaluation
The optimal hot metal desulphurisation (HMD) slag is defined as a slag with a sufficient sulphur removal capacity and a low apparent viscosity ( η slag ) which leads to low iron losses. In part I of this study, the fundamentals behind the optimal slag were discussed. In this part these fundamentals are explored by a Monte Carlo simulation, based on FactSage calculations, plant data analysis and melting point and viscosity measurements of the optimal slag. Furthermore, the applicability of knowing the optimal slag composition for an industrial HMD is discussed.
- 1 January 2021
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 48 (1) , 14-24
Open AccessOptimal hot metal desulphurisation slag considering iron loss and sulphur removal capacity part II: evaluation
The optimal hot metal desulphurisation (HMD) slag is defined as a slag with a sufficient sulphur removal capacity and a low apparent viscosity ( η slag ) which leads to low iron losses. In part I of this study, the fundamentals behind the optimal slag were discussed. In this part these fundamentals are explored by a Monte Carlo simulation, based on FactSage calculations, plant data analysis and melting point and viscosity measurements of the optimal slag. Furthermore, the applicability of knowing the optimal slag composition for an industrial HMD is discussed.
- Open Access
- 9 April 2020
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 47 (5) , 464-472
Lowering iron losses during slag removal in hot metal desulphurisation without using fluoride
To lower the iron losses of the hot metal desulphurisation (HMD) process, slag modifiers can be added to the slag. Slag modifiers decrease the apparent viscosity of the HMD slag. Most common slag modifiers in industry contain fluoride as a fluidiser. However, fluoride leads to a higher magnesium consumption and has health, safety and environment issues. Fluoride-free alternatives like nepheline syenite (NS) and fly ash (or pulverised fuel ash, PFA) can decrease the slag’s apparent viscosity. Experiments with HMD slags containing CaF2, NS and PFA and without slag modifier were performed for slags with a high and an average basicity. The melting points of the slags and their viscosities 1250–1600°C were measured. The experimental results are compared with FactSage calculations. PFA and NS are viable alternatives in the industrial HMD process, as reasonable amounts are sufficient to reach the same lower apparent viscosities and melting points as with CaF2.
- 9 April 2020
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 47 (5) , 464-472
Open AccessLowering iron losses during slag removal in hot metal desulphurisation without using fluoride
To lower the iron losses of the hot metal desulphurisation (HMD) process, slag modifiers can be added to the slag. Slag modifiers decrease the apparent viscosity of the HMD slag. Most common slag modifiers in industry contain fluoride as a fluidiser. However, fluoride leads to a higher magnesium consumption and has health, safety and environment issues. Fluoride-free alternatives like nepheline syenite (NS) and fly ash (or pulverised fuel ash, PFA) can decrease the slag’s apparent viscosity. Experiments with HMD slags containing CaF2, NS and PFA and without slag modifier were performed for slags with a high and an average basicity. The melting points of the slags and their viscosities 1250–1600°C were measured. The experimental results are compared with FactSage calculations. PFA and NS are viable alternatives in the industrial HMD process, as reasonable amounts are sufficient to reach the same lower apparent viscosities and melting points as with CaF2.
- Open Access
- 8 November 2019
- Published by Wiley in Steel Research International
- Vol. 91 (11)
The Hampering Effect of Precipitated Carbon on Hot Metal Desulfurization with Magnesium
Carbon may precipitate during the hot metal desulfurization (HMD) process as a result of carbon oversaturation because of temperature decrease. The precipitated carbon flakes form a layer between hot metal and slag. It is postulated that this carbon layer hampers desulfurization with magnesium by preventing MgS particles from reaching the slag phase. At Tata Steel in IJmuiden, the Netherlands, carbon in hot metal is measured in 657 heats after reagent injection. With this data, it can be determined whether the hampering effect of precipitated carbon on MgS flotation has a significant effect on the performance of the industrial HMD process. Plant data show a correlation between the precipitated carbon and the specific magnesium consumption for hot metal with a low initial sulfur concentration (below 225 ppm). This correlation cannot be found for hot metal with a higher initial sulfur concentration (above 275 ppm). Furthermore, a sulfur mass balance is made over the converter process, that shows no effect of carbon precipitation during HMD on resulfurization in the converter. The limited experimental accuracy of the plant data prevents a quantitative description of the hampering effect. The measurements do suggest that the effect is small.
- 8 November 2019
- Published by Wiley in Steel Research International
- Vol. 91 (11)
Open AccessThe Hampering Effect of Precipitated Carbon on Hot Metal Desulfurization with Magnesium
Carbon may precipitate during the hot metal desulfurization (HMD) process as a result of carbon oversaturation because of temperature decrease. The precipitated carbon flakes form a layer between hot metal and slag. It is postulated that this carbon layer hampers desulfurization with magnesium by preventing MgS particles from reaching the slag phase. At Tata Steel in IJmuiden, the Netherlands, carbon in hot metal is measured in 657 heats after reagent injection. With this data, it can be determined whether the hampering effect of precipitated carbon on MgS flotation has a significant effect on the performance of the industrial HMD process. Plant data show a correlation between the precipitated carbon and the specific magnesium consumption for hot metal with a low initial sulfur concentration (below 225 ppm). This correlation cannot be found for hot metal with a higher initial sulfur concentration (above 275 ppm). Furthermore, a sulfur mass balance is made over the converter process, that shows no effect of carbon precipitation during HMD on resulfurization in the converter. The limited experimental accuracy of the plant data prevents a quantitative description of the hampering effect. The measurements do suggest that the effect is small.
- Open Access
- 22 March 2017
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 44 (5) , 333-343
Sulphur removal in ironmaking and oxygen steelmaking
Sulphur removal in the ironmaking and oxygen steelmaking process is reviewed. A sulphur balance is made for the steelmaking process of Tata Steel IJmuiden, the Netherlands. There are four stages where sulphur can be removed: in the blast furnace (BF), during hot metal (HM) pretreatment, in the converter and during the secondary metallurgy (SM) treatment. For sulphur removal a low oxygen activity and a basic slag are required. In the BF typically 90% of the sulphur is removed; still, the HM contains about 0.03% of sulphur. Different HM desulphurisation processes are used worldwide. With co-injection or the Kanbara reactor, sulphur concentrations below 0.001% are reached. Basic slag helps desulphurisation in the converter. However, sulphur increase is not uncommon in the converter due to high oxygen activity and sulphur input via scrap and additions. For low sulphur concentrations SM desulphurisation, with a decreased oxygen activity and a basic slag, is always required.
- 22 March 2017
- Published by SAGE Publications in Ironmaking & Steelmaking: Processes, Products and Applications
- Vol. 44 (5) , 333-343
Open AccessSulphur removal in ironmaking and oxygen steelmaking
Sulphur removal in the ironmaking and oxygen steelmaking process is reviewed. A sulphur balance is made for the steelmaking process of Tata Steel IJmuiden, the Netherlands. There are four stages where sulphur can be removed: in the blast furnace (BF), during hot metal (HM) pretreatment, in the converter and during the secondary metallurgy (SM) treatment. For sulphur removal a low oxygen activity and a basic slag are required. In the BF typically 90% of the sulphur is removed; still, the HM contains about 0.03% of sulphur. Different HM desulphurisation processes are used worldwide. With co-injection or the Kanbara reactor, sulphur concentrations below 0.001% are reached. Basic slag helps desulphurisation in the converter. However, sulphur increase is not uncommon in the converter due to high oxygen activity and sulphur input via scrap and additions. For low sulphur concentrations SM desulphurisation, with a decreased oxygen activity and a basic slag, is always required.
- 1 March 2003
- Published by Wiley in Journal of Applied Mechanics
- Vol. 70 (2) , 275-280
The Motion of a Rolling Polygon
Galileo was the first to analyze the motion of spheres rolling down an inclined surface. Since then, Coulomb’s law of dry friction has covered the case of sliding particles. However, a particle that is not round can still roll, although in a way that is essentially different from the motion studied by Galileo. Instead of keeping contact with the surface, such particles will start bouncing after reaching a certain angular velocity. This motion is a combination of flying and colliding. It is shown that the acceleration of a bouncing particle is always bounded by the accelerations for perfect rolling and sliding. In order to describe the motion of a not perfectly round particle, the polygon is used as a model. The aim of the model is to predict the trajectories of particles that cannot be covered by the models for perfect rolling and sliding.
- 1 March 2003
- Published by Wiley in Journal of Applied Mechanics
- Vol. 70 (2) , 275-280
The Motion of a Rolling Polygon
Galileo was the first to analyze the motion of spheres rolling down an inclined surface. Since then, Coulomb’s law of dry friction has covered the case of sliding particles. However, a particle that is not round can still roll, although in a way that is essentially different from the motion studied by Galileo. Instead of keeping contact with the surface, such particles will start bouncing after reaching a certain angular velocity. This motion is a combination of flying and colliding. It is shown that the acceleration of a bouncing particle is always bounded by the accelerations for perfect rolling and sliding. In order to describe the motion of a not perfectly round particle, the polygon is used as a model. The aim of the model is to predict the trajectories of particles that cannot be covered by the models for perfect rolling and sliding.
- 20 May 2002
- Published by Elsevier in International Journal of Mineral Processing
- Vol. 67 (1-4) , 145-160
Shape separation on a rotating cone
- 20 May 2002
- Published by Elsevier in International Journal of Mineral Processing
- Vol. 67 (1-4) , 145-160
Shape separation on a rotating cone
- 1 July 1999
- Published by Elsevier in International Journal of Mineral Processing
- Vol. 57 (1) , 73-81
Screening kinetics of cylindrical particles
- 1 July 1999
- Published by Elsevier in International Journal of Mineral Processing
- Vol. 57 (1) , 73-81
Screening kinetics of cylindrical particles