Khaled Habib
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Khaled Habib has a total of 66 co-authors. Here are the top co-authors by number of shared publications:
F. Al-Sabti
KISR
9 shared publicationsC. Wu
6 shared publicationsK. Moore
University of Iowa
6 shared publicationsA. Husain
Materials Science and Photo-Electronics Laboratory, Innovative Resources Energy (IRE) Program, Energy and Building Research (EBR) Center, KISR, P.O. Box 24885 SAFAT, Kuwait 13109, Kuwait
4 shared publicationsK. Al-Muhanna
Kuwait Institute for Scientific Research (KISR)
4 shared publicationsV. Eling
4 shared publications
Latest Publications
- Open Access
- 1 March 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (3) , 035035
Representation of effective facial mask design as a novel dimensionless number—Implications for COVID 19 pandemic
A dimensionless number Nr for the effective design of facial masks was derived and compared with other dimensionless numbers of fluid mechanics. Nr is found to closely resemble Euler’s number (Eu). Nr is equal to the logarithmic function of the ratio of inertial force (Fi) of the air to the pressure force (Fp) of the air through the porous membrane of the mask. Nr is then introduced as a novel dimensionless number (Habib number) Ha in which the air flow through a facial mask is derived with parameters for an effective barrier from the COVID-19 virus (SARS COV 2). The introduction of Ha was not only for a comparison reason with other dimensionless numbers of fluid mechanics but also the number Ha is an essential extension of an early work on “Fluid mechanics of facial masks as personal protection equipment (PPE) of COVID-19 virus” [Rev. Sci. Instrum. 92, 074101 (2021)], in which the air flow through the mask is in its optimum design conditions to shield against the COVID-19 virus. As a result, an optimum Nr of expressing the flow of the O2 and N2 gases through the porous membrane was determined (Nr = = = Ha = −4.4). This was obtained when the N95 mask with specifications of a = 20 nm, l = 30 µm, and ε = 30% was used, with respect to the pressure gradient of the human lungs during exhaled and inhaled conditions, PAverage = 20 mm Hg (g cm−1 S−2), and to the size of the COVID-19 virus of about 125 nm (0.125 µm). In addition, a range of values of Nr was analyzed with respect to the optimum (Ha) value of Nr. On the one hand, when the range value of Nr falls between 0 ≥ Nr ≥ Ha, the mask has less resistance than Nr < −4.4, but not necessarily its optimum design conditions. On the other hand, when Nr = 0, the flow through the mask has no resistance at all, as if the mask does not exist.- 1 March 2023
- Published by AIP Publishing in AIP Advances
- Vol. 13 (3) , 035035
Open AccessRepresentation of effective facial mask design as a novel dimensionless number—Implications for COVID 19 pandemic
A dimensionless number Nr for the effective design of facial masks was derived and compared with other dimensionless numbers of fluid mechanics. Nr is found to closely resemble Euler’s number (Eu). Nr is equal to the logarithmic function of the ratio of inertial force (Fi) of the air to the pressure force (Fp) of the air through the porous membrane of the mask. Nr is then introduced as a novel dimensionless number (Habib number) Ha in which the air flow through a facial mask is derived with parameters for an effective barrier from the COVID-19 virus (SARS COV 2). The introduction of Ha was not only for a comparison reason with other dimensionless numbers of fluid mechanics but also the number Ha is an essential extension of an early work on “Fluid mechanics of facial masks as personal protection equipment (PPE) of COVID-19 virus” [Rev. Sci. Instrum. 92, 074101 (2021)], in which the air flow through the mask is in its optimum design conditions to shield against the COVID-19 virus. As a result, an optimum Nr of expressing the flow of the O2 and N2 gases through the porous membrane was determined (Nr = = = Ha = −4.4). This was obtained when the N95 mask with specifications of a = 20 nm, l = 30 µm, and ε = 30% was used, with respect to the pressure gradient of the human lungs during exhaled and inhaled conditions, PAverage = 20 mm Hg (g cm−1 S−2), and to the size of the COVID-19 virus of about 125 nm (0.125 µm). In addition, a range of values of Nr was analyzed with respect to the optimum (Ha) value of Nr. On the one hand, when the range value of Nr falls between 0 ≥ Nr ≥ Ha, the mask has less resistance than Nr < −4.4, but not necessarily its optimum design conditions. On the other hand, when Nr = 0, the flow through the mask has no resistance at all, as if the mask does not exist. - 1 February 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (2) , 029901
Erratum: “Fluid mechanics of facial masks as personal protection equipment (PPE) of COVID-19 virus” [Rev. Sci. Instrum. 92, 074101 (2021)]
- 1 February 2023
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 94 (2) , 029901
Erratum: “Fluid mechanics of facial masks as personal protection equipment (PPE) of COVID-19 virus” [Rev. Sci. Instrum. 92, 074101 (2021)]
- 1 July 2021
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 92 (7) , 074101
Fluid mechanics of facial masks as personal protection equipment (PPE) of COVID-19 virus
A fluid mechanics model of inhaled air gases, nitrogen (N2) and oxygen (O2) gases, and exhaled gas components (CO2 and water vapor particles) through a facial mask (membrane) to shield the COVID-19 virus is established. The model was developed based on several gas flux contributions that normally take place through membranes. Semiempirical solutions of the mathematical model were predicted for the N95 facial mask accounting on several parameters, such as a range of porosity size (i.e., 1–30 nm), void fraction (i.e., 10−3%–0.3%), and thickness of the membrane (i.e., 10–40 µm) in comparison to the size of the COVID-19 virus. A unitless number (Nr) was introduced for the first time to describe semiempirical solutions of O2, N2, and CO2 gases through the porous membrane. An optimum Nr of expressing the flow of the inhaled air gases, O2 and N2, through the porous membrane was determined (NO2 = NN2 = −4.4) when an N95 facial mask of specifications of a = 20 nm, l = 30 µm, and ε = 30% was used as a personal protection equipment (PPE). The concept of the optimum number Nr can be standardized not only for testing commercially available facial masks as PPEs but also for designing new masks for protecting humans from the COVID-19 virus.
- 1 July 2021
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 92 (7) , 074101
Fluid mechanics of facial masks as personal protection equipment (PPE) of COVID-19 virus
A fluid mechanics model of inhaled air gases, nitrogen (N2) and oxygen (O2) gases, and exhaled gas components (CO2 and water vapor particles) through a facial mask (membrane) to shield the COVID-19 virus is established. The model was developed based on several gas flux contributions that normally take place through membranes. Semiempirical solutions of the mathematical model were predicted for the N95 facial mask accounting on several parameters, such as a range of porosity size (i.e., 1–30 nm), void fraction (i.e., 10−3%–0.3%), and thickness of the membrane (i.e., 10–40 µm) in comparison to the size of the COVID-19 virus. A unitless number (Nr) was introduced for the first time to describe semiempirical solutions of O2, N2, and CO2 gases through the porous membrane. An optimum Nr of expressing the flow of the inhaled air gases, O2 and N2, through the porous membrane was determined (NO2 = NN2 = −4.4) when an N95 facial mask of specifications of a = 20 nm, l = 30 µm, and ε = 30% was used as a personal protection equipment (PPE). The concept of the optimum number Nr can be standardized not only for testing commercially available facial masks as PPEs but also for designing new masks for protecting humans from the COVID-19 virus.
- 1 January 2021
- Published by Springer Nature in Optical Review
- Vol. 28 (1) , 18-26
Electrochemical parameters of aluminum oxide film in situ during anodization of aluminum by white light-optical interferometry
- 1 January 2021
- Published by Springer Nature in Optical Review
- Vol. 28 (1) , 18-26
Electrochemical parameters of aluminum oxide film in situ during anodization of aluminum by white light-optical interferometry
- Open Access
- 1 December 2017
- Published by Springer Nature in Journal of Saudi Chemical Society
- Vol. 21 (8) , 938-942
Measurement of aluminum oxide film by Fabry–Pérot interferometry and scanning electron microscopy
- 1 December 2017
- Published by Springer Nature in Journal of Saudi Chemical Society
- Vol. 21 (8) , 938-942
Open AccessMeasurement of aluminum oxide film by Fabry–Pérot interferometry and scanning electron microscopy
- 1 March 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 4 (3) , 035201
Energy efficiency of iron–boron–silicon metallic glasses in sulfuric acid solutions
A criterion of the energy efficiency of iron-boron-silicon metallic glasses in sulfuric acid solutions is proposed for the first time. The criterion has been derived based on calculating the limit of the ratio value of the conductivity of a metallic glass in aqueous solution to the conductivity of the metallic glass in air. In other words, the conductivity ratio of a metallic glass in aqueous solution to the conductivity of the metallic glass in air =1, was applied to determine the energy efficiency of the metallic glass in the aqueous solution when the conductivity of a metallic glass in air became equal (decreased) to the steady conductivity of the metallic glass in aqueous solution as a function of time of the exposure of the metallic glass to the aqueous solution. This criterion was not only used to determine the energy efficiency of different metallic glasses, but also, the criterion was used to determine the energy efficiency of metallic glasses exposed to a wide range of sulfuric acid concentrations. These conductivity values were determined by the electrochemical impedance spectroscopy (EIS). In addition, the criterion can be applied under diverse test conditions with a predetermined period of the operational life of the metallic glasses as functional materials. Furthermore, variations of the energy efficiency of the metallic glasses as a function of the acid concentration and time were produced by fitting the experimental data to a numerical model using a nonlinear regression method. The profiles of the metallic glasses exhibit a less conservative behavior of the energy efficiency than the proposed analytical criterion.
- 1 March 2017
- Published by IOP Publishing in Materials Research Express
- Vol. 4 (3) , 035201
Energy efficiency of iron–boron–silicon metallic glasses in sulfuric acid solutions
A criterion of the energy efficiency of iron-boron-silicon metallic glasses in sulfuric acid solutions is proposed for the first time. The criterion has been derived based on calculating the limit of the ratio value of the conductivity of a metallic glass in aqueous solution to the conductivity of the metallic glass in air. In other words, the conductivity ratio of a metallic glass in aqueous solution to the conductivity of the metallic glass in air =1, was applied to determine the energy efficiency of the metallic glass in the aqueous solution when the conductivity of a metallic glass in air became equal (decreased) to the steady conductivity of the metallic glass in aqueous solution as a function of time of the exposure of the metallic glass to the aqueous solution. This criterion was not only used to determine the energy efficiency of different metallic glasses, but also, the criterion was used to determine the energy efficiency of metallic glasses exposed to a wide range of sulfuric acid concentrations. These conductivity values were determined by the electrochemical impedance spectroscopy (EIS). In addition, the criterion can be applied under diverse test conditions with a predetermined period of the operational life of the metallic glasses as functional materials. Furthermore, variations of the energy efficiency of the metallic glasses as a function of the acid concentration and time were produced by fitting the experimental data to a numerical model using a nonlinear regression method. The profiles of the metallic glasses exhibit a less conservative behavior of the energy efficiency than the proposed analytical criterion.
- Open Access
- 1 September 2016
- Published by Springer Nature in Journal of Saudi Chemical Society
- Vol. 20, S541-S546
Surface resistivity/conductivity of oxide–hydroxide compounds in inhibited seawater by optical interferometry
- 1 September 2016
- Published by Springer Nature in Journal of Saudi Chemical Society
- Vol. 20, S541-S546
Open AccessSurface resistivity/conductivity of oxide–hydroxide compounds in inhibited seawater by optical interferometry
- Open Access
- 1 July 2016
- Published by Springer Nature in Journal of Saudi Chemical Society
- Vol. 20 (4) , 391-396
Marine bio-fouling of different alloys exposed to continuous flowing fresh seawater by electrochemical impedance spectroscopy
- 1 July 2016
- Published by Springer Nature in Journal of Saudi Chemical Society
- Vol. 20 (4) , 391-396
Open AccessMarine bio-fouling of different alloys exposed to continuous flowing fresh seawater by electrochemical impedance spectroscopy
- 1 March 2016
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 87 (3) , 034102
Opto-electrochemical spectroscopy of metals in aqueous solutions
In the present investigation, holographic interferometry was utilized for the first time to determine the rate change of the electrical resistance of aluminium samples during the initial stage of anodisation processes in aqueous solution. In fact, because the resistance values in this investigation were obtained by holographic interferometry, electromagnetic method rather than electronic method, the abrupt rate change of the resistance was called electrical resistance–emission spectroscopy. The anodisation process of the aluminium samples was carried out by electrochemical impedance spectroscopy (EIS) in different sulphuric acid concentrations (1.0%–2.5% H2SO4) at room temperature. In the meantime, the real time holographic interferometry was used to determine the difference between the electrical resistance of two subsequent values, dR, as a function of the elapsed time of the EIS experiment for the aluminium samples in 1.0%, 1.5%, 2.0%, and 2.5% H2SO4 solutions. The electrical resistance–emission spectra of the present investigation represent a detailed picture of not only the rate change of the electrical resistance throughout the anodisation processes but also the spectra represent the rate change of the growth of the oxide films on the aluminium samples in different solutions. As a result, a new spectrometer was developed based on the combination of the holographic interferometry and electrochemical impedance spectroscopy for studying in situ the electrochemical behavior of metals in aqueous solutions.
- 1 March 2016
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 87 (3) , 034102
Opto-electrochemical spectroscopy of metals in aqueous solutions
In the present investigation, holographic interferometry was utilized for the first time to determine the rate change of the electrical resistance of aluminium samples during the initial stage of anodisation processes in aqueous solution. In fact, because the resistance values in this investigation were obtained by holographic interferometry, electromagnetic method rather than electronic method, the abrupt rate change of the resistance was called electrical resistance–emission spectroscopy. The anodisation process of the aluminium samples was carried out by electrochemical impedance spectroscopy (EIS) in different sulphuric acid concentrations (1.0%–2.5% H2SO4) at room temperature. In the meantime, the real time holographic interferometry was used to determine the difference between the electrical resistance of two subsequent values, dR, as a function of the elapsed time of the EIS experiment for the aluminium samples in 1.0%, 1.5%, 2.0%, and 2.5% H2SO4 solutions. The electrical resistance–emission spectra of the present investigation represent a detailed picture of not only the rate change of the electrical resistance throughout the anodisation processes but also the spectra represent the rate change of the growth of the oxide films on the aluminium samples in different solutions. As a result, a new spectrometer was developed based on the combination of the holographic interferometry and electrochemical impedance spectroscopy for studying in situ the electrochemical behavior of metals in aqueous solutions.
- 1 December 2015
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 86 (12) , 124101
Degradation/oxidation susceptibility of organic photovoltaic cells in aqueous solutions
A criterion of the degradation/oxidation susceptibility of organic photovoltaic (OPV) cells in aqueous solutions was proposed for the first time. The criterion was derived based on calculating the limit of the ratio value of the polarization resistance of an OPV cell in aqueous solution (Rps) to the polarization resistance of the OPV cell in air (Rpair). In other words, the criterion lim(Rps/Rpair) = 1 was applied to determine the degradation/oxidation of the OPV cell in the aqueous solution when Rpair became equal (increased) to Rps as a function of time of the exposure of the OPV cell to the aqueous solution. This criterion was not only used to determine the degradation/oxidation of different OPV cells in a simulated operational environment but also it was used to determine the electrochemical behavior of OPV cells in deionized water and a polluted water with fine particles of sand. The values of Rps were determined by the electrochemical impedance spectroscopy at low frequency. In addition, the criterion can be applied under diverse test conditions with a predetermined period of OPV operations.
- 1 December 2015
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 86 (12) , 124101
Degradation/oxidation susceptibility of organic photovoltaic cells in aqueous solutions
A criterion of the degradation/oxidation susceptibility of organic photovoltaic (OPV) cells in aqueous solutions was proposed for the first time. The criterion was derived based on calculating the limit of the ratio value of the polarization resistance of an OPV cell in aqueous solution (Rps) to the polarization resistance of the OPV cell in air (Rpair). In other words, the criterion lim(Rps/Rpair) = 1 was applied to determine the degradation/oxidation of the OPV cell in the aqueous solution when Rpair became equal (increased) to Rps as a function of time of the exposure of the OPV cell to the aqueous solution. This criterion was not only used to determine the degradation/oxidation of different OPV cells in a simulated operational environment but also it was used to determine the electrochemical behavior of OPV cells in deionized water and a polluted water with fine particles of sand. The values of Rps were determined by the electrochemical impedance spectroscopy at low frequency. In addition, the criterion can be applied under diverse test conditions with a predetermined period of OPV operations.