Jose Carlos Pedro
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jose Carlos Pedro has a total of 173 co-authors. Here are the top co-authors by number of shared publications:
- Pedro Miguel Cabral
Instituto de Telecomunicaes and DETI, Universidade de Aveiro, Aveiro, Portugal
55 shared publications - Nuno Borges Carvalho
Universidade de Aveiro
50 shared publications - Telmo Reis Cunha
Instituto de Telecomunicaes (IT), Universidade de Aveiro, Campus Universitrio de Santiago, Aveiro, Portugal
38 shared publications - Luis Cotimos Nunes
Instituto de Telecomunicaes and DETI, Universidade de Aveiro, Aveiro, Portugal
34 shared publications - Filipe M. Barradas
Instituto de Telecomunicaes and DETI, Universidade de Aveiro, Aveiro, Portugal
26 shared publications - Jose Angel Garcia
Department of Communications Engineering, University of Cantabria, 39005 Santander, Spain
16 shared publications
Latest Publications
- 17 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. PP (00189480) , 1-15
Concurrent Dual-Band Continuous Class-F Power Amplifier: From Theory to Practice
This article extends the continuous single-tone Class-B/F power amplifier (PA) theory to concurrent dual-band operation. Continuous load impedance design spaces, with constant efficiency and output power under concurrent two-tone excitation, are deduced and analyzed. Contrary to single-tone classes, in concurrent-band operation, the intermodulation frequencies play a central role in the performance, which increases the complexity of the analysis. The proposed method makes use of the notion of envelopes to simplify the problem. Using this notion, the waveform shaping can be applied at both the envelope and/or carrier levels, yielding different operation classes, which are analyzed in this manuscript. Under the proposed methodology, the baseband impedance is a consequence of the designed waveforms, rather than being set at the short-circuit. Similarly, terminations at other intermodulation frequencies also naturally arise under the framework used. The derived impedances for concurrent-band differ from those of traditional single tone, indicating that design methodologies based on frequency-by-frequency are suboptimal. As a proof of concept, a concurrent dual-band Class-F PA operating at 1.8 and 2.15 GHz was designed, implemented, and experimentally validated. The measured output power and efficiency for different tone asymmetries are consistent with the developed theory. Moreover, with the proposed design target impedances, there is no performance degradation under concurrent-band operation when the PA is excited with a modulated signal in each band.
- 17 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. PP (00189480) , 1-15
Concurrent Dual-Band Continuous Class-F Power Amplifier: From Theory to Practice
This article extends the continuous single-tone Class-B/F power amplifier (PA) theory to concurrent dual-band operation. Continuous load impedance design spaces, with constant efficiency and output power under concurrent two-tone excitation, are deduced and analyzed. Contrary to single-tone classes, in concurrent-band operation, the intermodulation frequencies play a central role in the performance, which increases the complexity of the analysis. The proposed method makes use of the notion of envelopes to simplify the problem. Using this notion, the waveform shaping can be applied at both the envelope and/or carrier levels, yielding different operation classes, which are analyzed in this manuscript. Under the proposed methodology, the baseband impedance is a consequence of the designed waveforms, rather than being set at the short-circuit. Similarly, terminations at other intermodulation frequencies also naturally arise under the framework used. The derived impedances for concurrent-band differ from those of traditional single tone, indicating that design methodologies based on frequency-by-frequency are suboptimal. As a proof of concept, a concurrent dual-band Class-F PA operating at 1.8 and 2.15 GHz was designed, implemented, and experimentally validated. The measured output power and efficiency for different tone asymmetries are consistent with the developed theory. Moreover, with the proposed design target impedances, there is no performance degradation under concurrent-band operation when the PA is excited with a modulated signal in each band.
- 6 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (6) , 914-917
Baseband Impedance Design Space for Concurrent-Band PA Operation
Concurrent dual-band power amplifiers (PAs) often experience significant efficiency degradation due to the strong baseband components generated under two-tone excitation. Conventional wisdom dictates that the baseband impedance, in particular at $|\omega _{2}{\,}-{\,}\omega _{1}|$ (IF1), must be short-circuited to avoid bias voltage fluctuation. This letter demonstrates that this assumption might not be the best solution for the output matching. A broader analytical formulation of the device operation shows that, when different fundamental impedances are selected at each operation band, the desired IF1impedance can become either inductive or capacitive. In these cases, shorting the IF1impedance leads to performance degradation of the PA. To demonstrate this effect, a hardware prototype with controllable IF1impedance is designed and evaluated. Measurements confirm that concurrent-mode drain efficiency and output power improve under the analytically derived IF1impedance, in comparison to the short IF1impedance case, validating the developed theory. Additionally, the adjacent channel leakage ratio (ACPR) measurement also demonstrates enhanced linearity when the optimal IF1impedance is applied.
- 6 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 36 (6) , 914-917
Baseband Impedance Design Space for Concurrent-Band PA Operation
Concurrent dual-band power amplifiers (PAs) often experience significant efficiency degradation due to the strong baseband components generated under two-tone excitation. Conventional wisdom dictates that the baseband impedance, in particular at $|\omega _{2}{\,}-{\,}\omega _{1}|$ (IF1), must be short-circuited to avoid bias voltage fluctuation. This letter demonstrates that this assumption might not be the best solution for the output matching. A broader analytical formulation of the device operation shows that, when different fundamental impedances are selected at each operation band, the desired IF1impedance can become either inductive or capacitive. In these cases, shorting the IF1impedance leads to performance degradation of the PA. To demonstrate this effect, a hardware prototype with controllable IF1impedance is designed and evaluated. Measurements confirm that concurrent-mode drain efficiency and output power improve under the analytically derived IF1impedance, in comparison to the short IF1impedance case, validating the developed theory. Additionally, the adjacent channel leakage ratio (ACPR) measurement also demonstrates enhanced linearity when the optimal IF1impedance is applied.
- 22 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. PP (00189480) , 1-14
Losses Behavior Explanation and Its Impact on the Performance of Load-Modulated Power Amplifiers
Efficiency degradation in load-modulated power amplifiers (LMPAs) primarily arises from dissipative losses in the output matching networks (OMNs) or combiners, which vary dynamically throughout the load-modulation (LM) process and depend on the designed output back-off (OBO). This article presents a comprehensive theoretical framework to explain the loss behavior in LMPAs, focusing on the Doherty power amplifier (DPA) and the sequential load-modulated balanced amplifier (SLMBA) as representative examples. The impact of load modulation on lossy OMNs, the contribution of finite off-state impedance of the auxiliary amplifiers, and the effect of main/peaking asymmetry on the global losses are systematically analyzed. Generalized closed-form expressions are derived to quantify the global losses and validated through simulations, providing, for the first time, a unified explanation of the dominant losses behavior in LMPAs and offering guidelines for the design of next-generation high-efficiency base-station power amplifiers (PAs). To validate the application of previously gathered knowledge for achieving high performance at large back-off (BO), a reflective-type DPA (RDPA) was designed, fabricated, and experimentally evaluated. The 2-GHz prototype, designed for an 18-dB OBO, achieved a maximum output power of 52.2 dBm and maintained a drain efficiency (DE) exceeding 50% across a 20-dB OBO range.
- 22 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. PP (00189480) , 1-14
Losses Behavior Explanation and Its Impact on the Performance of Load-Modulated Power Amplifiers
Efficiency degradation in load-modulated power amplifiers (LMPAs) primarily arises from dissipative losses in the output matching networks (OMNs) or combiners, which vary dynamically throughout the load-modulation (LM) process and depend on the designed output back-off (OBO). This article presents a comprehensive theoretical framework to explain the loss behavior in LMPAs, focusing on the Doherty power amplifier (DPA) and the sequential load-modulated balanced amplifier (SLMBA) as representative examples. The impact of load modulation on lossy OMNs, the contribution of finite off-state impedance of the auxiliary amplifiers, and the effect of main/peaking asymmetry on the global losses are systematically analyzed. Generalized closed-form expressions are derived to quantify the global losses and validated through simulations, providing, for the first time, a unified explanation of the dominant losses behavior in LMPAs and offering guidelines for the design of next-generation high-efficiency base-station power amplifiers (PAs). To validate the application of previously gathered knowledge for achieving high performance at large back-off (BO), a reflective-type DPA (RDPA) was designed, fabricated, and experimentally evaluated. The 2-GHz prototype, designed for an 18-dB OBO, achieved a maximum output power of 52.2 dBm and maintained a drain efficiency (DE) exceeding 50% across a 20-dB OBO range.
- Open Access
- 2 January 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (2) , 025112
Exploring surface effects in GaN based nano-diodes: a physical interpretation through Monte Carlo simulations
Surface-trap effects are shown to be of main importance to understand the working principle of a two-terminal device based on AlGaN/GaN nanochannels. A deep knowledge of the physical mechanism governing the behavior of the current flow may allow developing physical models for the surface traps to be implemented in other tools to improve the potential capability of these devices as microwave power detectors. The carrier trapping/de-trapping processes at the boundary surfaces are of special interest, not only because of their influence on the level of the current flowing along the nanochannels, but also because of their impact in the saturation of the I–V curve. In this work, based on Monte Carlo simulations where traps are implemented using two different models, we replicate the experimental behavior of current transients, identify the differences between the surface charge distributions under forward and reverse bias and provide an explanation for the saturation of the I–V curve of the nanochannels.
- 2 January 2026
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 59 (2) , 025112
Open AccessExploring surface effects in GaN based nano-diodes: a physical interpretation through Monte Carlo simulations
Surface-trap effects are shown to be of main importance to understand the working principle of a two-terminal device based on AlGaN/GaN nanochannels. A deep knowledge of the physical mechanism governing the behavior of the current flow may allow developing physical models for the surface traps to be implemented in other tools to improve the potential capability of these devices as microwave power detectors. The carrier trapping/de-trapping processes at the boundary surfaces are of special interest, not only because of their influence on the level of the current flowing along the nanochannels, but also because of their impact in the saturation of the I–V curve. In this work, based on Monte Carlo simulations where traps are implemented using two different models, we replicate the experimental behavior of current transients, identify the differences between the surface charge distributions under forward and reverse bias and provide an explanation for the saturation of the I–V curve of the nanochannels.
- 5 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (1) , 180-194
Optimal Driving Signal Extraction for Maximum Efficiency of Dual-Input High Power Amplifiers
Dual-input single-output (DISO) radio frequency (RF) power amplifiers (PAs) have gathered significant interest for highly efficient amplification of modulated signals. DISO PAs provide advantages over their single-input single-output (SISO) counterparts, both for design and operation. However, contrary to SISO, driving DISO PAs requires an extraction of the optimum driving signals to maximize the power-added efficiency (PAE), and some input conditions can easily make the PA operate in a nonsafe region. This article presents algorithms to safely derive these optimal input signals. Two types of algorithms are proposed, which are dubbed “exploration” and “extraction”; the exploration algorithm finds a safe operation region of the DISO PA from minimal a priori information on the device under test; the extraction algorithm finds the optimal input drive from the exploration algorithm data. These algorithms are tested and validated in simulation and measurement for different DISO PA architectures.
- 5 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (1) , 180-194
Optimal Driving Signal Extraction for Maximum Efficiency of Dual-Input High Power Amplifiers
Dual-input single-output (DISO) radio frequency (RF) power amplifiers (PAs) have gathered significant interest for highly efficient amplification of modulated signals. DISO PAs provide advantages over their single-input single-output (SISO) counterparts, both for design and operation. However, contrary to SISO, driving DISO PAs requires an extraction of the optimum driving signals to maximize the power-added efficiency (PAE), and some input conditions can easily make the PA operate in a nonsafe region. This article presents algorithms to safely derive these optimal input signals. Two types of algorithms are proposed, which are dubbed “exploration” and “extraction”; the exploration algorithm finds a safe operation region of the DISO PA from minimal a priori information on the device under test; the extraction algorithm finds the optimal input drive from the exploration algorithm data. These algorithms are tested and validated in simulation and measurement for different DISO PA architectures.
- 8 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 5607-5608
Guest Editorial Mini-Special Issue on the 2023 International Workshop on Integrated Nonlinear Microwave and Millimetre-Wave Circuits
This Mini-Special Issue of the IEEE Transactions on Microwave Theory and Techniques (TMTT) contains four expanded papers from the 2023 International Workshop on Integrated Nonlinear Microwave and Millimetre- Wave Circuits (INMMiC), which was held in Aveiro, Portugal, from November 8 to 10, 2023. The INMMiC is a forum for promoting, discussing, and spreading ideas in the field of nonlinear microwave and millimeter-wave circuits and systems. The INMMiC Workshop was originally launched in Duisburg, Germany, in 1990, and achieved its present form in Rome, Italy, in 2004, after a dormant period of several years. Subsequently, the INMMiC was held at different venues around Europe, namely: in 2006 in Aveiro, Portugal; 2008 in Málaga, Spain; 2010 in Gothenburg, Sweden; 2011 in Vienna, Austria; 2012 in Dublin, Ireland; 2014 in Leuven, Belgium; 2015 in Taormina, Italy; 2017 in Graz, Austria; 2018 in Brive-La-Gaillarde, France; and in 2022 in Cardiff, the U.K.
- 8 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 5607-5608
Guest Editorial Mini-Special Issue on the 2023 International Workshop on Integrated Nonlinear Microwave and Millimetre-Wave Circuits
This Mini-Special Issue of the IEEE Transactions on Microwave Theory and Techniques (TMTT) contains four expanded papers from the 2023 International Workshop on Integrated Nonlinear Microwave and Millimetre- Wave Circuits (INMMiC), which was held in Aveiro, Portugal, from November 8 to 10, 2023. The INMMiC is a forum for promoting, discussing, and spreading ideas in the field of nonlinear microwave and millimeter-wave circuits and systems. The INMMiC Workshop was originally launched in Duisburg, Germany, in 1990, and achieved its present form in Rome, Italy, in 2004, after a dormant period of several years. Subsequently, the INMMiC was held at different venues around Europe, namely: in 2006 in Aveiro, Portugal; 2008 in Málaga, Spain; 2010 in Gothenburg, Sweden; 2011 in Vienna, Austria; 2012 in Dublin, Ireland; 2014 in Leuven, Belgium; 2015 in Taormina, Italy; 2017 in Graz, Austria; 2018 in Brive-La-Gaillarde, France; and in 2022 in Cardiff, the U.K.
- Open Access
- 4 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 4 (3) , 389-403
The Impact of a Taper Impedance Transformation on the TRL De-Embedding Error
This work originates from the realization that, in a transformed impedance thru-reflect-line (TRL) calibration, the sensitivity to random measurement errors is affected by impedance discrepancies between the impedance transformer and the device-under-test (DUT). Through a thorough exploration that includes theoretical analysis, simulations and TRL measurements, this study establishes that the accuracy of de-embedding operations on a transformed impedance medium is intricately tied to the difference between the Thevenin impedance seen from the DUT-side of the launcher and the DUT impedance. A noteworthy finding is that minimizing this difference enhances the resilience of the de-embedding process against random measurement errors, being advantageous for precision modeling techniques, and demonstrating the importance of considering those concepts when designing an access structure to a DUT.
- 4 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 4 (3) , 389-403
Open AccessThe Impact of a Taper Impedance Transformation on the TRL De-Embedding Error
This work originates from the realization that, in a transformed impedance thru-reflect-line (TRL) calibration, the sensitivity to random measurement errors is affected by impedance discrepancies between the impedance transformer and the device-under-test (DUT). Through a thorough exploration that includes theoretical analysis, simulations and TRL measurements, this study establishes that the accuracy of de-embedding operations on a transformed impedance medium is intricately tied to the difference between the Thevenin impedance seen from the DUT-side of the launcher and the DUT impedance. A noteworthy finding is that minimizing this difference enhances the resilience of the de-embedding process against random measurement errors, being advantageous for precision modeling techniques, and demonstrating the importance of considering those concepts when designing an access structure to a DUT.
- 21 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 5615-5623
A Physics-Based 1-D Equivalent Circuit Model for an AlGaN/GaN HEMT
This work presents a physics-based 1-D equivalent-circuit model (ECM) for an AlGaN/GaN HEMT. For that, it starts with the thorough derivation of an analytical 1-D model from a 2-D drift-diffusion representation of the device in a technology computer-aided design (TCAD) environment. Such a 1-D model describes the potential, charge density, and current density along the 2-DEG channel to allow the computation of the corresponding distributed voltages, currents, and charges (and so, capacitances). These are obtained by discretizing the analytical 1-D model, associating a 4-node sub-circuit to each spatial cell, and deriving a longitudinal branch current and a transversal charge source from these 4-node voltages. The ECM implementation in a time-domain or frequency-domain circuit simulator is very useful for a microwave engineer to understand the device operation and thus extract valuable information for the derivation of accurate lumped ECMs, as well as enabling the relation of the device microwave performance with its internal physical structure. To test the accuracy of the proposed ECM, its current and charge predictions obtained from a commercial circuit simulator are compared with full 2-D TCAD simulations. The 1-D model was further validated by comparing its predictions with the ones obtained from TCAD simulations for different AlGaN barrier thicknesses and gate lengths.
- 21 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 5615-5623
A Physics-Based 1-D Equivalent Circuit Model for an AlGaN/GaN HEMT
This work presents a physics-based 1-D equivalent-circuit model (ECM) for an AlGaN/GaN HEMT. For that, it starts with the thorough derivation of an analytical 1-D model from a 2-D drift-diffusion representation of the device in a technology computer-aided design (TCAD) environment. Such a 1-D model describes the potential, charge density, and current density along the 2-DEG channel to allow the computation of the corresponding distributed voltages, currents, and charges (and so, capacitances). These are obtained by discretizing the analytical 1-D model, associating a 4-node sub-circuit to each spatial cell, and deriving a longitudinal branch current and a transversal charge source from these 4-node voltages. The ECM implementation in a time-domain or frequency-domain circuit simulator is very useful for a microwave engineer to understand the device operation and thus extract valuable information for the derivation of accurate lumped ECMs, as well as enabling the relation of the device microwave performance with its internal physical structure. To test the accuracy of the proposed ECM, its current and charge predictions obtained from a commercial circuit simulator are compared with full 2-D TCAD simulations. The 1-D model was further validated by comparing its predictions with the ones obtained from TCAD simulations for different AlGaN barrier thicknesses and gate lengths.
- 9 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 5609-5614
Influence of Surface States in AlGaN/GaN Nanodiodes Analyzed by Preconditioned Transient Current Measurements
AlGaN/GaN nanodiodes consisting of an array of several nanochannels in parallel are potential candidates for detection in the terahertz (THz) range. The nanochannels are fabricated by etching two isolating trenches and show a current–voltage characteristic strongly influenced by the presence of surface charges at the channel sidewalls. Transient current effects have been characterized at room temperature and found to be associated with electron capture and emission mechanisms by surface traps. The conductance of these devices increases or decreases depending on the history of applied voltage since it changes the occupation of the surface states and thus the depletion region present near the sidewalls. Moreover, the lateral field effect plays an important role, since, in addition to promoting trap charging or discharging, modifies the depletion region around the trenches, both of these processes determine the conductance of the channel. In addition, the increase of the bias induces an effect analog to the drain-induced barrier lowering (DIBL) of FETs. In this article, the static behavior and transients of current of these nanochannels were characterized from the experimental point of view thanks to very short duration voltage pulses, while Monte Carlo (MC) simulations were able to mimic the observed trends providing as well a physical interpretation that the charges trapped at the sidewalls of the trenches of the channels act as the gate in a FET.
- 9 May 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (10) , 5609-5614
Influence of Surface States in AlGaN/GaN Nanodiodes Analyzed by Preconditioned Transient Current Measurements
AlGaN/GaN nanodiodes consisting of an array of several nanochannels in parallel are potential candidates for detection in the terahertz (THz) range. The nanochannels are fabricated by etching two isolating trenches and show a current–voltage characteristic strongly influenced by the presence of surface charges at the channel sidewalls. Transient current effects have been characterized at room temperature and found to be associated with electron capture and emission mechanisms by surface traps. The conductance of these devices increases or decreases depending on the history of applied voltage since it changes the occupation of the surface states and thus the depletion region present near the sidewalls. Moreover, the lateral field effect plays an important role, since, in addition to promoting trap charging or discharging, modifies the depletion region around the trenches, both of these processes determine the conductance of the channel. In addition, the increase of the bias induces an effect analog to the drain-induced barrier lowering (DIBL) of FETs. In this article, the static behavior and transients of current of these nanochannels were characterized from the experimental point of view thanks to very short duration voltage pulses, while Monte Carlo (MC) simulations were able to mimic the observed trends providing as well a physical interpretation that the charges trapped at the sidewalls of the trenches of the channels act as the gate in a FET.
- Open Access
- 18 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 41631-41642
Theory and Design of Doherty Power Amplifier With Active Harmonic Injection
This paper analyzes the performance of the Doherty power amplifier (DPA) with the injection of the second harmonic component generated by the carrier power amplifier (PA) into the peaking PA and vice-versa, using a harmonic injection network (HIN). A mathematical analysis is presented to estimate the second harmonic loads seen by the carrier and peaking PAs in the presence of the HIN. Furthermore, a step-by-step design guide to designing a harmonic injection DPA (HI-DPA) is also presented. It is noted that the passive load provided by the output matching network ( Z ′ c2 and Z ′ p2 ), the electrical length of the HIN (θ inj ), and the phase difference between the currents of the carrier and peaking PAs (θ p ) at the second harmonic are crucial to present an active load to either the carrier or peaking PAs. In the HI-DPA, it is not possible to achieve an active second harmonic load for the carrier and peaking PAs simultaneously. Due to the interaction between the carrier and peaking PAs at the second harmonic, if the carrier PA sees an active load, the peaking PA sees a passive load, and vice-versa. The HI-DPA is designed with the HIN, and its performance is compared with the high-efficiency passive harmonic-tuned DPA. It is demonstrated that both the carrier and peaking PAs cannot see an active impedance at the second harmonic simultaneously. However, it is possible to increase the efficiency in the Doherty load-modulation region with the harmonic injection technique using the HIN. This would be translated into an average efficiency increase when the PA is excited with the modulated signal.
- 18 March 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 41631-41642
Open AccessTheory and Design of Doherty Power Amplifier With Active Harmonic Injection
This paper analyzes the performance of the Doherty power amplifier (DPA) with the injection of the second harmonic component generated by the carrier power amplifier (PA) into the peaking PA and vice-versa, using a harmonic injection network (HIN). A mathematical analysis is presented to estimate the second harmonic loads seen by the carrier and peaking PAs in the presence of the HIN. Furthermore, a step-by-step design guide to designing a harmonic injection DPA (HI-DPA) is also presented. It is noted that the passive load provided by the output matching network ( Z ′ c2 and Z ′ p2 ), the electrical length of the HIN (θ inj ), and the phase difference between the currents of the carrier and peaking PAs (θ p ) at the second harmonic are crucial to present an active load to either the carrier or peaking PAs. In the HI-DPA, it is not possible to achieve an active second harmonic load for the carrier and peaking PAs simultaneously. Due to the interaction between the carrier and peaking PAs at the second harmonic, if the carrier PA sees an active load, the peaking PA sees a passive load, and vice-versa. The HI-DPA is designed with the HIN, and its performance is compared with the high-efficiency passive harmonic-tuned DPA. It is demonstrated that both the carrier and peaking PAs cannot see an active impedance at the second harmonic simultaneously. However, it is possible to increase the efficiency in the Doherty load-modulation region with the harmonic injection technique using the HIN. This would be translated into an average efficiency increase when the PA is excited with the modulated signal.