Malik Shoaib Suleman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Malik Shoaib Suleman has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Kok Keong Lau
Center of Carbon Capture, Utilisation and Storage (CCCUS), Department of Chemical Engineering, Universiti Teknologi PETRONAS, Seri Iskandar 32610, Malaysia
4 shared publications Y F Yeong
Department of Chemical Engineering, Universiti Teknologi PETRONAS, Bandar Seri Iskandar, 32610, Perak, Malaysia
1 shared publicationY. F. Yeong
Department of Chemical Engineering CO2 Research Center (CO2RES), Universiti Teknologi PETRONAS, Bandar Seri Iskandar 32610, Perak Malaysia
1 shared publicationY.F. Yeong
1 shared publicationYin Fong Yeong
Department of Chemical Engineering, Universiti Teknologi Petronas, Perak, Malaysia
1 shared publication
Latest Publications
- 9 August 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (1)
Enhanced gas separation performance of PSF membrane after modification to PSF/PDMS composite membrane in CO2/CH4 separation
Asymmetric polysulfone (PSF) membrane was developed and modified to PSF/polydimethylsiloxane (PSF/PDMS) composite membrane by dip coating technique. Effect of PDMS coating time on membrane properties was examined by scanning electron microscopy, thermogravimetric analysis, differential scanning calorimetry, attenuated total reflectance‐Fourier transform infrared, and water contact angle. The increase in PDMS coating time resulted in a decrement in the thermal strength of PSF membrane. Surface contact angle values revealed that increase in PDMS coating time had increased the surface hydrophobicity in membranes. CO2/CH4 separation performance of membranes was evaluated, and an increase in CO2/CH4 ideal selectivity was observed with the increase of PDMS coating time. At feed pressure of 10 bar, the selectivity of PSF has increased up to 65% after dip coating with PDMS for 30 min. Modification of polymeric membrane into composite membrane provided a way forward towards the enhancement of gas separation performance in polymeric membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45650.
- 9 August 2017
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 135 (1)
Enhanced gas separation performance of PSF membrane after modification to PSF/PDMS composite membrane in CO2/CH4 separation
Asymmetric polysulfone (PSF) membrane was developed and modified to PSF/polydimethylsiloxane (PSF/PDMS) composite membrane by dip coating technique. Effect of PDMS coating time on membrane properties was examined by scanning electron microscopy, thermogravimetric analysis, differential scanning calorimetry, attenuated total reflectance‐Fourier transform infrared, and water contact angle. The increase in PDMS coating time resulted in a decrement in the thermal strength of PSF membrane. Surface contact angle values revealed that increase in PDMS coating time had increased the surface hydrophobicity in membranes. CO2/CH4 separation performance of membranes was evaluated, and an increase in CO2/CH4 ideal selectivity was observed with the increase of PDMS coating time. At feed pressure of 10 bar, the selectivity of PSF has increased up to 65% after dip coating with PDMS for 30 min. Modification of polymeric membrane into composite membrane provided a way forward towards the enhancement of gas separation performance in polymeric membranes. © 2017 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2018, 135, 45650.
- Open Access
- 23 June 2016
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 36 (1) , 012014
Development and performance evaluation of Polydimethyl siloxane/Polysulfone (PDMS/PSF) composite membrane for CO2/CH4separation
Asymmetric polysulfone (PSF) membrane was developed by phase inversion in this study. Polysulfone (PSF) membrane was modified to develop a composite polymeric membrane. Polydimethyl siloxane (PDMS) was used to modify the PSF membrane. PDMS/PSF composite membrane was developed by dip coating of PDMS over PSF. Developed membranes were characterized in terms of membrane morphology by scanning electron microscope (SEM). Micro structure of polysulfone (PSF) membrane confirmed that developed membrane was asymmetric. Dense PDMS coating in microstructure of composite membrane was observed. Membrane swelling experiments were performed by immersing developed membranes in water for specific time period. PDMS/PSF composite membrane resisted water swelling as compared to PSF membrane. Performance of the membrane was evaluated before and after swelling within the pressure range of 2-10 bar. Reasonable decrement in permeance and selectivity was observed after membrane swelling. Thus, membrane swelling affected the separation performance of both PSF and PDMS/PSF composite membrane by decreasing the permeance and selectivity values.
- 23 June 2016
- Published by IOP Publishing in IOP Conference Series: Earth and Environmental Science
- Vol. 36 (1) , 012014
Open AccessDevelopment and performance evaluation of Polydimethyl siloxane/Polysulfone (PDMS/PSF) composite membrane for CO2/CH4separation
Asymmetric polysulfone (PSF) membrane was developed by phase inversion in this study. Polysulfone (PSF) membrane was modified to develop a composite polymeric membrane. Polydimethyl siloxane (PDMS) was used to modify the PSF membrane. PDMS/PSF composite membrane was developed by dip coating of PDMS over PSF. Developed membranes were characterized in terms of membrane morphology by scanning electron microscope (SEM). Micro structure of polysulfone (PSF) membrane confirmed that developed membrane was asymmetric. Dense PDMS coating in microstructure of composite membrane was observed. Membrane swelling experiments were performed by immersing developed membranes in water for specific time period. PDMS/PSF composite membrane resisted water swelling as compared to PSF membrane. Performance of the membrane was evaluated before and after swelling within the pressure range of 2-10 bar. Reasonable decrement in permeance and selectivity was observed after membrane swelling. Thus, membrane swelling affected the separation performance of both PSF and PDMS/PSF composite membrane by decreasing the permeance and selectivity values.
- 1 April 2016
- Published by Wiley in Chemical Engineering & Technology
- Vol. 39 (9) , 1604-1616
Plasticization and Swelling in Polymeric Membranes in CO2 Removal from Natural Gas
Removal of CO2 from natural gas is necessary to purify the gas and to enhance its calorific value. Membrane technology is an efficient technique for CO2 removal due to its ease of operation and low cost. Polymeric membranes exhibit excellent separation performance which is affected by plasticization and swelling in the membrane. Recent technological advancements and major problems in polymeric membranes are reported in this review. Separation performance of polymeric membranes is highlighted in terms of permeability and selectivity. Moreover, techniques to overcome the major problems in polymeric membranes are reviewed. Commonly, cross‐linking and thermal treatment are used to minimize the effect of plasticization and swelling in the membrane. For future perspectives, there is a need to find more efficient methods to overcome these problems.
- 1 April 2016
- Published by Wiley in Chemical Engineering & Technology
- Vol. 39 (9) , 1604-1616
Plasticization and Swelling in Polymeric Membranes in CO2 Removal from Natural Gas
Removal of CO2 from natural gas is necessary to purify the gas and to enhance its calorific value. Membrane technology is an efficient technique for CO2 removal due to its ease of operation and low cost. Polymeric membranes exhibit excellent separation performance which is affected by plasticization and swelling in the membrane. Recent technological advancements and major problems in polymeric membranes are reported in this review. Separation performance of polymeric membranes is highlighted in terms of permeability and selectivity. Moreover, techniques to overcome the major problems in polymeric membranes are reviewed. Commonly, cross‐linking and thermal treatment are used to minimize the effect of plasticization and swelling in the membrane. For future perspectives, there is a need to find more efficient methods to overcome these problems.
- Open Access
- 1 January 2016
- Published by Elsevier in Procedia Engineering
- Vol. 148, 176-183
Characterization and Performance Evaluation of PDMS/PSF Membrane for CO2/CH4 Separation under the Effect of Swelling
- 1 January 2016
- Published by Elsevier in Procedia Engineering
- Vol. 148, 176-183
Open AccessCharacterization and Performance Evaluation of PDMS/PSF Membrane for CO2/CH4 Separation under the Effect of Swelling