Mykola Anyakin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Mykola Anyakin has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Volodymyr S. Kovalenko
Laser Technology Research Institute of NTUU, “KPI”, Pr. Peremohy 37, Kiev 03056, Ukraine
11 shared publications - Ruslan Zhuk
Laser Technology Research Institute of NTUU, “KPI”, Pr. Peremohy 37, Kiev 03056, Ukraine
6 shared publications J. Meijer
4 shared publications- Oleksandr Stepura
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
4 shared publications - Pavlo Kondrashev
Національний технічний університет України «Київський політехнічний інститут імені Ігоря Сікорського
4 shared publications J. Yao
2 shared publications
Latest Publications
- Open Access
- 19 March 2024
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Mechanics and Advanced Technologies
- Vol. 8 (1(100)) , 30-44
Development of powder delivery nozzles for laser gas-powder cladding
Along with processing parameters, material properties of the workpiece and the powder, the quality of focusing of gas-powder stream is the key parameter that can influence the productivity, quality and costs of laser gas-powder cladding, rapid prototyping by selective laser sintering and surface modifications. Unfortunately, there is almost no information on the methodology for the design of gas-powder streams delivery and simple methods for the control and measurement of gas-powder stream characteristics.Development of the methodology for the design gas-powder streams delivery nozzles that are used in laser gas-powder cladding and simple methods for the control of gas-powder stream characteristics.Numerical methods of vector optics, gas dynamics and image analysis were used.Original systems for the implementation of laser gas-powder cladding with increased productivity and low rate of powder waste were designed, manufactured and verified experimentally.It was established that the use of multi-channel nozzles for the delivery of gas-powder stream into laser beam processing zone increase the productivity of technological processes of laser cladding (especially for the cases when workpiece is not positioned perpendicularly to the laser beam) if compared with traditional coaxial and one-channel nozzle. Another benefit of multi-channel nozzles is that it is possible to introduce simultaneously two or more different powder mixtures into the processing zone.
- 19 March 2024
- Published by Igor Sikorsky Kyiv Polytechnic Institute in Mechanics and Advanced Technologies
- Vol. 8 (1(100)) , 30-44
Open AccessDevelopment of powder delivery nozzles for laser gas-powder cladding
Along with processing parameters, material properties of the workpiece and the powder, the quality of focusing of gas-powder stream is the key parameter that can influence the productivity, quality and costs of laser gas-powder cladding, rapid prototyping by selective laser sintering and surface modifications. Unfortunately, there is almost no information on the methodology for the design of gas-powder streams delivery and simple methods for the control and measurement of gas-powder stream characteristics.Development of the methodology for the design gas-powder streams delivery nozzles that are used in laser gas-powder cladding and simple methods for the control of gas-powder stream characteristics.Numerical methods of vector optics, gas dynamics and image analysis were used.Original systems for the implementation of laser gas-powder cladding with increased productivity and low rate of powder waste were designed, manufactured and verified experimentally.It was established that the use of multi-channel nozzles for the delivery of gas-powder stream into laser beam processing zone increase the productivity of technological processes of laser cladding (especially for the cases when workpiece is not positioned perpendicularly to the laser beam) if compared with traditional coaxial and one-channel nozzle. Another benefit of multi-channel nozzles is that it is possible to introduce simultaneously two or more different powder mixtures into the processing zone.
- Open Access
- 1 January 2013
- Published by Elsevier in Procedia CIRP
- Vol. 6, 504-509
Laser Milling of the Intractable Materials
- 1 January 2013
- Published by Elsevier in Procedia CIRP
- Vol. 6, 504-509
Open AccessLaser Milling of the Intractable Materials
- Open Access
- 1 January 2013
- Published by Elsevier in Procedia CIRP
- Vol. 6, 498-503
Influence of the Interaction of Focused Laser Beam and Gas-Powder Stream on the Quality of Laser Processing
- 1 January 2013
- Published by Elsevier in Procedia CIRP
- Vol. 6, 498-503
Open AccessInfluence of the Interaction of Focused Laser Beam and Gas-Powder Stream on the Quality of Laser Processing
- 1 March 2010
- Published by Laser Institute of America
- Vol. 2010 (1) , 1204
Study of laser cladding with diode laser robotized system
The choice of proper working conditions is a problem for any processing. But for laser processing this procedure is much more serious. The final results of the processing are usually influenced by more than 100 factors. So the best way to choose the working conditions more cheaply and fast is to use the processing simulation. Different tactics of this procedure is discussed and the statistical modelling is accepted. The actual model for laser cladding is developed based on the experimental results of 2Cr13 stainless steel cladding with diode laser robotized system. This model is optimized and verified by experimental results, and then is used to find the optimal processing parameters for laser remanufacturing on 2Cr13 turbine blade. In the light of the lost sizes and required property, this statistical model contributes to repair the failed turbine blade by diode laser robotized system with high efficiency.
- 1 March 2010
- Published by Laser Institute of America
- Vol. 2010 (1) , 1204
Study of laser cladding with diode laser robotized system
The choice of proper working conditions is a problem for any processing. But for laser processing this procedure is much more serious. The final results of the processing are usually influenced by more than 100 factors. So the best way to choose the working conditions more cheaply and fast is to use the processing simulation. Different tactics of this procedure is discussed and the statistical modelling is accepted. The actual model for laser cladding is developed based on the experimental results of 2Cr13 stainless steel cladding with diode laser robotized system. This model is optimized and verified by experimental results, and then is used to find the optimal processing parameters for laser remanufacturing on 2Cr13 turbine blade. In the light of the lost sizes and required property, this statistical model contributes to repair the failed turbine blade by diode laser robotized system with high efficiency.
- 1 January 2010
- Published by Inderscience Publishers in International Journal of Nanomanufacturing
- Vol. 6 (1/2/3/4) , 253
Some results of studying laser micromachining at medical stents manufacturing
Cardio-vascular diseases are the number one killer in the world. As an alternative to common treatment methods the installation of specific-purpose stents into the damaged blood vessel could be used in order to minimise fatal outcomes. Existing technologies of stent manufacturing provide quite good results but are very expensive at the moment. The given paper deals with the design of stents for cardio-vascular surgery and their manufacturing with help of Q-switched Nd-YAG laser which is considered to be much cheaper and more efficient. The methods of nonlinear programming together with methods of experiments planning were used to find the optimal processing conditions and create adequate numerical models of the process. Several processing schemes based on direct laser cutting and step-by-step laser milling had been considered in the research. Some processing dependencies had been established as well as the possibility to create the special micro-relief on the machined surface with help of laser milling. It was demonstrated that due to the assist gas stream action the micro deformation of the stent's workpiece occurs thus influencing the final machining quality.
- 1 January 2010
- Published by Inderscience Publishers in International Journal of Nanomanufacturing
- Vol. 6 (1/2/3/4) , 253
Some results of studying laser micromachining at medical stents manufacturing
Cardio-vascular diseases are the number one killer in the world. As an alternative to common treatment methods the installation of specific-purpose stents into the damaged blood vessel could be used in order to minimise fatal outcomes. Existing technologies of stent manufacturing provide quite good results but are very expensive at the moment. The given paper deals with the design of stents for cardio-vascular surgery and their manufacturing with help of Q-switched Nd-YAG laser which is considered to be much cheaper and more efficient. The methods of nonlinear programming together with methods of experiments planning were used to find the optimal processing conditions and create adequate numerical models of the process. Several processing schemes based on direct laser cutting and step-by-step laser milling had been considered in the research. Some processing dependencies had been established as well as the possibility to create the special micro-relief on the machined surface with help of laser milling. It was demonstrated that due to the assist gas stream action the micro deformation of the stent's workpiece occurs thus influencing the final machining quality.
- 1 January 2007
- Published by Elsevier in CIRP Annals
- Vol. 56 (1) , 189-192
New Developments in Laser Sintering of Diamond Cutting Disks
- 1 January 2007
- Published by Elsevier in CIRP Annals
- Vol. 56 (1) , 189-192
New Developments in Laser Sintering of Diamond Cutting Disks
- 1 January 2007
- Published by Laser Institute of America
Study of the work gas flow on the laser cut parameters in tube workpiece
- 1 January 2007
- Published by Laser Institute of America
Study of the work gas flow on the laser cut parameters in tube workpiece
- 1 January 2006
- Published by Laser Institute of America
- Vol. 2006 (1) , 1802
Study of the process of rapid prototyping with laser beam
Some research results of the developed technology of rapid prototyping are presented. Two schemes of process realization are discussed. First scheme lies in laser sintering of the powder material layer after its compressing with rollers, second – in material sintering at powder injection into the zone of laser irradiation. As a basic material for products’ manufacturing, different powders based on Ni, Co, Ti and others were studied. Numerical experiments and their planning were used to find the optimal working conditions. It was found that to increase the productivity and processing quality, without introduction of additional energy sources, the most efficient way was to apply the additional scanning of the focused laser radiation within the limits of the focused spot.
- 1 January 2006
- Published by Laser Institute of America
- Vol. 2006 (1) , 1802
Study of the process of rapid prototyping with laser beam
Some research results of the developed technology of rapid prototyping are presented. Two schemes of process realization are discussed. First scheme lies in laser sintering of the powder material layer after its compressing with rollers, second – in material sintering at powder injection into the zone of laser irradiation. As a basic material for products’ manufacturing, different powders based on Ni, Co, Ti and others were studied. Numerical experiments and their planning were used to find the optimal working conditions. It was found that to increase the productivity and processing quality, without introduction of additional energy sources, the most efficient way was to apply the additional scanning of the focused laser radiation within the limits of the focused spot.
- 1 January 2003
- Published by Laser Institute of America
- Vol. 2003 (1) , 901
Laser 3D prototypes forming from metal and ceramic materials
The possibility to manufacture the experimental models and ready articles from metal and composites, is a result of laser technolo gy (sintering or cladding) and information technology mutual integration [1]. Naturally, at laser Rapid Prototyping* technique development the different schemes of processing (like in a basic technology) may be utilized: melting (sintering) of a preformed layer of a powdered material [2] or its immediate feeding into a zone of laser interaction with material [3]. Each of the schemes has the advantages and lacks. So the advantage of the first method is the possibility of sintering of the ultra disperse powdered material in a solid phase, and the lack appears at forming the “hollow” details, as the powder fills the whole volume and it is necessary to provide the technological windows for its removal. This disadvantage is absent at the second method of processing – the amount of the powdered material which occurred inside the hollow details is minimal. Common for all systems of Rapid Prototyping is: • High level of mutual integration;• Preparation of a drawings of the designed article with the help of CAD system;• Manufacture of an article via “layer by layer” technique;• Dependence of outcome of processing on conditions of irradiation, properties of a powdered material etc. High level of mutual integration; Preparation of a drawings of the designed article with the help of CAD system; Manufacture of an article via “layer by layer” technique; Dependence of outcome of processing on conditions of irradiation, properties of a powdered material etc. This paper is devoted to a problem of technology and equipment for Rapid Prototyping development.
- 1 January 2003
- Published by Laser Institute of America
- Vol. 2003 (1) , 901
Laser 3D prototypes forming from metal and ceramic materials
The possibility to manufacture the experimental models and ready articles from metal and composites, is a result of laser technolo gy (sintering or cladding) and information technology mutual integration [1]. Naturally, at laser Rapid Prototyping* technique development the different schemes of processing (like in a basic technology) may be utilized: melting (sintering) of a preformed layer of a powdered material [2] or its immediate feeding into a zone of laser interaction with material [3]. Each of the schemes has the advantages and lacks. So the advantage of the first method is the possibility of sintering of the ultra disperse powdered material in a solid phase, and the lack appears at forming the “hollow” details, as the powder fills the whole volume and it is necessary to provide the technological windows for its removal. This disadvantage is absent at the second method of processing – the amount of the powdered material which occurred inside the hollow details is minimal. Common for all systems of Rapid Prototyping is: • High level of mutual integration;• Preparation of a drawings of the designed article with the help of CAD system;• Manufacture of an article via “layer by layer” technique;• Dependence of outcome of processing on conditions of irradiation, properties of a powdered material etc. High level of mutual integration; Preparation of a drawings of the designed article with the help of CAD system; Manufacture of an article via “layer by layer” technique; Dependence of outcome of processing on conditions of irradiation, properties of a powdered material etc. This paper is devoted to a problem of technology and equipment for Rapid Prototyping development.
- 1 January 2002
- Published by Laser Institute of America
- Vol. 2002 (1) , 726315
Studying of laser processed material optical parameter dependencies from temperature
The knowledge of optical behavior of materials at laser beam interaction with material surface i of crucial importance for development of different processes of laser material processing the rapi prototyping gaining recently the top priority. Such data may help in determining the optima working conditions, may predict the behavior of the material at laser irradiation. Few works are known devoted to the consideration of this problem [1,2]. Their authors wer using different techniques to find the proper value of optical parameters of some monolithi materials. In some works there had been given data on such characteristics for powder material [3] as well. Those researches were based on evaluation of reflected and diffused beams from irradiated surface, on analysis of acoustics emission of irradiated surface, on monitoring plasm plume generated at interaction of laser beam with surface. The main drawback of all thos techniques was quite high complexity of the monitoring device and procedures. Another negativ factor was the ability to get the result only before or after laser processing itself but not durin processing when surface temperature is influencing surface optical characteristics to great extend. For everyday use at laboratory or at shop floor level the simpler device and technique are neede to get quick results. To perform more efficiently the laser rapid prototyping processing from powder materials we need to know the optical characteristics of different powder material compressed to layers of varied density in their connection with irradiated surface temperature. This paper just demonstrates such simple approach that permits to evaluate the optical parameter depending on surface temperature not only for monolithic materials but for their powde analogues as well.
- 1 January 2002
- Published by Laser Institute of America
- Vol. 2002 (1) , 726315
Studying of laser processed material optical parameter dependencies from temperature
The knowledge of optical behavior of materials at laser beam interaction with material surface i of crucial importance for development of different processes of laser material processing the rapi prototyping gaining recently the top priority. Such data may help in determining the optima working conditions, may predict the behavior of the material at laser irradiation. Few works are known devoted to the consideration of this problem [1,2]. Their authors wer using different techniques to find the proper value of optical parameters of some monolithi materials. In some works there had been given data on such characteristics for powder material [3] as well. Those researches were based on evaluation of reflected and diffused beams from irradiated surface, on analysis of acoustics emission of irradiated surface, on monitoring plasm plume generated at interaction of laser beam with surface. The main drawback of all thos techniques was quite high complexity of the monitoring device and procedures. Another negativ factor was the ability to get the result only before or after laser processing itself but not durin processing when surface temperature is influencing surface optical characteristics to great extend. For everyday use at laboratory or at shop floor level the simpler device and technique are neede to get quick results. To perform more efficiently the laser rapid prototyping processing from powder materials we need to know the optical characteristics of different powder material compressed to layers of varied density in their connection with irradiated surface temperature. This paper just demonstrates such simple approach that permits to evaluate the optical parameter depending on surface temperature not only for monolithic materials but for their powde analogues as well.