Qammer Zaib
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Qammer Zaib has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Farrukh Ahmad
BioEnergy and Environmental Laboratory (BEEL), Institute Center for Water and Environment (iWATER), Masdar Institute of Science and Technology, P.O. Box 54224, Abu Dhabi, UAE
5 shared publications Daeseung Kyung
4 shared publications- Iftheker Ahmed Khan
Department of Civil and Environmental Engineering, University of South Carolina, Columbia, SC 29208, USA
3 shared publications Navid B. Saleh
University of South Carolina
3 shared publicationsYong-Gyun Park
GS E&C Research Institute
3 shared publicationsJoseph R. V. Flora
2 shared publications
Latest Publications
- 8 November 2023
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 11 (46) , 16567-16574
Deep Eutectic Solvents Reduce the Life Cycle Environmental Impacts and Energy Demands of Carbon Dioxide Capture
- 8 November 2023
- Published by American Chemical Society (ACS) in ACS Sustainable Chemistry & Engineering
- Vol. 11 (46) , 16567-16574
Deep Eutectic Solvents Reduce the Life Cycle Environmental Impacts and Energy Demands of Carbon Dioxide Capture
- Open Access
- 31 May 2023
- Published by Springer Nature in Research Square
Optimization of Low-Grade Coal and Refuse-Derived Fuel Blends for Improved Co-Combustion Behavior in Coal-Fired Power Plants
This study aims at utilizing three waste materials, i.e., Biomass-Solid Refuse Fuel (SRF), Tire Derived Fuel (TDF), and Sludge Derived Fuel (SDF), as ecofriendly alternatives to coal-only combustion in co-firing power plants. The contribution of waste materials is limited to ≤ 5% in the composition of the mixed fuel (coal + waste materials). Statistical experimental design and response surface methodology is employed to investigate the effect of mixed fuel composition (SRF, TDF, and SDF) on gross calorific value (GCV) and ash fusion temperature (AFT). A quadratic model is developed and statistically verified to apprehend mixed fuel constituents' individual and combined effects on GCV and AFT. Constrained optimization of fuel blend, i.e., GCV > 1250 kcal/kg and AFT > 1200°C, using the polynomial models projected the fuel-blend containing 95% coal with 3.84% SRF, 0.35% TDF, and 0.81% SDF. The observed GCV of 5307 kcal/kg and AFT of 1225°C for the optimized blend were within 1% of the model predicted values, thereby establishing the robustness of the models. Our findings can foster sustainable economic development and zero CO2 emission objectives by optimizing the utilization of waste materials without compromising on the GCV and AFT of mixed fuels in coal-fired power plants.
- 31 May 2023
- Published by Springer Nature in Research Square
Open AccessOptimization of Low-Grade Coal and Refuse-Derived Fuel Blends for Improved Co-Combustion Behavior in Coal-Fired Power Plants
This study aims at utilizing three waste materials, i.e., Biomass-Solid Refuse Fuel (SRF), Tire Derived Fuel (TDF), and Sludge Derived Fuel (SDF), as ecofriendly alternatives to coal-only combustion in co-firing power plants. The contribution of waste materials is limited to ≤ 5% in the composition of the mixed fuel (coal + waste materials). Statistical experimental design and response surface methodology is employed to investigate the effect of mixed fuel composition (SRF, TDF, and SDF) on gross calorific value (GCV) and ash fusion temperature (AFT). A quadratic model is developed and statistically verified to apprehend mixed fuel constituents' individual and combined effects on GCV and AFT. Constrained optimization of fuel blend, i.e., GCV > 1250 kcal/kg and AFT > 1200°C, using the polynomial models projected the fuel-blend containing 95% coal with 3.84% SRF, 0.35% TDF, and 0.81% SDF. The observed GCV of 5307 kcal/kg and AFT of 1225°C for the optimized blend were within 1% of the model predicted values, thereby establishing the robustness of the models. Our findings can foster sustainable economic development and zero CO2 emission objectives by optimizing the utilization of waste materials without compromising on the GCV and AFT of mixed fuels in coal-fired power plants.
- 29 May 2023
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 11 (3)
Review of the synthesis and applications of deep eutectic solvent-functionalized adsorbents for water treatment
- 29 May 2023
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 11 (3)
Review of the synthesis and applications of deep eutectic solvent-functionalized adsorbents for water treatment
- Top Cited Papers
- 28 July 2022
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 24 (20) , 7924-7930
Are deep eutectic solvents really green?: A life-cycle perspective
Life-cycle assessment of choline chloride/urea (reline) deep eutectic solvent compared with conventional organic solvents.
- 28 July 2022
- Published by Royal Society of Chemistry (RSC) in Green Chemistry
- Vol. 24 (20) , 7924-7930
Top Cited PapersAre deep eutectic solvents really green?: A life-cycle perspective
Life-cycle assessment of choline chloride/urea (reline) deep eutectic solvent compared with conventional organic solvents.
- 1 September 2019
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 148, 114-123
Optimum utilization of waste foundry sand and fly ash for geopolymer concrete synthesis using D-optimal mixture design of experiments
- 1 September 2019
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 148, 114-123
Optimum utilization of waste foundry sand and fly ash for geopolymer concrete synthesis using D-optimal mixture design of experiments
- Open Access
- 10 January 2019
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 4 (1) , 849-859
Optimization of Carbon Nanotube Dispersions in Water Using Response Surface Methodology
The aim of this work was to demonstrate an optimization methodology to reliably obtain stable macrodispersions (i.e., for ≥24 h) of carbon nanotubes in water using sonication. Response surface methodology (RSM) was utilized to assess and optimize the sonication parameters for the process. The studied input parameters were (i) sonication time (duration), (ii) amplitude (of vibration), and (iii) pulse-on/off (duration) of the sonicator. The analyzed responses were mean diameter and size distribution of multiwalled carbon nanotube (MWNT) aggregates in water, which were measured by the dynamic light scattering technique. A semiempirical model was developed and statistically tested to estimate the magnitude of sonicator parameters required to obtain specified MWNT macrodispersions (i.e., aggregates’ mean diameter and distribution) in water. The results showed that MWNT aggregates of 2 ± 0.5 μm can be obtained by optimizing sonicator parameters to a sonication time of 89 s, amplitude of 144 μm, and pulse-on/off cycle of 44/30 s. These process settings for 100 mg/L MWNTs in a 30 mL aliquot of deionized water would consume 863 J/mL of sonication energy. Contrary to the popular belief, “sonication time” and/or “sonication energy input” were not found to be proportional to the degree of dispersion of MWNTs in water. This might be the reason for the frequent disparity and nonreproducibility of sonication results reported in scientific literature, especially for dispersing nanomaterials in a number of different systems. The amplitude of vibration was noted to be the most sensitive parameter affecting MWNT aggregates’ diameter and distribution in water. The characterization of MWNTs was performed using electron microscopy, surface area analyzer, thermogravimetric analyzer, and zeta potential analyzer. This study can be helpful in evaluating sonication dispersion of particulate matter in other incompressible fluids such as graphene dispersion in organic solvents.
- 10 January 2019
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 4 (1) , 849-859
Open AccessOptimization of Carbon Nanotube Dispersions in Water Using Response Surface Methodology
The aim of this work was to demonstrate an optimization methodology to reliably obtain stable macrodispersions (i.e., for ≥24 h) of carbon nanotubes in water using sonication. Response surface methodology (RSM) was utilized to assess and optimize the sonication parameters for the process. The studied input parameters were (i) sonication time (duration), (ii) amplitude (of vibration), and (iii) pulse-on/off (duration) of the sonicator. The analyzed responses were mean diameter and size distribution of multiwalled carbon nanotube (MWNT) aggregates in water, which were measured by the dynamic light scattering technique. A semiempirical model was developed and statistically tested to estimate the magnitude of sonicator parameters required to obtain specified MWNT macrodispersions (i.e., aggregates’ mean diameter and distribution) in water. The results showed that MWNT aggregates of 2 ± 0.5 μm can be obtained by optimizing sonicator parameters to a sonication time of 89 s, amplitude of 144 μm, and pulse-on/off cycle of 44/30 s. These process settings for 100 mg/L MWNTs in a 30 mL aliquot of deionized water would consume 863 J/mL of sonication energy. Contrary to the popular belief, “sonication time” and/or “sonication energy input” were not found to be proportional to the degree of dispersion of MWNTs in water. This might be the reason for the frequent disparity and nonreproducibility of sonication results reported in scientific literature, especially for dispersing nanomaterials in a number of different systems. The amplitude of vibration was noted to be the most sensitive parameter affecting MWNT aggregates’ diameter and distribution in water. The characterization of MWNTs was performed using electron microscopy, surface area analyzer, thermogravimetric analyzer, and zeta potential analyzer. This study can be helpful in evaluating sonication dispersion of particulate matter in other incompressible fluids such as graphene dispersion in organic solvents.
- Open Access
- 8 January 2019
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 4 (1) , 535-545
Ultrasonic Synthesis of Carbon Nanotube-Titanium Dioxide Composites: Process Optimization via Response Surface Methodology
In this study, the central composite design of response surface methodology was applied to optimize the ultrasonic synthesis of multiwalled carbon nanotube-titanium dioxide (MWNT-TiO2) composites. Twenty composites were prepared by adjusting three parameters (MWNT concentration in water, sonication to disperse/exfoliate MWNTs in water, and sonication to attach TiO2 onto MWNTs) at five levels. On the basis of the experimental design, semiempirical expressions were developed, analyzed, statistically assessed, and subsequently applied to predict the impact of the studied parameters on composite synthesis. The composite synthesis process was optimized to capture the experimental conditions favoring the highest productivity (i.e., MWNT-TiO2 formation or percent TiO2 attachment) utilizing minimal resources. The synthesis process optimization results showed that, to make a MWNT-TiO2 composite in 10 mL of water, 23.2 mg (∼99% of 23.4 mg) of TiO2 can be attached to 2.6 mg of MWNTs. This process requires only 727 J sonication energy, of which 592 J is invested to exfoliate MWNTs (Sonication 1) and 135 J to attach TiO2 (Sonication 2) to MWNTs. Finally, the optimally synthesized composite was extensively characterized using SEM, surface area and porosity analysis, TGA, and ζ-potential analysis/DLS. Also, this composite was tested for stability under variable pH and solvent polarity. The approach developed in this study could be used to optimize the synthesis process of other similar composites.
- 8 January 2019
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 4 (1) , 535-545
Open AccessUltrasonic Synthesis of Carbon Nanotube-Titanium Dioxide Composites: Process Optimization via Response Surface Methodology
In this study, the central composite design of response surface methodology was applied to optimize the ultrasonic synthesis of multiwalled carbon nanotube-titanium dioxide (MWNT-TiO2) composites. Twenty composites were prepared by adjusting three parameters (MWNT concentration in water, sonication to disperse/exfoliate MWNTs in water, and sonication to attach TiO2 onto MWNTs) at five levels. On the basis of the experimental design, semiempirical expressions were developed, analyzed, statistically assessed, and subsequently applied to predict the impact of the studied parameters on composite synthesis. The composite synthesis process was optimized to capture the experimental conditions favoring the highest productivity (i.e., MWNT-TiO2 formation or percent TiO2 attachment) utilizing minimal resources. The synthesis process optimization results showed that, to make a MWNT-TiO2 composite in 10 mL of water, 23.2 mg (∼99% of 23.4 mg) of TiO2 can be attached to 2.6 mg of MWNTs. This process requires only 727 J sonication energy, of which 592 J is invested to exfoliate MWNTs (Sonication 1) and 135 J to attach TiO2 (Sonication 2) to MWNTs. Finally, the optimally synthesized composite was extensively characterized using SEM, surface area and porosity analysis, TGA, and ζ-potential analysis/DLS. Also, this composite was tested for stability under variable pH and solvent polarity. The approach developed in this study could be used to optimize the synthesis process of other similar composites.
- 1 October 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (5) , 6733-6740
CNT/PVP blend PVDF membranes for the removal of organic pollutants from simulated treated wastewater effluent
- 1 October 2018
- Published by Elsevier in Journal of Environmental Chemical Engineering
- Vol. 6 (5) , 6733-6740
CNT/PVP blend PVDF membranes for the removal of organic pollutants from simulated treated wastewater effluent