Alberto Soto Lock
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alberto Soto Lock has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Darlan Alexandria Fernandes
Federal University of Paraíba image/svg+xml
9 shared publications - Andrés Ortiz Salazar
Department of Computer Engineering and Automation, Federal University of Rio Grande do Norte (DCA-UFRN), Natal 59072-970, Brazil
8 shared publications Edison R. C. da Silva
Department of Electrical Engineering, Federal University of Paraíba, João Pessoa, Brazil
6 shared publicationsMalik E. Elbuluk
University of Akron, Ohio, USA
5 shared publications- Joao Teixeira de Carvalho Neto
Department of Computing Engineering and Automation, Federal University of Rio Grande do Norte, Natal/ Rio Grande do Norte, Brazil
4 shared publications - Fabiano Fragoso Costa
Federal University of Bahia
3 shared publications
Latest Publications
- Open Access
One Cycle Control of a PWM Rectifier a New Approach
This paper analyzes a Digital Signal Processor (DSP) based One Cycle Control (OCC) strategy for a Power Factor Corrector (PFC) rectifier with Common-mode Voltage (CMV) immunity. It is proposed a strategy that utilizes an emulated-resistance-controller in closed-loop configuration to set the dc-link voltage to achieve unity power factor (UPF). It is shown that if the PFC can achieve UPF condition and if the phase voltage is only affected by CMV, then phase current is free from CMV, as well as a lead-lag compensator (LLC) to average phase current.
Open AccessOne Cycle Control of a PWM Rectifier a New Approach
This paper analyzes a Digital Signal Processor (DSP) based One Cycle Control (OCC) strategy for a Power Factor Corrector (PFC) rectifier with Common-mode Voltage (CMV) immunity. It is proposed a strategy that utilizes an emulated-resistance-controller in closed-loop configuration to set the dc-link voltage to achieve unity power factor (UPF). It is shown that if the PFC can achieve UPF condition and if the phase voltage is only affected by CMV, then phase current is free from CMV, as well as a lead-lag compensator (LLC) to average phase current.
- 1 August 2019
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 110, 236-246
An analog based control scheme applied in stand-alone photovoltaic systems for DC power distribution
- 1 August 2019
- Published by Elsevier in Renewable and Sustainable Energy Reviews
- Vol. 110, 236-246
An analog based control scheme applied in stand-alone photovoltaic systems for DC power distribution
- Open Access
- 1 July 2019
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 13 (12) , 2123-2136
Design and operation of an OCC‐based scheme for a stand‐alone PV system powering DC loads
Distributed energy resources such as stand‐alone photovoltaic (PV) systems have been widely used in electric systems in the last decades due to the increase in global energy demand, and the concern about the environmental problems caused by fossil fuels power generation. Owing to the fast growing of direct current (DC) microgrids and electronic devices, such as their current compatibility nature in relation to primary sources, a small‐scale stand‐alone PV system with battery storage for DC applications is proposed in this work. The system consists of three DC–DC converters which operate according to the PV panel power and the main bus load demand. The control of these converters considers the quality in power supply ensuring safety to the loads and batteries of the system. Thus, this study proposes the implementation of the control units through the use of one‐cycle control (OCC) which allows fast response to transient conditions, great accuracy of convergence and has low‐cost analogue implementation. In this study, one‐cycle controllers’ waveforms are analysed in steady‐state conditions and its duty cycles are compared with the expected in relation to the system operation. Simulations of transition conditions were performed through real situations such as cloud‐edge effects, slow passing clouds and absence of sunlight.
- 1 July 2019
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 13 (12) , 2123-2136
Open AccessDesign and operation of an OCC‐based scheme for a stand‐alone PV system powering DC loads
Distributed energy resources such as stand‐alone photovoltaic (PV) systems have been widely used in electric systems in the last decades due to the increase in global energy demand, and the concern about the environmental problems caused by fossil fuels power generation. Owing to the fast growing of direct current (DC) microgrids and electronic devices, such as their current compatibility nature in relation to primary sources, a small‐scale stand‐alone PV system with battery storage for DC applications is proposed in this work. The system consists of three DC–DC converters which operate according to the PV panel power and the main bus load demand. The control of these converters considers the quality in power supply ensuring safety to the loads and batteries of the system. Thus, this study proposes the implementation of the control units through the use of one‐cycle control (OCC) which allows fast response to transient conditions, great accuracy of convergence and has low‐cost analogue implementation. In this study, one‐cycle controllers’ waveforms are analysed in steady‐state conditions and its duty cycles are compared with the expected in relation to the system operation. Simulations of transition conditions were performed through real situations such as cloud‐edge effects, slow passing clouds and absence of sunlight.
- Open Access
- 19 December 2018
- Published by Brazilian Society for Computational and Applied Mathematics (SBMAC) in Proceeding Series of the Brazilian Society of Computational and Applied Mathematics
- Vol. 6 (2)
Controle MPC com Atrasos e Perdas de Pacotes
Controle MPC com Atrasos e Perdas de Pacotes
- 19 December 2018
- Published by Brazilian Society for Computational and Applied Mathematics (SBMAC) in Proceeding Series of the Brazilian Society of Computational and Applied Mathematics
- Vol. 6 (2)
Open AccessControle MPC com Atrasos e Perdas de Pacotes
Controle MPC com Atrasos e Perdas de Pacotes
- Open Access
- 1 March 2018
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 11 (3) , 484-490
Hybrid one‐cycle control technique for three‐phase power factor control
One‐cycle control technique has been a prominent and suitable solution for improving power quality with the help of three‐phase rectifiers. This study proposes a generalised control strategy for the three‐phase power factor rectifier based on both the one‐cycle control technique and the hybrid pulse‐width modulation (PWM) strategy. Improvement of the performance while providing very low‐current total harmonic distortion (THD) is achieved with the proposed scheme. Discontinuous and/or continuous PWM operation is possible with advantages of simplicity, robustness, and low cost. Simulation and experimental results confirm the feasibility of the proposed controller.
- 1 March 2018
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 11 (3) , 484-490
Open AccessHybrid one‐cycle control technique for three‐phase power factor control
One‐cycle control technique has been a prominent and suitable solution for improving power quality with the help of three‐phase rectifiers. This study proposes a generalised control strategy for the three‐phase power factor rectifier based on both the one‐cycle control technique and the hybrid pulse‐width modulation (PWM) strategy. Improvement of the performance while providing very low‐current total harmonic distortion (THD) is achieved with the proposed scheme. Discontinuous and/or continuous PWM operation is possible with advantages of simplicity, robustness, and low cost. Simulation and experimental results confirm the feasibility of the proposed controller.
- 14 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 53 (5) , 4877-4885
Sensitive Load Voltage Compensation Performed by a Suitable Control Method
This paper proposes the usage of a repetitive-based control to dynamically restore the voltage applied to sensitive and critical loads of power system. The control intrinsically is able to wipe off harmonic distortion and relies on simple transfer function. As a consequence, there is no need to apply harmonic selective filters. Furthermore, the control system is able to work out on sinusoid references and, thus, avoids the need of employing the dq transform. A recursive least-squares is also included to the control system in order to assure the synchronization of the voltages to be restored. The design of the control parameters along with the system stability is discussed. The experimental results are produced with a setup of a three-phase series compensator. The scenarios for emulating faulty voltages are the same for experimental and simulated results. The results corroborates the usage of the proposed method.
- 14 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 53 (5) , 4877-4885
Sensitive Load Voltage Compensation Performed by a Suitable Control Method
This paper proposes the usage of a repetitive-based control to dynamically restore the voltage applied to sensitive and critical loads of power system. The control intrinsically is able to wipe off harmonic distortion and relies on simple transfer function. As a consequence, there is no need to apply harmonic selective filters. Furthermore, the control system is able to work out on sinusoid references and, thus, avoids the need of employing the dq transform. A recursive least-squares is also included to the control system in order to assure the synchronization of the voltages to be restored. The design of the control parameters along with the system stability is discussed. The experimental results are produced with a setup of a three-phase series compensator. The scenarios for emulating faulty voltages are the same for experimental and simulated results. The results corroborates the usage of the proposed method.
- 16 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Voltage quality enhancement with minimum power injection
This work proposes the usage of a repetitive-based control to dynamically restore the voltage applied to sensitive and critical loads of power systems. Besides, sag and voltage swells, the proposed control can intrinsically mitigate harmonic distortions. Furthermore, the filter is able to work out on sinusoid references and, thus, avoids the need of employing the dq transform. A recursive least-squares is also included to the control system in order to assure the synchronization of the injected voltages to be restored. The design of the control parameters along with the system stability are discussed throughout the paper. Also, this work aims to analyze two different types of voltage insertion into the grid through the series compensator. In the first one, the voltage injection is in synchronization with the pre-faulted grid voltage, while the second injects the voltage in a manner that the compensator spends a minimum of active power. Both types produce reference voltages that are used by the repetitive control. Additionally, simulated and experimental results are presented and corroborate the method efficacy.
- 16 February 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Voltage quality enhancement with minimum power injection
This work proposes the usage of a repetitive-based control to dynamically restore the voltage applied to sensitive and critical loads of power systems. Besides, sag and voltage swells, the proposed control can intrinsically mitigate harmonic distortions. Furthermore, the filter is able to work out on sinusoid references and, thus, avoids the need of employing the dq transform. A recursive least-squares is also included to the control system in order to assure the synchronization of the injected voltages to be restored. The design of the control parameters along with the system stability are discussed throughout the paper. Also, this work aims to analyze two different types of voltage insertion into the grid through the series compensator. In the first one, the voltage injection is in synchronization with the pre-faulted grid voltage, while the second injects the voltage in a manner that the compensator spends a minimum of active power. Both types produce reference voltages that are used by the repetitive control. Additionally, simulated and experimental results are presented and corroborate the method efficacy.
- 10 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 52 (6) , 4935-4945
An APF-OCC Strategy for Common-Mode Current Rejection
This paper proposes a DSP-based one-cycle control (OCC) strategy for a shunt active power filter (APF), which is able to reject common-mode currents caused by common-mode voltages. The proposed strategy is based on an OCC rectifier control, which utilizes an input resistance control to set up dc-link voltage and achieve a unity power factor as well as a lead-lag compensator to average phase current. In this sense, the proposed APF strategy employs input resistance to control the power factor, while a lead-lag compensator is used to filter harmonics in phase current. Simulation and experimental results confirm the presented proposal.
- 10 August 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 52 (6) , 4935-4945
An APF-OCC Strategy for Common-Mode Current Rejection
This paper proposes a DSP-based one-cycle control (OCC) strategy for a shunt active power filter (APF), which is able to reject common-mode currents caused by common-mode voltages. The proposed strategy is based on an OCC rectifier control, which utilizes an input resistance control to set up dc-link voltage and achieve a unity power factor as well as a lead-lag compensator to average phase current. In this sense, the proposed APF strategy employs input resistance to control the power factor, while a lead-lag compensator is used to filter harmonics in phase current. Simulation and experimental results confirm the presented proposal.
- 21 March 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 14 (2) , 602-609
One Cycle Control Based Maximum Power Point Tracker Applied in Photovoltaic Systems
The utilization of solar energy has grown in the last decades, and due to the scarcity of fossil fuels and the awareness of the increasing greenhouse gases in the atmosphere, this energy tends to become predominant. For generating photovoltaic energy, photovoltaic modules are connected to converters to define the amount of energy provided to a load. A maximum power point tracking method is used to maximize the photovoltaic module output power considering the solar radiation and panel temperature. This work proposes the implementation of one-cycle control (OCC) to track the maximum power point of a photovoltaic module in direct current converters. This paper contains an analysis of response speed, reference tracking and transient, showing the applicability of the OCC technique.
- 21 March 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Latin America Transactions
- Vol. 14 (2) , 602-609
One Cycle Control Based Maximum Power Point Tracker Applied in Photovoltaic Systems
The utilization of solar energy has grown in the last decades, and due to the scarcity of fossil fuels and the awareness of the increasing greenhouse gases in the atmosphere, this energy tends to become predominant. For generating photovoltaic energy, photovoltaic modules are connected to converters to define the amount of energy provided to a load. A maximum power point tracking method is used to maximize the photovoltaic module output power considering the solar radiation and panel temperature. This work proposes the implementation of one-cycle control (OCC) to track the maximum power point of a photovoltaic module in direct current converters. This paper contains an analysis of response speed, reference tracking and transient, showing the applicability of the OCC technique.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 54 (23293721) , 1639-1644
Sensitive load voltage compensation with a suitable control method
This work proposes the usage of a repetitive-based control to dynamically restore the voltage applied to grid sensitive loads. The control is able to wipe off harmonic distortion and relies on simple transfer function. As a consequence, there is no need to apply harmonic selective filters. Moreover, the filter is able to work on sinusoid references and avoids employment of the dq transform. The design of the control parameters along with the system stability are discussed. A Simulink-based simulation has been built to verify the designed control performance. The experimental results are extracted from a setup of three-phase compensator which copes correctly with different scenarios of sagged and harmonic distorted voltages.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- Vol. 54 (23293721) , 1639-1644
Sensitive load voltage compensation with a suitable control method
This work proposes the usage of a repetitive-based control to dynamically restore the voltage applied to grid sensitive loads. The control is able to wipe off harmonic distortion and relies on simple transfer function. As a consequence, there is no need to apply harmonic selective filters. Moreover, the filter is able to work on sinusoid references and avoids employment of the dq transform. The design of the control parameters along with the system stability are discussed. A Simulink-based simulation has been built to verify the designed control performance. The experimental results are extracted from a setup of three-phase compensator which copes correctly with different scenarios of sagged and harmonic distorted voltages.