Guang Hong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Guang Hong has a total of 62 co-authors. Here are the top co-authors by number of shared publications:
- Samuel G. Mallinson
Univ. of Technology/Sydney (Australia)
7 shared publications - Yuhan Huang
Centre for Green Technology, School of Civil and Environmental Engineering, University of Technology Sydney, NSW 2007, Australia
6 shared publications Ronghua Huang
5 shared publicationsG. J. Walker
University of Tasmania, Hobart, Tasmania, Australia
4 shared publicationsJ. P. Gostelow
University of Leicester, Leicester, United Kingdom
4 shared publicationsYuan Zhuang
4 shared publications
Latest Publications
- 1 January 2018
- Published by EJournal Publishing in Journal of Clean Energy Technologies
- Vol. 6 (1) , 41-46
Chemical Heat Storage for Saving the Exhaust Gas Energy in a Spark Ignition Engine
- 1 January 2018
- Published by EJournal Publishing in Journal of Clean Energy Technologies
- Vol. 6 (1) , 41-46
Chemical Heat Storage for Saving the Exhaust Gas Energy in a Spark Ignition Engine
- 1 January 2016
- Published by Elsevier in Energy Conversion and Management
- Vol. 108, 68-77
Spray and evaporation characteristics of ethanol and gasoline direct injection in non-evaporating, transition and flash-boiling conditions
- 1 January 2016
- Published by Elsevier in Energy Conversion and Management
- Vol. 108, 68-77
Spray and evaporation characteristics of ethanol and gasoline direct injection in non-evaporating, transition and flash-boiling conditions
- Open Access
- 1 December 2015
- Published by Elsevier in Applied Energy
- Vol. 160, 244-254
Investigation to charge cooling effect and combustion characteristics of ethanol direct injection in a gasoline port injection engine
- 1 December 2015
- Published by Elsevier in Applied Energy
- Vol. 160, 244-254
Open AccessInvestigation to charge cooling effect and combustion characteristics of ethanol direct injection in a gasoline port injection engine
- 1 March 2015
- Published by Elsevier in Energy Conversion and Management
- Vol. 92, 275-286
Numerical investigation to the dual-fuel spray combustion process in an ethanol direct injection plus gasoline port injection (EDI+GPI) engine
- 1 March 2015
- Published by Elsevier in Energy Conversion and Management
- Vol. 92, 275-286
Numerical investigation to the dual-fuel spray combustion process in an ethanol direct injection plus gasoline port injection (EDI+GPI) engine
- 4 February 2015
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 16 (1) , 1-15
3D EHD lubrication and wear for piston ring-cylinder liner on diesel engines
- 4 February 2015
- Published by Springer Nature in International Journal of Automotive Technology
- Vol. 16 (1) , 1-15
3D EHD lubrication and wear for piston ring-cylinder liner on diesel engines
- 13 October 2014
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Numerical Investigation to the Effect of Ethanol/Gasoline Ratio on Charge Cooling in an EDI+GPI Engine
The work reported in this paper contributes to understanding the effects of ethanol/gasoline ratio on mixture formation and cooling effect which are crucial in the development of EDI+GPI engine. The spray simulations were carried out using a commercial CFD code. The model was verified by comparing the numerical and experimental results of spray shapes in a constant volume chamber and cylinder pressure in an EDI+GPI research engine. The verified model was used to investigate the fuel vaporization and mixture formation of the EDI+GPI research engine. The effect of the ethanol/gasoline ratio on charge cooling has been studied. Compared with GPI only, EDI+GPI demonstrated stronger effect on charge cooling by decreased in-cylinder temperature. However, the cooling effect was limited by the low evaporation rate of the ethanol fuel due to its lower saturation vapour pressure than gasoline's in low temperature conditions. The cooling effect of EDI increased with the increase of ethanol/gasoline ratio until the ratio reached 58% (by volume). Further increase of ethanol/gasoline ratio did not improve the cooling effect, but left more liquid ethanol droplets in the combustion chamber by the time of spark. This could lead to incomplete combustion and explained the increased CO and HC emissions with the increase of ethanol content as reported in the experiments. The cooling potential and the completeness of ethanol evaporation were two completing factors that determine the final cooling effect of EDI. This implied the existence of ethanol/gasoline ratio 40-50% which can optimize the cooling effect and combustion performance.
- 13 October 2014
- Published by SAE International in SAE International Journal of Advances and Current Practices in Mobility
- Vol. 1
Numerical Investigation to the Effect of Ethanol/Gasoline Ratio on Charge Cooling in an EDI+GPI Engine
The work reported in this paper contributes to understanding the effects of ethanol/gasoline ratio on mixture formation and cooling effect which are crucial in the development of EDI+GPI engine. The spray simulations were carried out using a commercial CFD code. The model was verified by comparing the numerical and experimental results of spray shapes in a constant volume chamber and cylinder pressure in an EDI+GPI research engine. The verified model was used to investigate the fuel vaporization and mixture formation of the EDI+GPI research engine. The effect of the ethanol/gasoline ratio on charge cooling has been studied. Compared with GPI only, EDI+GPI demonstrated stronger effect on charge cooling by decreased in-cylinder temperature. However, the cooling effect was limited by the low evaporation rate of the ethanol fuel due to its lower saturation vapour pressure than gasoline's in low temperature conditions. The cooling effect of EDI increased with the increase of ethanol/gasoline ratio until the ratio reached 58% (by volume). Further increase of ethanol/gasoline ratio did not improve the cooling effect, but left more liquid ethanol droplets in the combustion chamber by the time of spark. This could lead to incomplete combustion and explained the increased CO and HC emissions with the increase of ethanol content as reported in the experiments. The cooling potential and the completeness of ethanol evaporation were two completing factors that determine the final cooling effect of EDI. This implied the existence of ethanol/gasoline ratio 40-50% which can optimize the cooling effect and combustion performance.
- 13 October 2014
- Published by SAE International in SAE International Journal of Fuels and Lubricants
- Vol. 07 (3) , 792-802
The Effect of Fuel Temperature on the Ethanol Direct Injection Spray Characteristics of a Multi-hole Injector
Ethanol direct injection (EDI) is a new technology to use ethanol fuel more efficiently in spark ignition engines. Fuel temperature is one of the key factors which determine the evaporation process of liquid fuel spray, and consequently influence the combustion and emission generation of the engine. To better understand the mixture formation process of the EDI spray and provide experimental data for engine modelling, experiments were conducted in a constant volume chamber in engine-like conditions. The high speed Shadowgraphy imaging technique was used to capture the ethanol spray behaviours. The experiments covered a wide range of fuel temperature, ranged from 275 K (non-evaporating) to 400 K (flash-boiling). Particularly the transition of the ethanol spray from normal-evaporating to flash-boiling was investigated. The temporal Shadowgraphy spray images, spray tip penetration, angle and projected area were applied to evaluate the evaporation of EDI spray under different fuel temperature conditions. The results showed that the non-evaporating spray's characteristics were similar to the normal-evaporating sprays' in terms of spray tip penetration, angle and projected area. When the fuel temperature increased from 350 K to flash-boiling spray, the spray angle and projected area reduced significantly, but the spray tip penetration increased. Increasing the fuel temperature from 275 K to 325 K did not cause significant increase of the evaporating rate, but with further increase of the fuel temperature, the ethanol spray's evaporation became faster. The transition temperature at which the ethanol spray collapsed at atmospheric pressure was between 355 K and 360 K.
- 13 October 2014
- Published by SAE International in SAE International Journal of Fuels and Lubricants
- Vol. 07 (3) , 792-802
The Effect of Fuel Temperature on the Ethanol Direct Injection Spray Characteristics of a Multi-hole Injector
Ethanol direct injection (EDI) is a new technology to use ethanol fuel more efficiently in spark ignition engines. Fuel temperature is one of the key factors which determine the evaporation process of liquid fuel spray, and consequently influence the combustion and emission generation of the engine. To better understand the mixture formation process of the EDI spray and provide experimental data for engine modelling, experiments were conducted in a constant volume chamber in engine-like conditions. The high speed Shadowgraphy imaging technique was used to capture the ethanol spray behaviours. The experiments covered a wide range of fuel temperature, ranged from 275 K (non-evaporating) to 400 K (flash-boiling). Particularly the transition of the ethanol spray from normal-evaporating to flash-boiling was investigated. The temporal Shadowgraphy spray images, spray tip penetration, angle and projected area were applied to evaluate the evaporation of EDI spray under different fuel temperature conditions. The results showed that the non-evaporating spray's characteristics were similar to the normal-evaporating sprays' in terms of spray tip penetration, angle and projected area. When the fuel temperature increased from 350 K to flash-boiling spray, the spray angle and projected area reduced significantly, but the spray tip penetration increased. Increasing the fuel temperature from 275 K to 325 K did not cause significant increase of the evaporating rate, but with further increase of the fuel temperature, the ethanol spray's evaporation became faster. The transition temperature at which the ethanol spray collapsed at atmospheric pressure was between 355 K and 360 K.
- 8 July 2014
- Published by International Association for Automation and Robotics in Construction (IAARC) in Proceedings of the 37th International Symposium on Automation and Robotics in Construction (isarc)
- Vol. 2014 Proce, 584-591
Prediction of NOx Vehicular Emissions Using On-Board Measurement and Chassis Dynamometer Testing
I.A.A.R.C. - International Association for Automation and Robotics in Construction Civil Engineering
- 8 July 2014
- Published by International Association for Automation and Robotics in Construction (IAARC) in Proceedings of the 37th International Symposium on Automation and Robotics in Construction (isarc)
- Vol. 2014 Proce, 584-591
Prediction of NOx Vehicular Emissions Using On-Board Measurement and Chassis Dynamometer Testing
I.A.A.R.C. - International Association for Automation and Robotics in Construction Civil Engineering
- 1 January 2014
- Published by Elsevier in Applied Thermal Engineering
- Vol. 62 (2) , 303-312
Modeling study of soot formation and oxidation in DI diesel engine using an improved soot model
- 1 January 2014
- Published by Elsevier in Applied Thermal Engineering
- Vol. 62 (2) , 303-312
Modeling study of soot formation and oxidation in DI diesel engine using an improved soot model