Dongfeng Ji
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dongfeng Ji has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Bo Zhang
University of Electronic Science and Technology of China
8 shared publications - Xiaodong Chen
Queen Mary University of London
4 shared publications Yong Fan
University of Electronic Science and Technology of China
4 shared publications- Yilin Yang
School of Electric Science and Engineering, University of Electronic Science and Technology of China, Chengdu, Sichuan, 611731 China
3 shared publications - Yong Fan
EHF Key Laboratory of Fundamental Science, School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu 611731, China
3 shared publications - Zhongqian Niu
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
3 shared publications
Latest Publications
- Open Access
- 1 October 2021
- Published by Office of Scientific and Technical Information (OSTI)
Vertical GaN PN Diodes for Grid Resiliency and Medium-Voltage Power Electronics.
- 1 October 2021
- Published by Office of Scientific and Technical Information (OSTI)
Open AccessVertical GaN PN Diodes for Grid Resiliency and Medium-Voltage Power Electronics.
- Open Access
- 17 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 74401-74412
Development of High Power 220 GHz Frequency Triplers Based on Schottky Diodes
In this paper, the development of two high power 220 GHz frequency triplers is proposed. The GaAs Schottky diodes with six nodes are applied to realize high efficiency 220 GHz tripler, while the application of GaN Schottky diodes with eight nodes is another attempt to improve power handling of the 220 GHz tripler. To reduce thermal effect of high power multipliers, the AlN substrates with high thermal conductivity are applied to provide better heat dissipation at the diode areas. A combination of electrical and thermal model of the Schottky diodes is established while the optimization of 220 GHz triplers are realized with 3D electromagnetic (EM) simulation and harmonic balanced simulation. Good agreement is achieved between the simulated results based on electro-thermal model and measured performances of the triplers. At room temperature, peak efficiency of the tripler based on GaAs Schottky diodes is 17.8%, while the maximum output of the tripler is 38.2 mW with 300 mW input power. As for the 220 GHz GaN Schottky diode tripler, measured results show that the maximum power handling is beyond 400 mW. The peak efficiency and maximum output are 4.7% and 18.4 mW, respectively. The proposed methods of developing high power multipliers can be applied in higher frequency band in the future.
- 17 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 74401-74412
Open AccessDevelopment of High Power 220 GHz Frequency Triplers Based on Schottky Diodes
In this paper, the development of two high power 220 GHz frequency triplers is proposed. The GaAs Schottky diodes with six nodes are applied to realize high efficiency 220 GHz tripler, while the application of GaN Schottky diodes with eight nodes is another attempt to improve power handling of the 220 GHz tripler. To reduce thermal effect of high power multipliers, the AlN substrates with high thermal conductivity are applied to provide better heat dissipation at the diode areas. A combination of electrical and thermal model of the Schottky diodes is established while the optimization of 220 GHz triplers are realized with 3D electromagnetic (EM) simulation and harmonic balanced simulation. Good agreement is achieved between the simulated results based on electro-thermal model and measured performances of the triplers. At room temperature, peak efficiency of the tripler based on GaAs Schottky diodes is 17.8%, while the maximum output of the tripler is 38.2 mW with 300 mW input power. As for the 220 GHz GaN Schottky diode tripler, measured results show that the maximum power handling is beyond 400 mW. The peak efficiency and maximum output are 4.7% and 18.4 mW, respectively. The proposed methods of developing high power multipliers can be applied in higher frequency band in the future.
- Open Access
- 12 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 31214-31226
Development of a Wideband 220-GHz Subharmonic Mixer Based on GaAs Monolithic Integration Technology
A wideband 220 GHz subharmonic mixer based on monolithic integration technology is proposed in this paper. It features 12 μm-thick GaAs membrane with anti-parallel Schottky diodes working at THz band monolithically integrated on the membrane. The optimization principles of low-parastics Schottky diodes and the fabrication process of GaAs MMIC membrane diodes are elaborated. To realize optimum performances of the mixer, the dimensions of the integrated diodes and the matching network are optimized with harmonic balance simulation and load-pull techniques. An IF low pass filter with compact microstrip resonance cell (CMRC) configuration and an improved perpendicular coax-to-microstrip connection are used to realize wide IF band. The measured results show that the single sideband (SSB) conversion loss of this mixer is less than 10.5 dB from 185 to 255 GHz with fixed IF of 1 GHz, while the double sideband (DSB) noise temperature is better than 1400 K in this frequency range. Using fixed local oscillator (LO) frequency of 110 GHz, the measured SSB conversion loss is 7.4 - 10.7 dB within 185 - 255 GHz, indicating the good performances of the mixer with IF from DC to 35 GHz. The GaAs monolithic integration technology provides an approach for massive manufacturing of identical circuits and the proposed mixer with wideband characteristics will be applied in 220 GHz imaging systems in the near future.
- 12 February 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 31214-31226
Open AccessDevelopment of a Wideband 220-GHz Subharmonic Mixer Based on GaAs Monolithic Integration Technology
A wideband 220 GHz subharmonic mixer based on monolithic integration technology is proposed in this paper. It features 12 μm-thick GaAs membrane with anti-parallel Schottky diodes working at THz band monolithically integrated on the membrane. The optimization principles of low-parastics Schottky diodes and the fabrication process of GaAs MMIC membrane diodes are elaborated. To realize optimum performances of the mixer, the dimensions of the integrated diodes and the matching network are optimized with harmonic balance simulation and load-pull techniques. An IF low pass filter with compact microstrip resonance cell (CMRC) configuration and an improved perpendicular coax-to-microstrip connection are used to realize wide IF band. The measured results show that the single sideband (SSB) conversion loss of this mixer is less than 10.5 dB from 185 to 255 GHz with fixed IF of 1 GHz, while the double sideband (DSB) noise temperature is better than 1400 K in this frequency range. Using fixed local oscillator (LO) frequency of 110 GHz, the measured SSB conversion loss is 7.4 - 10.7 dB within 185 - 255 GHz, indicating the good performances of the mixer with IF from DC to 35 GHz. The GaAs monolithic integration technology provides an approach for massive manufacturing of identical circuits and the proposed mixer with wideband characteristics will be applied in 220 GHz imaging systems in the near future.
- Open Access
- 20 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 22506-22514
Analysis of Welding Pad for Terahertz Hybrid Integrated Mixer
In this paper, the influence of the silver glue on circuit performance and the reasons for its formation are analyzed in a terahertz hybrid integrated mixer. A validation analysis was carried out in the 600 - 700 GHz band with the aid of simulation software. Then a terahertz hybrid integrated mixing circuit with large pads was proposed in order to reduce the influence of the silver glue. Through the comparison of simulation results, it can be seen that after using large pads, the silver glue used for connection mainly concentrated on pads, which cannot have a significant impact on the matching of the circuits. The use of large pads also to a certain extent eliminates the resonance effect caused by silver glue. A terahertz hybrid integrated mixer with large pads was processed, assembled and tested. The test results show that the conversion loss is less than 14 dB under an RF frequency of 600 - 667 GHz. The experiments prove good consistency between measured and predicted conversion loss of the mixer using large pads. The difference between the measured and predicted conversion loss is only within 1.8 dB.
- 20 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 8, 22506-22514
Open AccessAnalysis of Welding Pad for Terahertz Hybrid Integrated Mixer
In this paper, the influence of the silver glue on circuit performance and the reasons for its formation are analyzed in a terahertz hybrid integrated mixer. A validation analysis was carried out in the 600 - 700 GHz band with the aid of simulation software. Then a terahertz hybrid integrated mixing circuit with large pads was proposed in order to reduce the influence of the silver glue. Through the comparison of simulation results, it can be seen that after using large pads, the silver glue used for connection mainly concentrated on pads, which cannot have a significant impact on the matching of the circuits. The use of large pads also to a certain extent eliminates the resonance effect caused by silver glue. A terahertz hybrid integrated mixer with large pads was processed, assembled and tested. The test results show that the conversion loss is less than 14 dB under an RF frequency of 600 - 667 GHz. The experiments prove good consistency between measured and predicted conversion loss of the mixer using large pads. The difference between the measured and predicted conversion loss is only within 1.8 dB.
- Open Access
- 11 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 50007-50011
A 220-GHz Third-Harmonic Mixer Based on Balanced Structure and Hybrid Transmission Line
This paper proposes a novel 220-GHz third-harmonic mixer, which using a waveguide-fin-coplanar waveguide-microstrip line hybrid transmission line as the carrier circuit, based on the balanced structure and the co-directional diode pair. The hybrid transmission line is designed to allow the mixing signals to be input in the correct direction in order to achieve the third-harmonic mixing. Then, high isolation between the radio-frequency (RF) port and the local oscillator (LO) port is performed through the mode orthogonality of the balanced structure. The metal slots on the fin line are used as the matching network for the RF signal to enable the RF signal into the diode pair with low loss. The experimental test results show that the conversion loss of the third-harmonic mixer is better than 18.5 dB in the range of 210–230 GHz and has a tiny fluctuation in the broad range of intermediate frequency (IF).
- 11 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 7, 50007-50011
Open AccessA 220-GHz Third-Harmonic Mixer Based on Balanced Structure and Hybrid Transmission Line
This paper proposes a novel 220-GHz third-harmonic mixer, which using a waveguide-fin-coplanar waveguide-microstrip line hybrid transmission line as the carrier circuit, based on the balanced structure and the co-directional diode pair. The hybrid transmission line is designed to allow the mixing signals to be input in the correct direction in order to achieve the third-harmonic mixing. Then, high isolation between the radio-frequency (RF) port and the local oscillator (LO) port is performed through the mode orthogonality of the balanced structure. The metal slots on the fin line are used as the matching network for the RF signal to enable the RF signal into the diode pair with low loss. The experimental test results show that the conversion loss of the third-harmonic mixer is better than 18.5 dB in the range of 210–230 GHz and has a tiny fluctuation in the broad range of intermediate frequency (IF).
- Open Access
- 14 March 2019
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (6) , 3603-3611
A High-Efficiency 220 GHz Doubler Based on the Planar Schottky Varactor Diode
- 14 March 2019
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 48 (6) , 3603-3611
Open AccessA High-Efficiency 220 GHz Doubler Based on the Planar Schottky Varactor Diode
- 8 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 29 (4) , 273-275
A Novel 3-dB Waveguide Hybrid Coupler for Terahertz Operation
- 8 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 29 (4) , 273-275
A Novel 3-dB Waveguide Hybrid Coupler for Terahertz Operation
- 7 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 40 (5) , 780-783
A Novel 220-GHz GaN Diode On-Chip Tripler With High Driven Power
This paper presents our study on a high power 220GHz frequency tripler based on a pair of GaN planar Schottky barrier diode chain chips. In the proposed frequency tripler, the pair of diode chips was directly mounted across the metal diaphragm in parallel with the opposite polarisation inside the rectangular waveguide. The RF field is tuned to its hot-spot, coupling directly onto the diode chains, turning on a diode chain at a time in an alternative manner. Unlike the traditional ones, in order to achieve a better heat dissipation, the diodes are directly connected with the metal block. Benefitting from a better heat dissipation and the power endure capacity of GaN material, the proposed tripler can work well under a watt level input power. The simulated tripler frequency conversion performance agrees with the measurement results very well. In addition, the experiments show that the frequency tripler can endure a maximum input power of 1.1W. And the output power of this frequency tripler is 17.5mW at 219.5GHz driven by 900mW input power with the best efficiency of 1.93%.
- 7 March 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 40 (5) , 780-783
A Novel 220-GHz GaN Diode On-Chip Tripler With High Driven Power
This paper presents our study on a high power 220GHz frequency tripler based on a pair of GaN planar Schottky barrier diode chain chips. In the proposed frequency tripler, the pair of diode chips was directly mounted across the metal diaphragm in parallel with the opposite polarisation inside the rectangular waveguide. The RF field is tuned to its hot-spot, coupling directly onto the diode chains, turning on a diode chain at a time in an alternative manner. Unlike the traditional ones, in order to achieve a better heat dissipation, the diodes are directly connected with the metal block. Benefitting from a better heat dissipation and the power endure capacity of GaN material, the proposed tripler can work well under a watt level input power. The simulated tripler frequency conversion performance agrees with the measurement results very well. In addition, the experiments show that the frequency tripler can endure a maximum input power of 1.1W. And the output power of this frequency tripler is 17.5mW at 219.5GHz driven by 900mW input power with the best efficiency of 1.93%.
- 17 November 2017
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 32 (5) , 579-590
Wide stopband millimeter/terahertz lowpass filter using improved split ring resonator
In this paper, an improved split-ring resonator (ISRR) cell is proposed to realize wide stopband and miniaturization. This cell comprises a transverse microstrip branch in middle and two gaps on both sides with tapped-line input and output. The transmission coefficient is derived for ISRR based on the distributed circuit theory and odd-even mode theory. Then the novel low-pass filter (LPF) is designed by cascading several ISRR cells in terahertz and millimeter. The ISRR LPF possesses great characteristics such as wide stopband, deep transmission zeros and small size. Finally, the proposed filter was processed and tested in millimeter. The measured results show that the proposed filter has low insertion loss from 0.5 to 0.7 dB in U-band and a stopband inhibition at 31.7 dB in 110 GHz.
- 17 November 2017
- Published by Taylor & Francis in Journal of Electromagnetic Waves and Applications
- Vol. 32 (5) , 579-590
Wide stopband millimeter/terahertz lowpass filter using improved split ring resonator
In this paper, an improved split-ring resonator (ISRR) cell is proposed to realize wide stopband and miniaturization. This cell comprises a transverse microstrip branch in middle and two gaps on both sides with tapped-line input and output. The transmission coefficient is derived for ISRR based on the distributed circuit theory and odd-even mode theory. Then the novel low-pass filter (LPF) is designed by cascading several ISRR cells in terahertz and millimeter. The ISRR LPF possesses great characteristics such as wide stopband, deep transmission zeros and small size. Finally, the proposed filter was processed and tested in millimeter. The measured results show that the proposed filter has low insertion loss from 0.5 to 0.7 dB in U-band and a stopband inhibition at 31.7 dB in 110 GHz.