JTJuuso Terva

Juuso Terva

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Juuso Terva has a total of 11 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    The effects of defect size and shape on fatigue response of large steel castings

    by Mira Adolfsson, Matti Isakov, Juuso Terva, Mikko Hokka

    The fatigue life of a cast component depends on the size of the component, residual stress states, loading and the microstructure of the material and especially the existence of defect structures, such as shrinkage porosity. Murakami’s equation for stress intensity factor (SIF) range (√𝑎𝑟𝑒𝑎-model) assumes that defects act as cracks, and the SIF can be calculated simply by determining the cross-sectional area of the defect. This model has been proven to work well for small defects like inclusions. However, shrinkage porosity in large steel cast components has usually very arbitrary shape and the size of a single defect can be large compared to the stressed volume. Therefore, the stress intensity factor range can vary significantly inside a large defect, and it is not immediately evident whether Murakami’s equation is applicable in these cases. In this study, one series of large specimens and two series of small specimens were investigated in rotating beam fatigue loading to study the effects of large casting defects on the high cycle fatigue life of large cast components. The fracture surfaces were examined with stereo and electron microscope to identify the source of the fatigue cracks. The stress intensity factors of selected large defects were further investigated with finite element method (FEM) analysis. For comparison the SIFs were also calculated with the analytical solution for almond shaped crack. The SIFs calculated with the Murakami’s equation for fatigue crack nucleation points were plotted against number of cycles to failure, and as a result, the defects divided into different groups based on their square root of area. This indicates that either the defect type and surrounding microstructure or the defect shape has an effect on the SIF range versus fatigue life dependency. The latter effect, i.e., the limitations of Murakami’s equation in the case of large arbitrarily shaped cracks, was further studied in this work. First the stress gradient was considered in the SIF calculations but it didn’t explain the division of the defects into different groups. Then selected defects were modelled as an elliptical arc in FEM to investigate the SIF values further. The FEM simulation results were comparable with the Murakami’s √𝑎𝑟𝑒𝑎-model and with the analytical solution for almond shaped crack. Thus, it was concluded that the geometrical shape of the defect did not have a clear effect on the fatigue life in the conducted tests. Therefore, more work is needed on the possible microstructural differences between the defects of varying sizes.

  • Correlation of wear and work in dual pivoted jaw crusher tests

    by Juuso Terva, Kati Valtonen, Pekka Siitonen, Veli-Tapani Kuokkala

    A laboratory sized jaw crusher with uniform movement of the jaws, the dual pivoted jaw crusher, was used to determine the relationship between wear and work. Wear was concentrated on the jaw plates opposing each other and was measured as mass loss of the specimens. Work was measured directly from the force and displacement of the instrumented jaw, which allowed work to accumulate only from the actual crushing events. The tests were conducted with several jaw geometries and with two motional settings, where the relation of compressive and sliding motion between the jaws was varied. The tests showed that the relation between wear and work was constant in many of the tested cases. In certain tests with larger lateral and faster contact speed, wear occurred at relatively lower amounts of work. This behavior was more definite when the relation of wear and work was investigated using modified Archards wear equation. The results indicate that the lower amount of needed work could stem from the material reaching a dynamic situation, where the flow stress becomes increasingly strain-rate dependent.


  • Effect of Multiple Impacts on the Deformation of Wear-Resistant Steels

    by Vilma Ratia, Harald Rojacz, Juuso Terva, Kati Valtonen, Ewald Badisch, Veli-Tapani Kuokkala


  • Abrasive wear of steel against gravel with different rock–steel combinations

    by Juuso Terva, Tuomas Teeri, Veli-Tapani Kuokkala, Pekka Siitonen, Jari Liimatainen