Feng Guo
Feng Guo has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Martin Collier
School of Electronic Engineering, Dublin City University, Dublin 9, Ireland
2 shared publications - Xiaojun Wang
Dublin City University
2 shared publications - Changli Zhao
State Key Lab of Metal Matrix Composites, School of Materials Science and Engineering, Shanghai Key Laboratory for Molecular Engineering of Chiral Drugs Shanghai Jiao Tong University Shanghai China
1 shared publication Jia-Yan Mao
Shijiazhuang Rail Transit Group Co., Ltd. (China)
1 shared publicationLuigi Sambolino
University of Genoa
1 shared publicationMei Song
Beijing University of Posts and Telecommunications
1 shared publication
Latest Publications
- Open Access
- 7 October 2023
- Published by Atlantis Press SARL
- p. 1749-1756
Research Review on Mechanical Properties of Segmental Assembled Bridge Joints
- 7 October 2023
- Published by Atlantis Press SARL
- p. 1749-1756
Open AccessResearch Review on Mechanical Properties of Segmental Assembled Bridge Joints
- 16 June 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12639, 511-515
Research on lattice model of inclined small box girder bridge based on frequency test method
The transverse stiffness simulation method of assembled small box girder bridge directly affects the internal force distribution of the structure. However, the lattice model of inclined small box girder bridge is seldom studied. In this paper, three box girder bridges with different diagonal angles of 25 m span are taken as the object, and different transverse stiffness simulation methods are used to calculate the natural vibration frequency of the bridges. The results are compared with the measured results. The results show that the beam end stiffness simulation method is most close to the measured results, and the roof section simulation lateral stiffness is much different from the measured results.
- 16 June 2023
- Published by SPIE-Intl Soc Optical Eng
- Vol. 12639, 511-515
Research on lattice model of inclined small box girder bridge based on frequency test method
The transverse stiffness simulation method of assembled small box girder bridge directly affects the internal force distribution of the structure. However, the lattice model of inclined small box girder bridge is seldom studied. In this paper, three box girder bridges with different diagonal angles of 25 m span are taken as the object, and different transverse stiffness simulation methods are used to calculate the natural vibration frequency of the bridges. The results are compared with the measured results. The results show that the beam end stiffness simulation method is most close to the measured results, and the roof section simulation lateral stiffness is much different from the measured results.
- Open Access
Greening the NetFPGA Reference Router
Energy efficiency is an important criterion in the design of next generation networks for both economic and environmental concerns. This paper presents an energy-efficient router that is able to dynamically adapt its routing capability in response to real-time traffic load, achieving energy proportional routing. The NetFPGA reference router, which operates at one of two frequencies (125 MHz or 62.5 MHz), requires a board reset to switch frequencies. We have modified the reference router to allow dynamic switching among five operating frequencies. Experiments with real traces indicate that, compared to the reference router, a 10% power reduction can be achieved through dynamic frequency scaling. When the router is further modified to support green traffic engineering and Ethernet port shut-down, power consumption can be reduced by 46% while maintaining the required quality of service. This allows the router to meet the instantaneous performance requirements while minimizing power dissipation. Similar results can be expected when these general power-saving principles are applied in future commercial routers.
Open AccessGreening the NetFPGA Reference Router
Energy efficiency is an important criterion in the design of next generation networks for both economic and environmental concerns. This paper presents an energy-efficient router that is able to dynamically adapt its routing capability in response to real-time traffic load, achieving energy proportional routing. The NetFPGA reference router, which operates at one of two frequencies (125 MHz or 62.5 MHz), requires a board reset to switch frequencies. We have modified the reference router to allow dynamic switching among five operating frequencies. Experiments with real traces indicate that, compared to the reference router, a 10% power reduction can be achieved through dynamic frequency scaling. When the router is further modified to support green traffic engineering and Ethernet port shut-down, power consumption can be reduced by 46% while maintaining the required quality of service. This allows the router to meet the instantaneous performance requirements while minimizing power dissipation. Similar results can be expected when these general power-saving principles are applied in future commercial routers.
- 1 May 2016
- Published by Springer Nature
- p. 104-115
Green Precision Time Protocol Router Using Dynamic Frequency Scaling
- 1 May 2016
- Published by Springer Nature
- p. 104-115
Green Precision Time Protocol Router Using Dynamic Frequency Scaling