William Ion
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
William Ion has a total of 70 co-authors. Here are the top co-authors by number of shared publications:
- Andrew Wodehouse
University of Strathclyde
10 shared publications Neal Juster
University of Glasgow
4 shared publicationsAngela Stone
University of Strathclyde, Scotland
3 shared publicationsAvril Thomson
University of Strathclyde, Scotland
3 shared publicationsDavid Nicol
University of Strathclyde
3 shared publicationsHilary Grierson
University of Strathclyde, Glasgow, Scotland, UK
3 shared publications
Latest Publications
- Open Access
- 9 March 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (6) , 3221
A Novel Approach towards Sustainability Assessment in Manufacturing and Stakeholder’s Role
With increasing consumer awareness about sustainability and governmental policies to address environmental challenges and social responsibility, the manufacturing sector is under continuous pressure to adopt more sustainable practices. Trends show that factories of the future (FOF) will need to adapt to market demands, growing economic and ecological efficiency requirements, and corporate social responsibility; such versatility is vital to address consumer disquiet and sustainability expectations. Various approaches have been proposed to assess sustainability over the last few decades. Most of these approaches have limitations in that they are of marginal relevance to the manufacturing environment, tend to focus on only one aspect of sustainability, or are too complicated for most organisations to implement. Moreover, numerous studies have demonstrated a gap in sustainability expectations among various stakeholders, and no active mechanisms exist to prioritise sustainability in manufacturing. This paper introduced a novel approach to address both the manufacturer and multiple stakeholders’ expectations about sustainability prioritisations in manufacturing practices. It achieved this using a modified quality function deployment (QFD) tool along with AHP and normalisation techniques. A set of system boundaries was adopted to evaluate sustainability in the manufacturing context; this research was a ‘Gate to Gate’ border. These indicators and a score-based approach will help organisations better grasp how manufacturing operations interact with sustainability and decision-making. They will help lead to improvements in the allocation of corporate resources used to manage and improve sustainability performance in manufacturing.
- 9 March 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (6) , 3221
Open AccessA Novel Approach towards Sustainability Assessment in Manufacturing and Stakeholder’s Role
With increasing consumer awareness about sustainability and governmental policies to address environmental challenges and social responsibility, the manufacturing sector is under continuous pressure to adopt more sustainable practices. Trends show that factories of the future (FOF) will need to adapt to market demands, growing economic and ecological efficiency requirements, and corporate social responsibility; such versatility is vital to address consumer disquiet and sustainability expectations. Various approaches have been proposed to assess sustainability over the last few decades. Most of these approaches have limitations in that they are of marginal relevance to the manufacturing environment, tend to focus on only one aspect of sustainability, or are too complicated for most organisations to implement. Moreover, numerous studies have demonstrated a gap in sustainability expectations among various stakeholders, and no active mechanisms exist to prioritise sustainability in manufacturing. This paper introduced a novel approach to address both the manufacturer and multiple stakeholders’ expectations about sustainability prioritisations in manufacturing practices. It achieved this using a modified quality function deployment (QFD) tool along with AHP and normalisation techniques. A set of system boundaries was adopted to evaluate sustainability in the manufacturing context; this research was a ‘Gate to Gate’ border. These indicators and a score-based approach will help organisations better grasp how manufacturing operations interact with sustainability and decision-making. They will help lead to improvements in the allocation of corporate resources used to manage and improve sustainability performance in manufacturing.
- 1 April 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 64, 1013-1023
Experimental Investigation of Plasma Cutting Two Separate Thin Steel Sheets Simultaneously and Parameters Optimisation Using Taguchi Approach
- 1 April 2021
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 64, 1013-1023
Experimental Investigation of Plasma Cutting Two Separate Thin Steel Sheets Simultaneously and Parameters Optimisation Using Taguchi Approach
- Open Access
- 2 October 2018
- Published by Springer Nature in Journal of Remanufacturing
- Vol. 9 (2) , 129-139
Low cost three-dimensional virtual model construction for remanufacturing industry
- 2 October 2018
- Published by Springer Nature in Journal of Remanufacturing
- Vol. 9 (2) , 129-139
Open AccessLow cost three-dimensional virtual model construction for remanufacturing industry
- Open Access
- 19 February 2018
- Published by Wiley in Creativity and Innovation Management
- Vol. 27 (1) , 91-101
Evolving improvised ideation from humour constructs: A new method for collaborative divergence
This paper reviews and applies key principles from improvised comedy (“improv”) to overcome common barriers in effective group ideation, resulting in the formulation and presentation of a new creative idea generation method. The emergence of an innovative product design can be compared to the telling of a funny joke: both combine seemingly unconnected ideas in a way that is both surprising and satisfying. Our research expands upon this link between humour and creativity, and operationalizes the improv principles best suited to the conceptual design process. A workshop‐based methodology was used to select, develop, and refine the method protocol and facilitation technique. Participant feedback and observations have demonstrated how this approach can expand the solution space to support the generation of bold, innovative ideas. Finally, we present a step‐by‐step guide for the new “design improv” method and discuss its potential value in the generation of creative ideas in a group ideation context.
- 19 February 2018
- Published by Wiley in Creativity and Innovation Management
- Vol. 27 (1) , 91-101
Open AccessEvolving improvised ideation from humour constructs: A new method for collaborative divergence
This paper reviews and applies key principles from improvised comedy (“improv”) to overcome common barriers in effective group ideation, resulting in the formulation and presentation of a new creative idea generation method. The emergence of an innovative product design can be compared to the telling of a funny joke: both combine seemingly unconnected ideas in a way that is both surprising and satisfying. Our research expands upon this link between humour and creativity, and operationalizes the improv principles best suited to the conceptual design process. A workshop‐based methodology was used to select, develop, and refine the method protocol and facilitation technique. Participant feedback and observations have demonstrated how this approach can expand the solution space to support the generation of bold, innovative ideas. Finally, we present a step‐by‐step guide for the new “design improv” method and discuss its potential value in the generation of creative ideas in a group ideation context.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1960 (1) , 110010
Optimising mechanical properties of hot forged nickel superalloy 625 components
Hot forging and subsequent heat treatment were resulting in substandard mechanical properties of nickel superalloy, Alloy 625, components. The low strength was found to be due to inadequate deformation during forging, excessive grain growth and precipitation of carbides during subsequent heat treatment. Experimentation in a drop forging company and heat treatment facility led to the establishment of optimal parameters to minimise grain size and mitigate the adverse effects of carbide precipitation, leading to successful fulfilment of mechanical property specifications. This was achieved by reducing the number of operations, maximising the extent of deformation by changing the slug dimensions and its orientation in the die, and minimising the time of exposure to elevated temperatures in both the forging and subsequent heat treatment processes to avoid grain growth.
- 1 January 2018
- Published by AIP Publishing in AIP Conference Proceedings
- Vol. 1960 (1) , 110010
Optimising mechanical properties of hot forged nickel superalloy 625 components
Hot forging and subsequent heat treatment were resulting in substandard mechanical properties of nickel superalloy, Alloy 625, components. The low strength was found to be due to inadequate deformation during forging, excessive grain growth and precipitation of carbides during subsequent heat treatment. Experimentation in a drop forging company and heat treatment facility led to the establishment of optimal parameters to minimise grain size and mitigate the adverse effects of carbide precipitation, leading to successful fulfilment of mechanical property specifications. This was achieved by reducing the number of operations, maximising the extent of deformation by changing the slug dimensions and its orientation in the die, and minimising the time of exposure to elevated temperatures in both the forging and subsequent heat treatment processes to avoid grain growth.
- Open Access
- 1 February 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 179 (1) , 012011
Automated microstructural analysis of titanium alloys using digital image processing
Titanium is a material that exhibits many desirable properties including a very high strength to weight ratio and corrosive resistance. However, the specific properties of any components depend upon the microstructure of the material, which varies by the manufacturing process. This means it is often necessary to analyse the microstructure when designing new processes or performing quality assurance on manufactured parts. For Ti6Al4V, grain size analysis is typically performed manually by expert material scientists as the complicated microstructure of the material means that, to the authors knowledge, no existing software reliably identifies the grain boundaries. This manual process is time consuming and offers low repeatability due to human error and subjectivity. In this paper, we propose a new, automated method to segment microstructural images of a Ti6Al4V alloy into its constituent grains and produce measurements. The results of applying this technique are evaluated by comparing the measurements obtained by different analysis methods. By using measurements from a complete manual segmentation as a benchmark we explore the reliability of the current manual estimations of grain size and contrast this with improvements offered by our approach.
- 1 February 2017
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 179 (1) , 012011
Open AccessAutomated microstructural analysis of titanium alloys using digital image processing
Titanium is a material that exhibits many desirable properties including a very high strength to weight ratio and corrosive resistance. However, the specific properties of any components depend upon the microstructure of the material, which varies by the manufacturing process. This means it is often necessary to analyse the microstructure when designing new processes or performing quality assurance on manufactured parts. For Ti6Al4V, grain size analysis is typically performed manually by expert material scientists as the complicated microstructure of the material means that, to the authors knowledge, no existing software reliably identifies the grain boundaries. This manual process is time consuming and offers low repeatability due to human error and subjectivity. In this paper, we propose a new, automated method to segment microstructural images of a Ti6Al4V alloy into its constituent grains and produce measurements. The results of applying this technique are evaluated by comparing the measurements obtained by different analysis methods. By using measurements from a complete manual segmentation as a benchmark we explore the reliability of the current manual estimations of grain size and contrast this with improvements offered by our approach.
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 716, 719-727
Investigation into the Numerical Model Behaviour of Belleville Washers in Cold Roll Forming
With the steady increase in demand for roll formed products, due to their application in fields such as automotive, construction, architecture, etc., roll forming companies are challenged with rising customer demands. Companies are struggling to bring a product through from design to manufacture at improved rates, whilst achieving tighter tolerances. The roll forming process may also induce undesirable forming defects such as twist, distortion and straightness problems. Over the years, numerical simulations have been deployed to assist with the geometric validation of these effects. For the purpose of this paper, an investigation shall focus on an individual parameter within the finite element analysis of the cold roll forming process, i.e. the ’unknown’ spring effect acting of the top roll during the forming process due to the implementation of Belleville washers in the pillar set up. This parameter is assessed over a range of applied loads and compared with a standard friction model with fixed top and bottom rolls. The longitudinal strains on the final profile, the geometric accuracy and thickness variation are observed and presented in this paper. Reasoning is also provided to explain why the final profile bows in the vertical direction.
- 1 October 2016
- Published by Trans Tech Publications, Ltd. in Key Engineering Materials
- Vol. 716, 719-727
Investigation into the Numerical Model Behaviour of Belleville Washers in Cold Roll Forming
With the steady increase in demand for roll formed products, due to their application in fields such as automotive, construction, architecture, etc., roll forming companies are challenged with rising customer demands. Companies are struggling to bring a product through from design to manufacture at improved rates, whilst achieving tighter tolerances. The roll forming process may also induce undesirable forming defects such as twist, distortion and straightness problems. Over the years, numerical simulations have been deployed to assist with the geometric validation of these effects. For the purpose of this paper, an investigation shall focus on an individual parameter within the finite element analysis of the cold roll forming process, i.e. the ’unknown’ spring effect acting of the top roll during the forming process due to the implementation of Belleville washers in the pillar set up. This parameter is assessed over a range of applied loads and compared with a standard friction model with fixed top and bottom rolls. The longitudinal strains on the final profile, the geometric accuracy and thickness variation are observed and presented in this paper. Reasoning is also provided to explain why the final profile bows in the vertical direction.
- 1 February 2013
- Published by Taylor & Francis in Journal of Engineering Design
- Vol. 24 (2) , 140-164
Enhancing the design dialogue: an architecture to document engineering design activities
This paper charts the development of a system architecture designed to address the challenges associated with creating accurate and re-usable records of synchronous design activities. It begins by describing the context of through-life support of engineering products, then presents the Knowledge Enhanced Notes system development work undertaken and provides direction for future research work in this area. An empirical research approach was adopted for this work incorporating 11 experimental episodes, ethnographic studies and case-based evaluation of the developed system. The approach and development of the system architecture within this research build upon and extend existing research in the area of knowledge and information capture. The proposed system architecture is proven to enhance the record of engineering design activities, demonstrating that the implementation of software-based tools can have a positive impact on the creation of a more accurate and complete record of activities. This research is focused on one category of design activities – synchronous; therefore, future research that focuses on asynchronous working, leading to an overall enhancement of design working, is needed. While the focus of the research was to aid the creation and through-life support of large, complex engineering products, the solution is entirely generic in its application to synchronous activities.
- 1 February 2013
- Published by Taylor & Francis in Journal of Engineering Design
- Vol. 24 (2) , 140-164
Enhancing the design dialogue: an architecture to document engineering design activities
This paper charts the development of a system architecture designed to address the challenges associated with creating accurate and re-usable records of synchronous design activities. It begins by describing the context of through-life support of engineering products, then presents the Knowledge Enhanced Notes system development work undertaken and provides direction for future research work in this area. An empirical research approach was adopted for this work incorporating 11 experimental episodes, ethnographic studies and case-based evaluation of the developed system. The approach and development of the system architecture within this research build upon and extend existing research in the area of knowledge and information capture. The proposed system architecture is proven to enhance the record of engineering design activities, demonstrating that the implementation of software-based tools can have a positive impact on the creation of a more accurate and complete record of activities. This research is focused on one category of design activities – synchronous; therefore, future research that focuses on asynchronous working, leading to an overall enhancement of design working, is needed. While the focus of the research was to aid the creation and through-life support of large, complex engineering products, the solution is entirely generic in its application to synchronous activities.
- 1 January 2013
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 213 (1) , 111-119
Identifying the dominant failure mode in the hot extrusion tooling used to forge nickel based superalloy
- 1 January 2013
- Published by Elsevier in Journal of Materials Processing Technology
- Vol. 213 (1) , 111-119
Identifying the dominant failure mode in the hot extrusion tooling used to forge nickel based superalloy
- Open Access
- 9 April 2011
- Published by Springer Nature in Research in Engineering Design
- Vol. 23 (1) , 5-15
Augmenting the 6-3-5 method with design information
- 9 April 2011
- Published by Springer Nature in Research in Engineering Design
- Vol. 23 (1) , 5-15
Open AccessAugmenting the 6-3-5 method with design information