Gareth Bradley
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Gareth Bradley has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
D. G. Hattingh
Department of Mechanical Engineering, PE Technikon, Private Bag X6011, Port Elizabeth 6001, South Africa
2 shared publications- Malcolm Neil James
University of Plymouth, UK
2 shared publications Andrew Norbury
Liverpool John Moores University
1 shared publicationD. J. Hughes
FaME38 at ILL-ESRF, 6 rue Jules Horowitz—BP156, 38042 Grenoble Cedex 9, France
1 shared publicationD.G. Hattingh
Nelson Mandela Metropolitan University
1 shared publicationD.J. Hughes
FaME38 at ILL-ESRF
1 shared publication
Latest Publications
- 25 January 2013
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 652-654, 1307-1310
Analysis of Indentation Size Effect of Vickers Hardness Tests of Steels
In this work, the indentation size effect (ISE) in Vickers hardness tests of steel with selected heat treatments (annealed or tempered) has been investigated and analysed. Systematical hardness tests were performed within a commonly used micro-load range. The experimental data was analysed according to the Meyer power-law and the proportional specimen resistance (PSR) models and the link between ISE and material properties was discussed. The results showed that the experimental data fitted well with the Mayers power-law (P = A.dn) and the PSR (P/d = al + a2d) models. The ISE index (n) showed a good correlation with the hardness-elastic modulus ratio (H/E), which potentially could be used to predict the relative contributions of the elastic and plastic deformation contact area under indentation load and to normalize the hardness values for inverse material properties .
- 25 January 2013
- Published by Trans Tech Publications, Ltd. in Advanced Materials Research
- Vol. 652-654, 1307-1310
Analysis of Indentation Size Effect of Vickers Hardness Tests of Steels
In this work, the indentation size effect (ISE) in Vickers hardness tests of steel with selected heat treatments (annealed or tempered) has been investigated and analysed. Systematical hardness tests were performed within a commonly used micro-load range. The experimental data was analysed according to the Meyer power-law and the proportional specimen resistance (PSR) models and the link between ISE and material properties was discussed. The results showed that the experimental data fitted well with the Mayers power-law (P = A.dn) and the PSR (P/d = al + a2d) models. The ISE index (n) showed a good correlation with the hardness-elastic modulus ratio (H/E), which potentially could be used to predict the relative contributions of the elastic and plastic deformation contact area under indentation load and to normalize the hardness values for inverse material properties .
- 1 February 2012
- Published by Elsevier in Computational Materials Science
- Vol. 52 (1) , 123-127
Numerical study of the mechanics of indentation bending tests of thin membranes and inverse materials parameters prediction
- 1 February 2012
- Published by Elsevier in Computational Materials Science
- Vol. 52 (1) , 123-127
Numerical study of the mechanics of indentation bending tests of thin membranes and inverse materials parameters prediction
- 1 October 2006
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 220 (4) , 181-187
Development of a novel metastable composite material
The development of a new family of mouldable metastable composite materials has been demonstrated. Their special quality is derived from the ability to maintain the matrix as a supercooled liquid or gel whose solidification can be triggered mechanically, as desired, by a user. This article describes some aspects of the development work. In particular, the following are explained: the choice of matrix material; the use of additives to enhance the properties of the matrix; and the selection of reinforcement fibre. As part of the work, some mechanical testing was performed on several variations of a matrix-fibre pair and, to demonstrate the potential of such materials, some comparisons were made with a possible competitor material, a glass-reinforced urethane. It was shown that the metastable material could be formulated to provide mechanical properties that would make it suitable for applications such as orthopaedic casting, splinting and body armour, and in items of sports equipment, these being areas where its mouldability could be particularly desirable.
- 1 October 2006
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
- Vol. 220 (4) , 181-187
Development of a novel metastable composite material
The development of a new family of mouldable metastable composite materials has been demonstrated. Their special quality is derived from the ability to maintain the matrix as a supercooled liquid or gel whose solidification can be triggered mechanically, as desired, by a user. This article describes some aspects of the development work. In particular, the following are explained: the choice of matrix material; the use of additives to enhance the properties of the matrix; and the selection of reinforcement fibre. As part of the work, some mechanical testing was performed on several variations of a matrix-fibre pair and, to demonstrate the potential of such materials, some comparisons were made with a possible competitor material, a glass-reinforced urethane. It was shown that the metastable material could be formulated to provide mechanical properties that would make it suitable for applications such as orthopaedic casting, splinting and body armour, and in items of sports equipment, these being areas where its mouldability could be particularly desirable.
- 17 September 2004
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 28 (1-2) , 245-256
The relationship between process mechanisms and crack paths in friction stir welded 5083‐H321 and 5383‐H321 aluminium alloys
Friction stir (FS) welding is a relatively new solid‐state welding process that offers high levels of joint performance with minimal preparation and little post‐weld dressing. The high levels of plastic work induced in the weld zone produce a very fine grain size in the stirred region of the weld (e.g. the nugget), while the low heat input limits residual stresses to a low fraction of the proof strength of the weld metal. These effects are generally beneficial to weld dynamic performance. The peculiar thermomechanical history in the FS weld region leads, however, to particular defects with some unusual effects on crack path, whose occurrence depends partly on crack speed, or growth rate. This paper presents observations regarding specific influences of the FS welding process on crack paths and dynamic performance for 5083‐H321 and 5383‐H321 aluminium alloys, and proposes an explanation for the observations in terms of the weld microstructures and thermomechanical history. The insights presented in this paper can be used to inform optimisation of the weld process parameters, through on‐line feedback and control of tool geometry, force footprint, torque and temperature.
- 17 September 2004
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 28 (1-2) , 245-256
The relationship between process mechanisms and crack paths in friction stir welded 5083‐H321 and 5383‐H321 aluminium alloys
Friction stir (FS) welding is a relatively new solid‐state welding process that offers high levels of joint performance with minimal preparation and little post‐weld dressing. The high levels of plastic work induced in the weld zone produce a very fine grain size in the stirred region of the weld (e.g. the nugget), while the low heat input limits residual stresses to a low fraction of the proof strength of the weld metal. These effects are generally beneficial to weld dynamic performance. The peculiar thermomechanical history in the FS weld region leads, however, to particular defects with some unusual effects on crack path, whose occurrence depends partly on crack speed, or growth rate. This paper presents observations regarding specific influences of the FS welding process on crack paths and dynamic performance for 5083‐H321 and 5383‐H321 aluminium alloys, and proposes an explanation for the observations in terms of the weld microstructures and thermomechanical history. The insights presented in this paper can be used to inform optimisation of the weld process parameters, through on‐line feedback and control of tool geometry, force footprint, torque and temperature.
- 20 February 2004
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 27 (3) , 187-202
Synchrotron diffraction measurement of residual stresses in friction stir welded 5383‐H321 aluminium butt joints and their modification by fatigue cycling
This paper presents two‐dimensional information on the residual stresses in 8 mm 5383‐H321 aluminium plates joined by double pass (DP) friction stir welding (FSW). It considers the inherent variability in residual stress magnitudes along 0.5 m lengths of weld pass, and their modification under a sequence of applied fatigue loads. This represents one of a planned series of experiments aimed at illuminating the effects of fatigue cycling on residual stress fields. In this particular case, the magnitudes of the bending fatigue loads (R= 0.1) were chosen to correlate with the measured proof strengths of the weld metal (approximately 160 MPa) and the parent plate (approximately 260–270 MPa). In four‐point bend S–N tests at R= 0.1 on 40 mm wide FS welded specimens of this alloy and plate thickness, these peak stress levels correspond to lives of around 105 cycles and 107 cycles, respectively. Results from the work indicate that significant variability exists among welded plates in peak compressive stress magnitudes (a range of perhaps −50 MPa to −140 MPa), although peak tensile stresses were relatively low and more consistent (from around 0 to 30 MPa). Fatigue loading accentuates the peak‐to‐valley stress change and causes an overall translation of the stresses to become more positive. Peak tensile stresses increase several‐fold during fatigue cycling.
- 20 February 2004
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 27 (3) , 187-202
Synchrotron diffraction measurement of residual stresses in friction stir welded 5383‐H321 aluminium butt joints and their modification by fatigue cycling
This paper presents two‐dimensional information on the residual stresses in 8 mm 5383‐H321 aluminium plates joined by double pass (DP) friction stir welding (FSW). It considers the inherent variability in residual stress magnitudes along 0.5 m lengths of weld pass, and their modification under a sequence of applied fatigue loads. This represents one of a planned series of experiments aimed at illuminating the effects of fatigue cycling on residual stress fields. In this particular case, the magnitudes of the bending fatigue loads (R= 0.1) were chosen to correlate with the measured proof strengths of the weld metal (approximately 160 MPa) and the parent plate (approximately 260–270 MPa). In four‐point bend S–N tests at R= 0.1 on 40 mm wide FS welded specimens of this alloy and plate thickness, these peak stress levels correspond to lives of around 105 cycles and 107 cycles, respectively. Results from the work indicate that significant variability exists among welded plates in peak compressive stress magnitudes (a range of perhaps −50 MPa to −140 MPa), although peak tensile stresses were relatively low and more consistent (from around 0 to 30 MPa). Fatigue loading accentuates the peak‐to‐valley stress change and causes an overall translation of the stresses to become more positive. Peak tensile stresses increase several‐fold during fatigue cycling.
- 15 August 2003
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 426-432, 2915-2920
Residual Stresses, Defects and Fatigue Cycling in Friction Stir Butt Welds in 5383-H321 and 5083-H321 Aluminium Alloys
- 15 August 2003
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 426-432, 2915-2920
Residual Stresses, Defects and Fatigue Cycling in Friction Stir Butt Welds in 5383-H321 and 5083-H321 Aluminium Alloys