Kee-Jeung Hong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kee-Jeung Hong has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
Sung Gook Cho
3 shared publications- Agha Syed Muhammad Gillani
School of Civil and Environmental Engineering, Kookmin University, Seoul 02707, Republic of Korea
2 shared publications - Chongku Yi
School of Civil, Environmental and Architectural Engineering, Korea University, Seoul 02841, Republic of Korea
2 shared publications Hyerin Lee
2 shared publications- Hyerin Lee
School of Civil and Environmental Engineering, Kookmin University, Seoul 02707, Korea
2 shared publications Minsoo Han
2 shared publications
Latest Publications
- Open Access
Effect of Low Corrosion Levels on the Bond Performance of Lap-Splices in Reinforced Concrete Beams
The Korean Highway Bridge Design Code introduced requirements for sufficient tensile lap-splice lengths in 2005. Bridge piers designed before 2005 might not have enough tensile lap-splice length. In addition to that, old structures are susceptible to corrosion due to several environmental factors. Thus, to investigate the effect of lap-splice lengths on the bending behavior of the old piers, twelve reinforced concrete (RC) beams were fabricated with sufficient and insufficient tensile lap-splice length, electrochemically corroded and tested under bending. Six of these beams, with sufficient lap-splice lengths, failed in a ductile manner after reinforcement bar (rebar) yielding occurred, whereas the remaining six, with insufficient lap-splice lengths, failed in a brittle manner owing to lap-splice bond failure before rebar yielding. The tested low-corrosion (< 4% by mass) beams exhibited significantly higher load-carrying capacities than non-corroded counterparts tested in our previous study. These results correlated with previously reported results by other researchers, indicating that low corrosion levels do not critically compromise the flexural performance of RC piers. Nevertheless, piers featuring insufficient lap-splice lengths must be rehabilitated to ensure seismically sufficient ductile flexural behavior.
Open AccessEffect of Low Corrosion Levels on the Bond Performance of Lap-Splices in Reinforced Concrete Beams
The Korean Highway Bridge Design Code introduced requirements for sufficient tensile lap-splice lengths in 2005. Bridge piers designed before 2005 might not have enough tensile lap-splice length. In addition to that, old structures are susceptible to corrosion due to several environmental factors. Thus, to investigate the effect of lap-splice lengths on the bending behavior of the old piers, twelve reinforced concrete (RC) beams were fabricated with sufficient and insufficient tensile lap-splice length, electrochemically corroded and tested under bending. Six of these beams, with sufficient lap-splice lengths, failed in a ductile manner after reinforcement bar (rebar) yielding occurred, whereas the remaining six, with insufficient lap-splice lengths, failed in a brittle manner owing to lap-splice bond failure before rebar yielding. The tested low-corrosion (< 4% by mass) beams exhibited significantly higher load-carrying capacities than non-corroded counterparts tested in our previous study. These results correlated with previously reported results by other researchers, indicating that low corrosion levels do not critically compromise the flexural performance of RC piers. Nevertheless, piers featuring insufficient lap-splice lengths must be rehabilitated to ensure seismically sufficient ductile flexural behavior.
- Open Access
- 15 February 2024
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 28 (5) , 1853-1872
Seismic Performance Management of Aged Road Facilities in Korea: Part 1 — Fragility Curves
- 15 February 2024
- Published by Elsevier in KSCE Journal of Civil Engineering
- Vol. 28 (5) , 1853-1872
Open AccessSeismic Performance Management of Aged Road Facilities in Korea: Part 1 — Fragility Curves
- Open Access
- 7 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (5) , 2748
Analysis of Adhesive Joints in a GFRP Bridge Deck under Bidirectional Bending Due to Traffic Wheel Loads
Glass-fiber-reinforced polymer (GFRP) decks have been widely used in the rehabilitation and construction of bridges as a replacement for conventional deck materials, such as steel, concrete, and wood. In this study, an analysis method for checking the local safety of joints in adhesively connected GFRP decks under bidirectional bending due to traffic wheel loads is newly presented. This method can be applied for designing and evaluating the joints of other FRP decks. The orthotropic material properties of the deck were approximately assumed according to the test results and previous research. Three-dimensional solid elements were used to simulate the local behavior of the adhesive and deck substrates at the joints. Global deflections of the deck and local deformations of the adhesive were evaluated for serviceability. The local stresses in the adhesive and deck substrate are evaluated at the joint to check for local failure modes of the joint under serviceability and ultimate limit states. The analysis results indicate that local failures of the adhesive and deck substrate at the joint occurred. Recommendations for avoiding these local failures and performing more precise analysis are suggested.
- 7 March 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (5) , 2748
Open AccessAnalysis of Adhesive Joints in a GFRP Bridge Deck under Bidirectional Bending Due to Traffic Wheel Loads
Glass-fiber-reinforced polymer (GFRP) decks have been widely used in the rehabilitation and construction of bridges as a replacement for conventional deck materials, such as steel, concrete, and wood. In this study, an analysis method for checking the local safety of joints in adhesively connected GFRP decks under bidirectional bending due to traffic wheel loads is newly presented. This method can be applied for designing and evaluating the joints of other FRP decks. The orthotropic material properties of the deck were approximately assumed according to the test results and previous research. Three-dimensional solid elements were used to simulate the local behavior of the adhesive and deck substrates at the joints. Global deflections of the deck and local deformations of the adhesive were evaluated for serviceability. The local stresses in the adhesive and deck substrate are evaluated at the joint to check for local failure modes of the joint under serviceability and ultimate limit states. The analysis results indicate that local failures of the adhesive and deck substrate at the joint occurred. Recommendations for avoiding these local failures and performing more precise analysis are suggested.
- Open Access
- 3 December 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (23) , 11454
An Innovative Steel Damper with a Flexural and Shear–Flexural Mechanism to Enhance the CBF System Behavior: An Experimental and Numerical Study
An innovative passive energy damper is introduced and studied experimentally and numerically. This damper is designed as the main plate for energy absorption which is surrounded by an octagon cover. In addition to simplicity in construction, it can be easily replaced after a severe earthquake. Experimental test results, as well as finite element results, indicated that, by connecting the cross-flexural plate to the main plate, the mechanism of the plate was changed from flexural to shear. However, the cross_flexural plate always acts as a flexural mechanism. Changing the shear mechanism to a flexural mechanism, on the other hand, increased the stiffness and strength, while it reduced the ultimate displacement. Comparing the hysteresis curve of specimens revealed that models without cross_flexural plates had less strength and energy_dissipating capability than other models. Adding the flexural plate to the damper without connecting to the main plate improved the behavior of the damper, mainly by improving the ultimate displacement. Connecting the cross plate to the web plate enhanced the ultimate strength and stiffness by 84% and 3.9, respectively, but it reduced the ductility by 2.25. Furthermore, relationships were proposed to predict the behavior of the dampers with high accuracy.
- 3 December 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (23) , 11454
Open AccessAn Innovative Steel Damper with a Flexural and Shear–Flexural Mechanism to Enhance the CBF System Behavior: An Experimental and Numerical Study
An innovative passive energy damper is introduced and studied experimentally and numerically. This damper is designed as the main plate for energy absorption which is surrounded by an octagon cover. In addition to simplicity in construction, it can be easily replaced after a severe earthquake. Experimental test results, as well as finite element results, indicated that, by connecting the cross-flexural plate to the main plate, the mechanism of the plate was changed from flexural to shear. However, the cross_flexural plate always acts as a flexural mechanism. Changing the shear mechanism to a flexural mechanism, on the other hand, increased the stiffness and strength, while it reduced the ultimate displacement. Comparing the hysteresis curve of specimens revealed that models without cross_flexural plates had less strength and energy_dissipating capability than other models. Adding the flexural plate to the damper without connecting to the main plate improved the behavior of the damper, mainly by improving the ultimate displacement. Connecting the cross plate to the web plate enhanced the ultimate strength and stiffness by 84% and 3.9, respectively, but it reduced the ductility by 2.25. Furthermore, relationships were proposed to predict the behavior of the dampers with high accuracy.
- Open Access
Local Behavior of Lap-Spliced Deformed Rebars in Reinforced Concrete Beams
Twelve full-scale reinforced concrete beams with two tension lap splices were constructed and tested under a four-point loading test. Half of these beams had shorter lap splices than that recommended by American Concrete Institute Building Code ACI 318-19; they failed by bond loss between steel and concrete at the lap splice region before rebar yielding. The other half of the beams were designed with a lap splice length slightly exceeding that recommended by ACI 318-19; they failed by rebar yielding and exhibited a ductile behavior. Several strain gauges were attached to the longitudinal bars in the lap splice region to study the local behavior of deformed bars during loading. The strain in a rebar was maximum at the loaded end of the lap splice and progressively decreased toward the unloaded end because the rebar at this end could not sustain any load. Stress flow discontinuity occurred at the loaded end and caused stress concentration. The effect of this concentration was investigated based on test results. The comparison of bond strengths calculated by existing equations and those of tested specimens indicated that the results agreed well.
Open AccessLocal Behavior of Lap-Spliced Deformed Rebars in Reinforced Concrete Beams
Twelve full-scale reinforced concrete beams with two tension lap splices were constructed and tested under a four-point loading test. Half of these beams had shorter lap splices than that recommended by American Concrete Institute Building Code ACI 318-19; they failed by bond loss between steel and concrete at the lap splice region before rebar yielding. The other half of the beams were designed with a lap splice length slightly exceeding that recommended by ACI 318-19; they failed by rebar yielding and exhibited a ductile behavior. Several strain gauges were attached to the longitudinal bars in the lap splice region to study the local behavior of deformed bars during loading. The strain in a rebar was maximum at the loaded end of the lap splice and progressively decreased toward the unloaded end because the rebar at this end could not sustain any load. Stress flow discontinuity occurred at the loaded end and caused stress concentration. The effect of this concentration was investigated based on test results. The comparison of bond strengths calculated by existing equations and those of tested specimens indicated that the results agreed well.
- Open Access
Effect of Low-Level Cyclic Loading on Bond Behavior of a Steel Bar in Concrete with Pre-Existing Damage
Understanding the bond behavior of steel rebar in concrete is important in order to determine the performance of a reinforced concrete structure. Although numerous studies have been carried out by many researchers to develop a robust model for numerical analysis, no consensus has been reached as the bond behavior depends on hysteresis. In this study, the bond behavior of a steel bar in concrete with pre-existing damage is investigated under low-level cyclic loading. Based on the experimental bond stress and slip curve, a numerical model for finite element analysis to simulate the effect of low-level cyclic loading is proposed. The results from the numerical analysis show good agreement with the experimental data, including accumulated damage on stiffness and strength throughout entire load cycles.
Open AccessEffect of Low-Level Cyclic Loading on Bond Behavior of a Steel Bar in Concrete with Pre-Existing Damage
Understanding the bond behavior of steel rebar in concrete is important in order to determine the performance of a reinforced concrete structure. Although numerous studies have been carried out by many researchers to develop a robust model for numerical analysis, no consensus has been reached as the bond behavior depends on hysteresis. In this study, the bond behavior of a steel bar in concrete with pre-existing damage is investigated under low-level cyclic loading. Based on the experimental bond stress and slip curve, a numerical model for finite element analysis to simulate the effect of low-level cyclic loading is proposed. The results from the numerical analysis show good agreement with the experimental data, including accumulated damage on stiffness and strength throughout entire load cycles.
- 28 February 2021
- Published by Korean Society for Advanced Composite Structures in Journal of the Korean Society for Advanced Composite Structures
- Vol. 12 (1) , 9-17
Effect of Composite Fiber Panels and Basalt-Based Fiber Reinforced Polymer Wrapping on the Seismic Behavior of Square Reinforced Concrete Columns
- 28 February 2021
- Published by Korean Society for Advanced Composite Structures in Journal of the Korean Society for Advanced Composite Structures
- Vol. 12 (1) , 9-17
Effect of Composite Fiber Panels and Basalt-Based Fiber Reinforced Polymer Wrapping on the Seismic Behavior of Square Reinforced Concrete Columns
- 31 March 2020
- Published by Earthquake Engineering Society of Korea in Journal of the Earthquake Engineering Society of Korea
- Vol. 24 (2) , 95-102
Rocking Stiffness of Electrical Cabinet for In-Cabinet Response Spectrum
- 31 March 2020
- Published by Earthquake Engineering Society of Korea in Journal of the Earthquake Engineering Society of Korea
- Vol. 24 (2) , 95-102
Rocking Stiffness of Electrical Cabinet for In-Cabinet Response Spectrum