Rob Thornton
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Rob Thornton has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Tom Slatter
Department of Mechanical Engineering, The University of Sheffield, Sheffield, UK
4 shared publications R. Lewis
University of Sheffield
2 shared publications- Shiladitya Paul
Materials Innovation Centre, School of Engineering, University of Leicester, Leicester LE1 7RH, UK
2 shared publications - Alan Hywel Jones
Materials and Engineering Research Institute Sheffield Hallam University Sheffield UK
1 shared publication Aude Cumont
1 shared publicationBasim M. A. Al Bhadle
Department of Engineering, University of Leicester, Leicester, UK
1 shared publication
Latest Publications
- Open Access
- 1 July 2021
- Published by Elsevier in Corrosion Science
- Vol. 187
Study of cathodic reactions in defects of thermal spray aluminium coatings on steel in artificial seawater
- 1 July 2021
- Published by Elsevier in Corrosion Science
- Vol. 187
Open AccessStudy of cathodic reactions in defects of thermal spray aluminium coatings on steel in artificial seawater
- 1 January 2020
- Published by Elsevier in Diamond and Related Materials
- Vol. 101
Subsurface cleavage of diamond after high-speed three-dimensional dynamic friction polishing
- 1 January 2020
- Published by Elsevier in Diamond and Related Materials
- Vol. 101
Subsurface cleavage of diamond after high-speed three-dimensional dynamic friction polishing
- Open Access
- 26 March 2019
- Published by Wiley in Materials and Corrosion
- Vol. 70 (6) , 996-1004
Effect of seawater constituents on the performance of thermal spray aluminum in marine environments
Thermally sprayed coatings are often used to mitigate corrosion of offshore structures. They act as a physical barrier to the aggressive marine environment and as a sacrificial distributed anode for low carbon steel. In such environments, the severity of material degradation depends on many factors. The effect of temperature, exposure time or the presence of micro‐organisms are the focus of many studies, for example, however, the effect of the different ions present in seawater remains largely unexplored. The chemical composition of the water changes considerably depending on the location; industrial, glacial, estuarine, and so forth. In addition, when thermal spray aluminum (TSA) protects steel in seawater, calcareous matter precipitates as a result of the cathodic polarization and subsequent localized increase in pH. Therefore, understanding how ions such as magnesium (II), calcium (II), or carbonates alter the coating properties in the marine environment is important. This paper reports the experimental work carried out with TSA‐coated steel samples with defects to simulate mechanical damage or erosion of the coating. The combination of electrochemical tests and surface characterization provided evidence of the efficiency of the calcareous bilayer that forms on top of steel reducing the TSA degradation.
- 26 March 2019
- Published by Wiley in Materials and Corrosion
- Vol. 70 (6) , 996-1004
Open AccessEffect of seawater constituents on the performance of thermal spray aluminum in marine environments
Thermally sprayed coatings are often used to mitigate corrosion of offshore structures. They act as a physical barrier to the aggressive marine environment and as a sacrificial distributed anode for low carbon steel. In such environments, the severity of material degradation depends on many factors. The effect of temperature, exposure time or the presence of micro‐organisms are the focus of many studies, for example, however, the effect of the different ions present in seawater remains largely unexplored. The chemical composition of the water changes considerably depending on the location; industrial, glacial, estuarine, and so forth. In addition, when thermal spray aluminum (TSA) protects steel in seawater, calcareous matter precipitates as a result of the cathodic polarization and subsequent localized increase in pH. Therefore, understanding how ions such as magnesium (II), calcium (II), or carbonates alter the coating properties in the marine environment is important. This paper reports the experimental work carried out with TSA‐coated steel samples with defects to simulate mechanical damage or erosion of the coating. The combination of electrochemical tests and surface characterization provided evidence of the efficiency of the calcareous bilayer that forms on top of steel reducing the TSA degradation.
- Open Access
- 12 February 2019
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 50 (4) , 1748-1762
Getting the Strain Under Control: Trans-Varestraint Tests for Hot Cracking Susceptibility
A new method for conducting Trans-Varestraint tests for assessing hot cracking susceptibility is proposed. Experiments were carried out, to validate the new method, with an industrial scale rig using tungsten inert gas welding. The hot cracking susceptibility of API-5L X65 and EN3B steel was compared. The results indicated that, by using the new method, the strain applied to the welding bead and consequently to the solidification front was controlled in a repeatable and reliable way. The results also indicated that EN3B has a maximum crack length (a parameter in the test) higher than X65 and it is reached at lower augmented strain thus demonstrating it is more susceptible to hot cracking, while also indicating that there is a capability of predicting the initiation position of hot cracks during welding. By using the method proposed, the capability of setting standardized test procedures for Trans-Varestraint tests is improved. It is recommended that future tests for assessing hot cracking susceptibility should employ the proposed method in order for the results to be comparable and to also study the effect of strain rate in hot cracking of materials.
- 12 February 2019
- Published by Springer Nature in Metallurgical and Materials Transactions A
- Vol. 50 (4) , 1748-1762
Open AccessGetting the Strain Under Control: Trans-Varestraint Tests for Hot Cracking Susceptibility
A new method for conducting Trans-Varestraint tests for assessing hot cracking susceptibility is proposed. Experiments were carried out, to validate the new method, with an industrial scale rig using tungsten inert gas welding. The hot cracking susceptibility of API-5L X65 and EN3B steel was compared. The results indicated that, by using the new method, the strain applied to the welding bead and consequently to the solidification front was controlled in a repeatable and reliable way. The results also indicated that EN3B has a maximum crack length (a parameter in the test) higher than X65 and it is reached at lower augmented strain thus demonstrating it is more susceptible to hot cracking, while also indicating that there is a capability of predicting the initiation position of hot cracks during welding. By using the method proposed, the capability of setting standardized test procedures for Trans-Varestraint tests is improved. It is recommended that future tests for assessing hot cracking susceptibility should employ the proposed method in order for the results to be comparable and to also study the effect of strain rate in hot cracking of materials.
- 1 February 2019
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 24 (2) , 93-100
Equations of heat generation during friction stir welding for tapered polygonal tools
Owing to the complex nature of heat generation in friction stir welding, equations are required to understand the effect of process parameters and tool geometry on heat generation. In this study, simplified equations for straight tool profiles have been extended to treat tapered tool profiles for triangular, square, pentagonal and hexagonal geometries. New equations have been implemented to model heat generation in a finite element software package for welding aluminium alloy. The calculated thermal profiles agree better with experimental data than those calculated using the simplified equations. It was also demonstrated that the amount of heat generation increases with increasing number of flats on the tapered tool profile, with a hexagonal tapered tool profile generating the highest temperature.
- 1 February 2019
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 24 (2) , 93-100
Equations of heat generation during friction stir welding for tapered polygonal tools
Owing to the complex nature of heat generation in friction stir welding, equations are required to understand the effect of process parameters and tool geometry on heat generation. In this study, simplified equations for straight tool profiles have been extended to treat tapered tool profiles for triangular, square, pentagonal and hexagonal geometries. New equations have been implemented to model heat generation in a finite element software package for welding aluminium alloy. The calculated thermal profiles agree better with experimental data than those calculated using the simplified equations. It was also demonstrated that the amount of heat generation increases with increasing number of flats on the tapered tool profile, with a hexagonal tapered tool profile generating the highest temperature.
- 14 December 2013
- Published by Springer Nature in Production Engineering
- Vol. 8 (3) , 355-364
Effects of deep cryogenic treatment on the wear development of H13A tungsten carbide inserts when machining AISI 1045 steel
- 14 December 2013
- Published by Springer Nature in Production Engineering
- Vol. 8 (3) , 355-364
Effects of deep cryogenic treatment on the wear development of H13A tungsten carbide inserts when machining AISI 1045 steel