Andrea Tonti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrea Tonti has a total of 49 co-authors. Here are the top co-authors by number of shared publications:
- Francesco Rizzo
Sapienza University of Rome
3 shared publications - Fabio Giannetti
DIAEE Department, Sapienza University of Rome, 00186 Rome, Italy
2 shared publications - Loriana Ricciardi
INAIL-DIT-Sezione VI Supporto Tecnico UOT Via Roberto Ferruzzi, n.38/40, 00143 Roma, Italy
2 shared publications A. Alvino
Inail Innovative Technologies Department, Rome, Italy
1 shared publicationA. Antonini
Inail Innovative Technologies Department, Rome, Italy
1 shared publication- Adriano Marin
WOW Technology S.p.A., 35043 Monselice, Italy
1 shared publication
Latest Publications
- Open Access
- 23 June 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (13) , 6283
AI-Assisted Creep Time Prediction Using Creep Strain Curves of AISI 316 Austenitic Stainless Steel: Effects of Data Transformation and Hyperparameter Optimisation
High-temperature structural components are susceptible to creep deformation, which can ultimately lead to failure. In this work, an AI-based framework was developed capable of predicting the creep time of 316 austenitic stainless steel. Here, creep time refers to both the time to reach specific strain levels and the time to rupture. However, the scope of the present work is limited to rupture-time prediction, while the application of the framework to strain-level prediction will be reported in future work. The dataset consisted of creep strain curves from four heats, including both rupture and non-rupture curves. Random Forest (RF), Gradient Boosting (GB), Extreme Gradient Boosting (XGB), Support Vector Regressor (SVR), Gaussian Process Regressor (GPR), and Neural Network (NN) were employed. The effects of square-root and cube-root transformations on data distribution and model learning behaviour were analysed using model learning curves. An Optuna (version 4.3.0)-based hyperparameter tuning strategy was employed. The cube-root transformation improved the learning performance of SVR, GPR, and NN, whereas RF, GB, and XGB remained unaffected. Learning curves revealed mild overfitting for RF, GB, and XGB, and very minimal overfitting for SVR, GPR, and NN. NN achieved the best predictive performance (, deviation factor of 1.57). The findings demonstrated that the combined useof creep strain curves, data transformation, learning curve guided model selection, and rigorous hyperparameter tuning can improve the prediction accuracy under a limited dataset.- 23 June 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (13) , 6283
Open AccessAI-Assisted Creep Time Prediction Using Creep Strain Curves of AISI 316 Austenitic Stainless Steel: Effects of Data Transformation and Hyperparameter Optimisation
High-temperature structural components are susceptible to creep deformation, which can ultimately lead to failure. In this work, an AI-based framework was developed capable of predicting the creep time of 316 austenitic stainless steel. Here, creep time refers to both the time to reach specific strain levels and the time to rupture. However, the scope of the present work is limited to rupture-time prediction, while the application of the framework to strain-level prediction will be reported in future work. The dataset consisted of creep strain curves from four heats, including both rupture and non-rupture curves. Random Forest (RF), Gradient Boosting (GB), Extreme Gradient Boosting (XGB), Support Vector Regressor (SVR), Gaussian Process Regressor (GPR), and Neural Network (NN) were employed. The effects of square-root and cube-root transformations on data distribution and model learning behaviour were analysed using model learning curves. An Optuna (version 4.3.0)-based hyperparameter tuning strategy was employed. The cube-root transformation improved the learning performance of SVR, GPR, and NN, whereas RF, GB, and XGB remained unaffected. Learning curves revealed mild overfitting for RF, GB, and XGB, and very minimal overfitting for SVR, GPR, and NN. NN achieved the best predictive performance (, deviation factor of 1.57). The findings demonstrated that the combined useof creep strain curves, data transformation, learning curve guided model selection, and rigorous hyperparameter tuning can improve the prediction accuracy under a limited dataset. - 2 January 2026
- Published by Springer Nature
- p. 613-624
FEM Methodologies for the Simplified Thermal Analysis of Waste Package for ILW Radioactive Waste
- 2 January 2026
- Published by Springer Nature
- p. 613-624
FEM Methodologies for the Simplified Thermal Analysis of Waste Package for ILW Radioactive Waste
- 1 January 2025
- Published by Research Publishing Services
- p. 2625-2632
Innovative Solutions for the Management and Safety of Radioactive Waste
- 1 January 2025
- Published by Research Publishing Services
- p. 2625-2632
Innovative Solutions for the Management and Safety of Radioactive Waste
- 12 October 2023
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 41 (2) , 222-233
Steel grades 91 and 92 microstructure and precipitate evolution atlas and life assessment tool
- 12 October 2023
- Published by Taylor & Francis in Materials at High Temperatures
- Vol. 41 (2) , 222-233
Steel grades 91 and 92 microstructure and precipitate evolution atlas and life assessment tool
- Open Access
The New Italian Standard on the Life Assessment of Martensitic Steels—First Results of the Experimental Validation Activity of XRD by Testing P91 and P92 Samples from Interrupted Uniaxial Creep Tests
The Italian Thermotechnical Committee is drafting a new standard for the life assessment of creep-operated pressure equipment, including modern steam boilers. For the evaluation of the spent life ratio several methods are available, even if each of them is not exhaustive. It should be noted that the methods described must be considered in combination with NDTs and other kinds of tests, e.g., hardness tests. X-ray diffraction (XRD) is one of the methods that could be used to assess material evolution under creep conditions. The method allows for the study of phase transitions involving structural variations. It is possible to operate on both massive samples and powders. In this paper, work done with XRD, in the frame of a wider project regarding the study of the high-temperature behavior of welded martensitic steels, is presented. The results of the XRD analysis were compared with the results of the extraction replicas. This work concerns the controls of eight failed crept specimens submitted to XRD examinations. Eight XRD diagrams were produced and subsequently compared with 12 replicas for each specimen; that is, 96 extraction replicas were produced for this work. Then, around 5000 precipitates were analyzed for each specimen; therefore, for this work, around 40,000 precipitates were characterized with their chemical compositions. The average size of the precipitates was around 97 nm.
Open AccessThe New Italian Standard on the Life Assessment of Martensitic Steels—First Results of the Experimental Validation Activity of XRD by Testing P91 and P92 Samples from Interrupted Uniaxial Creep Tests
The Italian Thermotechnical Committee is drafting a new standard for the life assessment of creep-operated pressure equipment, including modern steam boilers. For the evaluation of the spent life ratio several methods are available, even if each of them is not exhaustive. It should be noted that the methods described must be considered in combination with NDTs and other kinds of tests, e.g., hardness tests. X-ray diffraction (XRD) is one of the methods that could be used to assess material evolution under creep conditions. The method allows for the study of phase transitions involving structural variations. It is possible to operate on both massive samples and powders. In this paper, work done with XRD, in the frame of a wider project regarding the study of the high-temperature behavior of welded martensitic steels, is presented. The results of the XRD analysis were compared with the results of the extraction replicas. This work concerns the controls of eight failed crept specimens submitted to XRD examinations. Eight XRD diagrams were produced and subsequently compared with 12 replicas for each specimen; that is, 96 extraction replicas were produced for this work. Then, around 5000 precipitates were analyzed for each specimen; therefore, for this work, around 40,000 precipitates were characterized with their chemical compositions. The average size of the precipitates was around 97 nm.
- Open Access
Microstructural Evolution of T91 in High Temperature Conditions and under Combined Effect of Stress and Temperature
ASTM A213 T91 steel is widely used in power plants and petrochemical industry for long-term service components. Due to its high resistance to creep, thermomechanical fatigue and corrosion, the use of grade 91 steel allows usual plant service parameters to be raised up to ultra-supercritical conditions (600 °C, 300 bar) so that performances are remarkably increased. The strongest factors that affect performances are the time of exposure, the temperature and the applied stress: such parameters can dramatically decrease the service life of a plant component. The improved mechanical properties of grade 91 are strictly related to its specific microstructure: a tempered martensite matrix with fine precipitates embedded in. Two typologies of secondary phases are present: M23C6 carbides (where M = Cr/Fe/Mo/Mn) and finely dispersed MX-type carbonitrides (where M = V/Nb and X = C/N). This study is focused on the microstructure evolution of grade 91 steel under creep conditions. First, three sets of laboratory-aged specimens heated in oven at 550 °C, 600 °C and 650 °C were examined; the exposure time was up to 50,000 h. Furthermore, the influence of stress on the microstructure in two sets of samples was evaluated: a first batch of specimens cut from an ex-service tube of a petrochemical plant (over 100,000 h of service at 580 °C and 19–25 bar) and a second set of samples coming from another ex-service tube under ultra-supercritical conditions (605 °C, 252 bar) in a power plant. The microstructures were characterized by optical, scanning electron and transmission electron microscopy and the results were compared to the literature. Some interesting trends were evidenced, in terms of secondary phases precipitation and coarsening, as well as martensite recovery. Furthermore, the applied stress seems to influence size and number of Laves phase particles.
Open AccessMicrostructural Evolution of T91 in High Temperature Conditions and under Combined Effect of Stress and Temperature
ASTM A213 T91 steel is widely used in power plants and petrochemical industry for long-term service components. Due to its high resistance to creep, thermomechanical fatigue and corrosion, the use of grade 91 steel allows usual plant service parameters to be raised up to ultra-supercritical conditions (600 °C, 300 bar) so that performances are remarkably increased. The strongest factors that affect performances are the time of exposure, the temperature and the applied stress: such parameters can dramatically decrease the service life of a plant component. The improved mechanical properties of grade 91 are strictly related to its specific microstructure: a tempered martensite matrix with fine precipitates embedded in. Two typologies of secondary phases are present: M23C6 carbides (where M = Cr/Fe/Mo/Mn) and finely dispersed MX-type carbonitrides (where M = V/Nb and X = C/N). This study is focused on the microstructure evolution of grade 91 steel under creep conditions. First, three sets of laboratory-aged specimens heated in oven at 550 °C, 600 °C and 650 °C were examined; the exposure time was up to 50,000 h. Furthermore, the influence of stress on the microstructure in two sets of samples was evaluated: a first batch of specimens cut from an ex-service tube of a petrochemical plant (over 100,000 h of service at 580 °C and 19–25 bar) and a second set of samples coming from another ex-service tube under ultra-supercritical conditions (605 °C, 252 bar) in a power plant. The microstructures were characterized by optical, scanning electron and transmission electron microscopy and the results were compared to the literature. Some interesting trends were evidenced, in terms of secondary phases precipitation and coarsening, as well as martensite recovery. Furthermore, the applied stress seems to influence size and number of Laves phase particles.
- Open Access
- 24 August 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (17) , 10565
Decontamination and Remediation of Underground Holes and Testing of Cleaning Techniques Based on the Use of Liquid Cold Decontaminant
As part of its institutional skills, the INAIL (National Institute for Insurance against Accidents at Work) promotes and carries out activities aimed at preventing the risks to which workers may be subjected to in different work scenarios, in this case, in collaboration with Livanova and WOW Technology S.p.A. (Wonderful Water Technology, Monselice, PD, Italy). An open problem at the Livanova plant, located in Saluggia (VC, Italy), is the decontamination of many concrete structures. Precisely because of its radioactive content, simple mechanical removal wasn’t possible for the high production of the contaminated dust, which may endanger the health of workers. The solution adopted was to insert decontaminant liquids into the concrete structures and, after a period of soaking, treating these liquids with an evaporative machine that is able to separate contaminants. The combination of these systems proved to be suitable for this experimental decontamination activity. As a result, this activity has shown a certain efficiency in removing radioactivity from the walls of the structures, ensuring the safety of the workers involved during the operations and reducing the potential risk of exposure in comparison to mechanical removal.
- 24 August 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (17) , 10565
Open AccessDecontamination and Remediation of Underground Holes and Testing of Cleaning Techniques Based on the Use of Liquid Cold Decontaminant
As part of its institutional skills, the INAIL (National Institute for Insurance against Accidents at Work) promotes and carries out activities aimed at preventing the risks to which workers may be subjected to in different work scenarios, in this case, in collaboration with Livanova and WOW Technology S.p.A. (Wonderful Water Technology, Monselice, PD, Italy). An open problem at the Livanova plant, located in Saluggia (VC, Italy), is the decontamination of many concrete structures. Precisely because of its radioactive content, simple mechanical removal wasn’t possible for the high production of the contaminated dust, which may endanger the health of workers. The solution adopted was to insert decontaminant liquids into the concrete structures and, after a period of soaking, treating these liquids with an evaporative machine that is able to separate contaminants. The combination of these systems proved to be suitable for this experimental decontamination activity. As a result, this activity has shown a certain efficiency in removing radioactivity from the walls of the structures, ensuring the safety of the workers involved during the operations and reducing the potential risk of exposure in comparison to mechanical removal.
- Open Access
- 1 July 2018
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 731, 161-172
Creep strength and minimum strain rate estimation from Small Punch Creep tests
- 1 July 2018
- Published by Elsevier in Materials Science and Engineering: A
- Vol. 731, 161-172
Open AccessCreep strength and minimum strain rate estimation from Small Punch Creep tests