Kondaiah Gudimetla
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Kondaiah Gudimetla has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
Balasubramanian Ravisankar
National Institute of Technology
4 shared publications- Ramesh Kumar Subramanian
School of Mechanical Engineering, Sastra Deemed to be University, Thanjavur, India
4 shared publications - Balasubramanian Ravisankar
Department of Metallurgical and Materials Engineering, National Institute of Technology, Tiruchirappalli, India
3 shared publications Perumal Venkatachalam
Jayaram College of Engineering and Technology
3 shared publicationsS. Ramesh Kumar
SASTRA Deemed To Be University
2 shared publicationsAnil Babu Sankuru
National Institute of Technology, Tiruchirappalli-620015, Tamil Nadu, India
1 shared publication
Latest Publications
- 12 July 2021
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 74 (11) , 2659-2669
Effect of processing route on microstructure, mechanical and dry sliding wear behavior of commercially pure magnesium processed by ECAP with back pressure
- 12 July 2021
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 74 (11) , 2659-2669
Effect of processing route on microstructure, mechanical and dry sliding wear behavior of commercially pure magnesium processed by ECAP with back pressure
- 30 August 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 969, 361-366
Analysis of the Tribological Properties of Commercial Pure (CP) Aluminum Developed by Chip Consolidation through Equal Channel Angular Pressing (ECAP)
The goal of this research work is to study the role of equal channel angular pressing on consolidation behavior of machined chips of CP Al through ECAP. The chips are collected by orthogonal cutting with cutting edge angle 75° and depth of cut 0.2 mm. The ECAP die with Φ = 90° (channel angle) and Ψ = 20° (corner angle) is used for consolidation of machined chips. The consolidation is done by pre-heating the chips at 200°C upto four passes through processing route BC. The maximum density of 99% and hardness of 94 HV was obtained after 4 ECAP passes. Tribological properties is evaluated by Pin-on-disc dry wear testing for three different loads at a constant sliding speed 750 RPM and distance of 5 kms. Chip consolidated CP Al is inferior in wear resistance with as-received CP Al owed to localised debonding of chips with the sliding disc.
- 30 August 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 969, 361-366
Analysis of the Tribological Properties of Commercial Pure (CP) Aluminum Developed by Chip Consolidation through Equal Channel Angular Pressing (ECAP)
The goal of this research work is to study the role of equal channel angular pressing on consolidation behavior of machined chips of CP Al through ECAP. The chips are collected by orthogonal cutting with cutting edge angle 75° and depth of cut 0.2 mm. The ECAP die with Φ = 90° (channel angle) and Ψ = 20° (corner angle) is used for consolidation of machined chips. The consolidation is done by pre-heating the chips at 200°C upto four passes through processing route BC. The maximum density of 99% and hardness of 94 HV was obtained after 4 ECAP passes. Tribological properties is evaluated by Pin-on-disc dry wear testing for three different loads at a constant sliding speed 750 RPM and distance of 5 kms. Chip consolidated CP Al is inferior in wear resistance with as-received CP Al owed to localised debonding of chips with the sliding disc.
- 30 August 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 969, 565-569
Effect of Back Pressure on the Consolidation Behaviour of Titanium Sponge Particles Processed by ECAP
Titanium is a hard metal with good mechanical properties, corrosion resistant and biocompatibility which makes it have a wide range of applications (biomedical and aerospace). Severe plastic deformation (SPD) is employed to produce Ultrafine Grained (UFG) structures. UFG structures have better mechanical properties due to their compaction. Equal Channel Angular Pressing (ECAP) is adapted to produce a UFG structure in Titanium. In this process, titanium sponge powder is filled in the aluminium shell by intermediate tapping to fill the volume of the shell. The shell is then closed with an Al cap and ECAP is done with continuous back pressure at 300°C. The test specimen has undergone four passes in route BC at different back pressure (50, 100 and 150 MPa) where titanium is consolidated without any crack. Titanium showed decreased grain size and porosity with increasing backpressure. In particular, it is seen that the sample ECAPed by 100 MPa backpressure showed a relative density of about 98% with a hardness of 37 HRC. It is seen that ECAP is more economical and the product obtained by the ECAP process has better properties.
- 30 August 2019
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 969, 565-569
Effect of Back Pressure on the Consolidation Behaviour of Titanium Sponge Particles Processed by ECAP
Titanium is a hard metal with good mechanical properties, corrosion resistant and biocompatibility which makes it have a wide range of applications (biomedical and aerospace). Severe plastic deformation (SPD) is employed to produce Ultrafine Grained (UFG) structures. UFG structures have better mechanical properties due to their compaction. Equal Channel Angular Pressing (ECAP) is adapted to produce a UFG structure in Titanium. In this process, titanium sponge powder is filled in the aluminium shell by intermediate tapping to fill the volume of the shell. The shell is then closed with an Al cap and ECAP is done with continuous back pressure at 300°C. The test specimen has undergone four passes in route BC at different back pressure (50, 100 and 150 MPa) where titanium is consolidated without any crack. Titanium showed decreased grain size and porosity with increasing backpressure. In particular, it is seen that the sample ECAPed by 100 MPa backpressure showed a relative density of about 98% with a hardness of 37 HRC. It is seen that ECAP is more economical and the product obtained by the ECAP process has better properties.
- Open Access
- 1 March 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 330 (1) , 012031
Consolidation of commercial pure aluminum particles by hot ECAP
In the current study undertaken, aluminum particles of commercial purity grade were compacted using hot ECAP. Investigation of the structural evolution and mechanical properties was done. Measurements of the densities of the samples was done for the purpose of evaluation the performance of the consolidation process. A tensile strength (UTS) of 98 MPa (after first pass) was obtained under tensile loads and the percent elongation to fracture was found to be 5.5%, which indicated good tensile strength and ductility as compared to the commercial pure Al powders consolidated by ambient temperature ECAP and other techniques. The relative density and Rockwell hardness (HRB) of compacts (after first pass) was 99% and 42 respectively. This is indisputable proof for establishing the compatibility of ECAP in the matter of producing bulk materials. Characterization of the material microstructure and fracture behavior was done through use of optical and scanning electron microscopy (SEM). The Al powders consolidated at 400°C through ECAP process, exhibited the best combination of yield strength and ductility and hence hot ECAP is suitable method for consolidation of micro powders.
- 1 March 2018
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 330 (1) , 012031
Open AccessConsolidation of commercial pure aluminum particles by hot ECAP
In the current study undertaken, aluminum particles of commercial purity grade were compacted using hot ECAP. Investigation of the structural evolution and mechanical properties was done. Measurements of the densities of the samples was done for the purpose of evaluation the performance of the consolidation process. A tensile strength (UTS) of 98 MPa (after first pass) was obtained under tensile loads and the percent elongation to fracture was found to be 5.5%, which indicated good tensile strength and ductility as compared to the commercial pure Al powders consolidated by ambient temperature ECAP and other techniques. The relative density and Rockwell hardness (HRB) of compacts (after first pass) was 99% and 42 respectively. This is indisputable proof for establishing the compatibility of ECAP in the matter of producing bulk materials. Characterization of the material microstructure and fracture behavior was done through use of optical and scanning electron microscopy (SEM). The Al powders consolidated at 400°C through ECAP process, exhibited the best combination of yield strength and ductility and hence hot ECAP is suitable method for consolidation of micro powders.
- 1 January 2018
- Published by Elsevier in Materials Today: Proceedings
- Vol. 5 (2) , 8241-8248
Microstructure and Mechanical properties of Cu-7wt.% Al Alloy produced by Equal Channel Angular pressing with different routes
- 1 January 2018
- Published by Elsevier in Materials Today: Proceedings
- Vol. 5 (2) , 8241-8248
Microstructure and Mechanical properties of Cu-7wt.% Al Alloy produced by Equal Channel Angular pressing with different routes
- 3 March 2017
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 70 (3) , 639-648
Effect of Microstructure and Mechanical Properties of Al–Mg Alloy Processed by ECAP at Room Temperature and Cryo Temperature
- 3 March 2017
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 70 (3) , 639-648
Effect of Microstructure and Mechanical Properties of Al–Mg Alloy Processed by ECAP at Room Temperature and Cryo Temperature
- 29 March 2016
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 70 (1) , 83-87
Metallurgical and Mechanical Properties of Mild Steel Processed by Equal Channel Angular Pressing (ECAP)
- 29 March 2016
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 70 (1) , 83-87
Metallurgical and Mechanical Properties of Mild Steel Processed by Equal Channel Angular Pressing (ECAP)
- 3 September 2015
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 830-831, 63-66
Effect of Equal Channel Angular Pressing on Densification Behavior of Al 5083 Alloy Powder
In this present study Al-5083 alloy powders were prepared from elemental powders using high energy ball milling under optimized milling parameters. Various properties such as crystalline size, particle size and morphology have been studied using X-Ray diffraction analysis and Scanning Electron Microscopy. It was found that Al-5083 alloy was formed and nanocrystalline size particles were achieved. These nanocrystalline Al-5083 alloy powders were consolidated using equal channel angular pressing with and without application of back pressure. Physical and mechanical properties such as density and hardness are studied.
- 3 September 2015
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 830-831, 63-66
Effect of Equal Channel Angular Pressing on Densification Behavior of Al 5083 Alloy Powder
In this present study Al-5083 alloy powders were prepared from elemental powders using high energy ball milling under optimized milling parameters. Various properties such as crystalline size, particle size and morphology have been studied using X-Ray diffraction analysis and Scanning Electron Microscopy. It was found that Al-5083 alloy was formed and nanocrystalline size particles were achieved. These nanocrystalline Al-5083 alloy powders were consolidated using equal channel angular pressing with and without application of back pressure. Physical and mechanical properties such as density and hardness are studied.
- 2 June 2015
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 68 (S2) , 171-176
Densification of Al 5083 Mechanically Alloyed Powder by Equal Channel Angular Pressing
- 2 June 2015
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 68 (S2) , 171-176
Densification of Al 5083 Mechanically Alloyed Powder by Equal Channel Angular Pressing
- 15 July 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 592-594, 112-116
Densification and Consolidation of Al 5083 Alloy Powder by Equal Channel Angular Pressing
In this present work the elemental powders pertaining to composition of Al5083 alloy was milled using planetary ball mill (Insmart systems) for 20 h. The elemental powders are loaded in HSS vial with 10:1 ball to powder ratio at 250 RPM. Various parameters such as crystalline size, particle size and morphology have studied using X-ray diffraction analysis and scanning electron microscopy. The crystallite size of the powders determined using Williamson Hall analysis of XRD is 23 nm after 20 h of milling. These nanocrystalline Al-5083 alloy powders were consolidated using ECAP with and without application of back pressure. Physical and mechanical properties such as density and hardness values were measured for sintered and unsintered samples.
- 15 July 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 592-594, 112-116
Densification and Consolidation of Al 5083 Alloy Powder by Equal Channel Angular Pressing
In this present work the elemental powders pertaining to composition of Al5083 alloy was milled using planetary ball mill (Insmart systems) for 20 h. The elemental powders are loaded in HSS vial with 10:1 ball to powder ratio at 250 RPM. Various parameters such as crystalline size, particle size and morphology have studied using X-ray diffraction analysis and scanning electron microscopy. The crystallite size of the powders determined using Williamson Hall analysis of XRD is 23 nm after 20 h of milling. These nanocrystalline Al-5083 alloy powders were consolidated using ECAP with and without application of back pressure. Physical and mechanical properties such as density and hardness values were measured for sintered and unsintered samples.