Oncu Akyildiz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Oncu Akyildiz has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
Tarik Omer Ogurtani
Department of Metallurgical and Materials Engineering, Middle East Technical University
7 shared publications- Tarik Omer Ogurtani
Department of Metallurgical and Materials Engineering Middle East Technical University 06531 Ankara Turkey
5 shared publications - Duygu Candemir
Hitit Üniversitesi
4 shared publications - Ersin Emre Oren
Bionanodesign Laboratory, Department of Biomedical Engineering, TOBB University of Economics and Technology, Ankara, Turkey
3 shared publications - Cengiz Bagci
HİTİT ÜNİVERSİTESİ, MÜHENDİSLİK FAKÜLTESİ
2 shared publications - Cengiz Baykasoglu
Hitit Üniversitesi
2 shared publications
Latest Publications
- Open Access
- 20 April 2026
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 29 (4) , 1-7
Aluminum and Zirconium Dual-Doped Nickel-Cobalt-Zinc Oxide Cathode Material for Lithium-Ion Batteries
Aluminum (Al) and zirconium (Zr) doping have been found to enhance the structural and thermal stability, as well as the electrochemical performance of cathode materials, potentially improving their suitability for lithium-ion battery applications. Therefore, in this study, Al and Zr were incorporated into nickel-cobalt-zinc hydroxide material (NiCoZn(OH)2) via sol-gel assisted solid-state doping synthesis to produce dual-doped Li1.05Ni0.8[Co0.054Zn0.046]Al0.08Zr0.02O2 (NCZ-AZ) cathode material. The synthesized powders were characterized using SEM-EDS, XRD, and Rietveld refinement analysis. As a result of the calcination process lasting 20 hours at 800 degrees, the XRD peak intensity ratio I(003)/I(104) was 1.2, and the c/a value was 4.955. These structural parameters are critical to the material's electrochemical stability and charge/discharge cycling performance. Additionally, the cyclic voltammetry test proved the redox reversibility of the cathode material. In conclusion, this study's dual-doped NCZ-AZ cathode material demonstrates promising characteristics for advanced lithium-ion battery applications. A systematic survey of Al and Zr doping in NCZ-AZ can provide valuable information for designing next-generation cathode materials with improved stability and performance.
- 20 April 2026
- Published by Politeknik Dergisi in Journal of Polytechnic
- Vol. 29 (4) , 1-7
Open AccessAluminum and Zirconium Dual-Doped Nickel-Cobalt-Zinc Oxide Cathode Material for Lithium-Ion Batteries
Aluminum (Al) and zirconium (Zr) doping have been found to enhance the structural and thermal stability, as well as the electrochemical performance of cathode materials, potentially improving their suitability for lithium-ion battery applications. Therefore, in this study, Al and Zr were incorporated into nickel-cobalt-zinc hydroxide material (NiCoZn(OH)2) via sol-gel assisted solid-state doping synthesis to produce dual-doped Li1.05Ni0.8[Co0.054Zn0.046]Al0.08Zr0.02O2 (NCZ-AZ) cathode material. The synthesized powders were characterized using SEM-EDS, XRD, and Rietveld refinement analysis. As a result of the calcination process lasting 20 hours at 800 degrees, the XRD peak intensity ratio I(003)/I(104) was 1.2, and the c/a value was 4.955. These structural parameters are critical to the material's electrochemical stability and charge/discharge cycling performance. Additionally, the cyclic voltammetry test proved the redox reversibility of the cathode material. In conclusion, this study's dual-doped NCZ-AZ cathode material demonstrates promising characteristics for advanced lithium-ion battery applications. A systematic survey of Al and Zr doping in NCZ-AZ can provide valuable information for designing next-generation cathode materials with improved stability and performance.
- 17 February 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 672
Stability-performance trade-off in multi-metal layered oxide cathode material derived from Al-Zr modified Ni-Co-Zn-(OH)2 precursor
- 17 February 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 672
Stability-performance trade-off in multi-metal layered oxide cathode material derived from Al-Zr modified Ni-Co-Zn-(OH)2 precursor
- 13 February 2026
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 728
High-performance broadband Nb2O5/n-Si Schottky photodetector for UV–Vis–NIR self-powered applications
- 13 February 2026
- Published by Elsevier in Physica B: Condensed Matter
- Vol. 728
High-performance broadband Nb2O5/n-Si Schottky photodetector for UV–Vis–NIR self-powered applications
- 28 January 2026
- Published by Wiley in Energy Storage
- Vol. 8 (1)
Electrochemical Performance of Al/Nb 2 O 5 // GO / Cu Asymmetric Hybrid Supercapacitors With Aqueous Potassium Hydroxide Electrolytes at Varying Concentrations
Asymmetric hybrid supercapacitors integrating transition metal oxides with carbonaceous electrodes have attracted significant attention for advanced energy storage applications due to their ability to combine high energy density with rapid power delivery. In this study, an Al/Nb 2 O 5 cathode and a Cu/graphene oxide (GO) anode were fabricated via slurry casting and electrophoretic deposition (EPD), respectively, and assembled with a paper separator in aqueous potassium hydroxide (KOH) electrolytes of varying concentrations (1, 2, and 3 M). Structural and morphological analyses confirmed the orthorhombic phase of Nb 2 O 5 and the uniform deposition of GO films. Galvanostatic charge–discharge (GCD) and electrochemical impedance spectroscopy (EIS) measurements revealed a strong dependence of electrochemical performance on electrolyte concentration. The device operating in 2 M KOH exhibited the most favorable balance between energy and power densities, achieving a specific capacitance of 30.7 F g −1 , energy density of 36.5 Wh kg −1 , and power density of 295 W kg −1 , with a relaxation time constant of 0.634 ms. In contrast, 1 M KOH provided moderate energy storage capability, while 3 M KOH suffered from reduced capacitance due to increased viscosity and ion–ion interactions. Comparative analysis with literature data highlights the competitive performance of the Al/Nb 2 O 5 //Cu/GO configuration, particularly in terms of energy–power trade‐off. These findings underscore the critical role of electrolyte optimization and electrode design in advancing hybrid supercapacitors for sustainable energy storage applications.
- 28 January 2026
- Published by Wiley in Energy Storage
- Vol. 8 (1)
Electrochemical Performance of Al/Nb 2 O 5 // GO / Cu Asymmetric Hybrid Supercapacitors With Aqueous Potassium Hydroxide Electrolytes at Varying Concentrations
Asymmetric hybrid supercapacitors integrating transition metal oxides with carbonaceous electrodes have attracted significant attention for advanced energy storage applications due to their ability to combine high energy density with rapid power delivery. In this study, an Al/Nb 2 O 5 cathode and a Cu/graphene oxide (GO) anode were fabricated via slurry casting and electrophoretic deposition (EPD), respectively, and assembled with a paper separator in aqueous potassium hydroxide (KOH) electrolytes of varying concentrations (1, 2, and 3 M). Structural and morphological analyses confirmed the orthorhombic phase of Nb 2 O 5 and the uniform deposition of GO films. Galvanostatic charge–discharge (GCD) and electrochemical impedance spectroscopy (EIS) measurements revealed a strong dependence of electrochemical performance on electrolyte concentration. The device operating in 2 M KOH exhibited the most favorable balance between energy and power densities, achieving a specific capacitance of 30.7 F g −1 , energy density of 36.5 Wh kg −1 , and power density of 295 W kg −1 , with a relaxation time constant of 0.634 ms. In contrast, 1 M KOH provided moderate energy storage capability, while 3 M KOH suffered from reduced capacitance due to increased viscosity and ion–ion interactions. Comparative analysis with literature data highlights the competitive performance of the Al/Nb 2 O 5 //Cu/GO configuration, particularly in terms of energy–power trade‐off. These findings underscore the critical role of electrolyte optimization and electrode design in advancing hybrid supercapacitors for sustainable energy storage applications.
- 27 September 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (14) , 14846-14859
Simulation of the Kinetics of Microstructure Evolution during Destabilization and Tempering of a High-Chromium White Cast Iron
- 27 September 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (14) , 14846-14859
Simulation of the Kinetics of Microstructure Evolution during Destabilization and Tempering of a High-Chromium White Cast Iron
- 1 February 2023
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 28 (2) , 118-127
A fully coupled thermal–microstructural–mechanical finite element process model for directed energy deposition additive manufacturing of Ti–6Al–4V
A fully coupled thermal–microstructural–mechanical finite element modelling framework is developed to investigate the distortion and residual stresses during directed energy deposition (DED) of multi-phase Ti–6Al–4V alloy. The Johnson–Cook constitutive model is used to predict the yield strength of each phase as a function of strain, strain rate and temperature where the flow stress is calculated by a linear mixing rule based on the volumetric phase fractions. A thin-walled rectangular sample is chosen as the reference geometry and the results are compared with experimentally measured in situ thermal history and distortion data, where a reasonable agreement is achieved. The proposed modelling framework with physics-based material constitutive model provides useful information for a better understanding of process–microstructure–property relations in additive manufacturing by DED.
- 1 February 2023
- Published by SAGE Publications in Science and Technology of Welding and Joining
- Vol. 28 (2) , 118-127
A fully coupled thermal–microstructural–mechanical finite element process model for directed energy deposition additive manufacturing of Ti–6Al–4V
A fully coupled thermal–microstructural–mechanical finite element modelling framework is developed to investigate the distortion and residual stresses during directed energy deposition (DED) of multi-phase Ti–6Al–4V alloy. The Johnson–Cook constitutive model is used to predict the yield strength of each phase as a function of strain, strain rate and temperature where the flow stress is calculated by a linear mixing rule based on the volumetric phase fractions. A thin-walled rectangular sample is chosen as the reference geometry and the results are compared with experimentally measured in situ thermal history and distortion data, where a reasonable agreement is achieved. The proposed modelling framework with physics-based material constitutive model provides useful information for a better understanding of process–microstructure–property relations in additive manufacturing by DED.
- Open Access
- 31 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (2) , 026411
Influence of displacement constraints to the surface reconstruction of stressed bicrystal thin films
In this work, surface morphology evolution of bicrystal thin films under the combined action of grain boundary and surface diffusion is investigated by considering different mechanical constraints. 2D surface topographies of thin films, that are (a) freestanding, (b) strongly bonded to its substrate and (c) strongly bonded to its substrate and one of sidewalls, are simulated using a numerical implementation of an irreversible thermo-kinetics model. Relationships which give the groove depth as a function of time are obtained. Results show that mechanical loading conditions are effective in determining the morphology and kinetics of grooving. For the three scenarios that had been investigated, it was found that the groove depth evolves linearly with different tip velocities under the same level of uniaxial tension. In freestanding films groove tip evolves faster; i.e. as the film gets constrained from its substrate and/or one of its sidewalls, the tip velocity slows down. It was also observed that high triple junction mobilities at low levels of applied stress hinder the effects of displacement constraints to groove shape, even in the case of asymmetric stress distributions inside the film. On the other hand, low triple junction mobilities at moderate applied stresses allow formation of asymmetric grain boundary grooves due to the induced asymmetry in the driving force for surface diffusion with respect to the grain boundary.
- 31 January 2020
- Published by IOP Publishing in Materials Research Express
- Vol. 7 (2) , 026411
Open AccessInfluence of displacement constraints to the surface reconstruction of stressed bicrystal thin films
In this work, surface morphology evolution of bicrystal thin films under the combined action of grain boundary and surface diffusion is investigated by considering different mechanical constraints. 2D surface topographies of thin films, that are (a) freestanding, (b) strongly bonded to its substrate and (c) strongly bonded to its substrate and one of sidewalls, are simulated using a numerical implementation of an irreversible thermo-kinetics model. Relationships which give the groove depth as a function of time are obtained. Results show that mechanical loading conditions are effective in determining the morphology and kinetics of grooving. For the three scenarios that had been investigated, it was found that the groove depth evolves linearly with different tip velocities under the same level of uniaxial tension. In freestanding films groove tip evolves faster; i.e. as the film gets constrained from its substrate and/or one of its sidewalls, the tip velocity slows down. It was also observed that high triple junction mobilities at low levels of applied stress hinder the effects of displacement constraints to groove shape, even in the case of asymmetric stress distributions inside the film. On the other hand, low triple junction mobilities at moderate applied stresses allow formation of asymmetric grain boundary grooves due to the induced asymmetry in the driving force for surface diffusion with respect to the grain boundary.
- Open Access
- 30 June 2019
- Published by Mugla Sitki Kocman University in Mugla Journal of Science and Technology
- Vol. 5 (1) , 137-142
ASSESSING THE VOLUME FRACTIONS OF THE PHASES, NODULARITY AND NODULE COUNT OF SPHEROIDAL GRAPHITE CAST IRON USING IMAGEJ SOFTWARE
In this study, a simple method for assessing the microstructure of ductile cast iron by using a freeware digital image processing software is described. The method is applied to three different ductile iron grades to assess their ferrite, pearlite and graphite volume fractions as well as graphite nodularity, nodule count, nodule size. All specimens were found to show good nodularity (~ 88 % by area) with different graphite average size and perimeter morphology. The amount of graphite was also found to be similar (11±2 % by area) in all specimens. On the other hand, ferrite percentages were found as 85.8, 57.1, and 52.5 % respectively for ASTM A536 grades 60-40-18, 65-45-12, and 80-55-06. It was also found that among these three grades, the higher the pearlite content, the higher the hardness. The agreement with the standards confirms that quantitative metallography through image processing is a powerful tool in order to estimate the mechanical properties of cast irons.
- 30 June 2019
- Published by Mugla Sitki Kocman University in Mugla Journal of Science and Technology
- Vol. 5 (1) , 137-142
Open AccessASSESSING THE VOLUME FRACTIONS OF THE PHASES, NODULARITY AND NODULE COUNT OF SPHEROIDAL GRAPHITE CAST IRON USING IMAGEJ SOFTWARE
In this study, a simple method for assessing the microstructure of ductile cast iron by using a freeware digital image processing software is described. The method is applied to three different ductile iron grades to assess their ferrite, pearlite and graphite volume fractions as well as graphite nodularity, nodule count, nodule size. All specimens were found to show good nodularity (~ 88 % by area) with different graphite average size and perimeter morphology. The amount of graphite was also found to be similar (11±2 % by area) in all specimens. On the other hand, ferrite percentages were found as 85.8, 57.1, and 52.5 % respectively for ASTM A536 grades 60-40-18, 65-45-12, and 80-55-06. It was also found that among these three grades, the higher the pearlite content, the higher the hardness. The agreement with the standards confirms that quantitative metallography through image processing is a powerful tool in order to estimate the mechanical properties of cast irons.
- Open Access
- 31 December 2018
- Published by Uludag University Journal of the Faculty of Engineering in Uludağ University Journal of The Faculty of Engineering
- Vol. 23 (3) , 179-190
YÜKSEK KROMLU BEYAZ DÖKME DEMİRLERDE FAZ DENGESİNİN BENZETİMİ
In this study, using the Materials Calculator software program, the pseudo binary phase diagrams (i.e. isoplethal maps) of high chromium white cast irons (~19% in weight) with different molybdenum contents were simulated. In order to test the accuracy of the calculated phase diagrams, the transformation temperatures read from the diagrams at certain compositions were compared with the phase transformation temperatures measured using Differential Scanning Calorimetry (DSC) analysis of the samples produced by casting in the same composition followed by slow cooling. With the same purpose, low temperature phases read from the phase diagrams were compared with the crystalline phases determined by X-Ray Diffraction (XRD) of the casted samples. Simulated diagrams predicted an increase in the amount of secondary M 23 C 6 carbides with increasing molybdenum content. The validity of this prediction was tested by determining the phase distribution and phase compositions in the casted samples by means of metallographic examinations and Scanning Electron Microscopy (SEM) - Energy Dispersive Spectroscopy (EDS) analyzes. When the hardness values of the samples were taken into consideration, it was seen that the hardness increased from 44.90 to 51.05 HRC with a 1% increase in Mo content and a corresponding increase in the amount of secondary carbides without any heat treatments. Results show that theoretical predictions and experimental measurements are in accord and estimating phase equilibria in multi-component systems is of practical importance.
- 31 December 2018
- Published by Uludag University Journal of the Faculty of Engineering in Uludağ University Journal of The Faculty of Engineering
- Vol. 23 (3) , 179-190
Open AccessYÜKSEK KROMLU BEYAZ DÖKME DEMİRLERDE FAZ DENGESİNİN BENZETİMİ
In this study, using the Materials Calculator software program, the pseudo binary phase diagrams (i.e. isoplethal maps) of high chromium white cast irons (~19% in weight) with different molybdenum contents were simulated. In order to test the accuracy of the calculated phase diagrams, the transformation temperatures read from the diagrams at certain compositions were compared with the phase transformation temperatures measured using Differential Scanning Calorimetry (DSC) analysis of the samples produced by casting in the same composition followed by slow cooling. With the same purpose, low temperature phases read from the phase diagrams were compared with the crystalline phases determined by X-Ray Diffraction (XRD) of the casted samples. Simulated diagrams predicted an increase in the amount of secondary M 23 C 6 carbides with increasing molybdenum content. The validity of this prediction was tested by determining the phase distribution and phase compositions in the casted samples by means of metallographic examinations and Scanning Electron Microscopy (SEM) - Energy Dispersive Spectroscopy (EDS) analyzes. When the hardness values of the samples were taken into consideration, it was seen that the hardness increased from 44.90 to 51.05 HRC with a 1% increase in Mo content and a corresponding increase in the amount of secondary carbides without any heat treatments. Results show that theoretical predictions and experimental measurements are in accord and estimating phase equilibria in multi-component systems is of practical importance.
- 23 February 2018
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 140 (5)
Predicting Microstructure Evolution During Directed Energy Deposition Additive Manufacturing of Ti-6Al-4V
Laser engineering net shaping (LENS) is one of the representative processes of directed energy deposition (DED) in which a moving heat source having high-intensity melts and fuses metal powders together to print parts. The complex and nonuniform thermal gradients during the laser heating and cooling cycles in the LENS process directly affect the microstructural characteristics, and thereby the ultimate mechanical properties of fabricated parts. Therefore, prediction of microstructure evolution during the LENS process is of paramount importance. The objective of this study is to present a thermo-microstructural model for predicting microstructure evolution during the LENS process of Ti-6Al-4V. First, a detailed transient thermal finite element (FE) model is developed and validated for a sample LENS process. Then, a density type microstructural model which enables calculation of the α-phase fractions (i.e., Widmanstätten colony and basketweave α-phase fractions), β-phase fraction, and alpha lath widths during LENS process is developed and coupled to the thermal model. The microstructural algorithm is first verified by comparing the phase fraction results with the results presented in the literature for a given thermal history data. Second, the average lath width values calculated using the model are compared with the experimentally measured counterparts, where a reasonable agreement is achieved in both cases.
- 23 February 2018
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 140 (5)
Predicting Microstructure Evolution During Directed Energy Deposition Additive Manufacturing of Ti-6Al-4V
Laser engineering net shaping (LENS) is one of the representative processes of directed energy deposition (DED) in which a moving heat source having high-intensity melts and fuses metal powders together to print parts. The complex and nonuniform thermal gradients during the laser heating and cooling cycles in the LENS process directly affect the microstructural characteristics, and thereby the ultimate mechanical properties of fabricated parts. Therefore, prediction of microstructure evolution during the LENS process is of paramount importance. The objective of this study is to present a thermo-microstructural model for predicting microstructure evolution during the LENS process of Ti-6Al-4V. First, a detailed transient thermal finite element (FE) model is developed and validated for a sample LENS process. Then, a density type microstructural model which enables calculation of the α-phase fractions (i.e., Widmanstätten colony and basketweave α-phase fractions), β-phase fraction, and alpha lath widths during LENS process is developed and coupled to the thermal model. The microstructural algorithm is first verified by comparing the phase fraction results with the results presented in the literature for a given thermal history data. Second, the average lath width values calculated using the model are compared with the experimentally measured counterparts, where a reasonable agreement is achieved in both cases.