Li Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Li Wang has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
- Sima Dimitrijev
Griffith University
21 shared publications Philip Tanner
Queensland Micro- and Nanotechnology Centre, Griffith University, Queensland, Australia
12 shared publicationsAlan Iacopi
Queensland Micro- and Nanotechnology Centre, Griffith University, Nathan, Australia
10 shared publications- Dzung Viet Dao
Griffith University
9 shared publications - Hoang-Phuong Phan
School of Mechanical and Manufacturing Engineering The University of New South Wales Sydney New South Wales Australia
9 shared publications Jisheng Han
Queensland Micro- and Nanotechnology Centre, Griffith University, Queensland, Australia
8 shared publications
Latest Publications
- 9 February 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (20) , 16662-16667
Growth mechanism for alternating supply epitaxy: the unique pathway to achieve uniform silicon carbide films on multiple large-diameter silicon substrates
The unique growth mechanism of alternating supply epitaxy enables uniform 3C-SiC to be deposited on multiple large-diameter Si wafers.
- 9 February 2016
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 6 (20) , 16662-16667
Growth mechanism for alternating supply epitaxy: the unique pathway to achieve uniform silicon carbide films on multiple large-diameter silicon substrates
The unique growth mechanism of alternating supply epitaxy enables uniform 3C-SiC to be deposited on multiple large-diameter Si wafers.
- Open Access
- 25 November 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 17026
Vertically Conductive Single-Crystal SiC-Based Bragg Reflector Grown on Si Wafer
Single-crystal silicon carbide (SiC) thin-films on silicon (Si) were used for the fabrication and characterization of electrically conductive distributed Bragg reflectors (DBRs) on 100 mm Si wafers. The DBRs, each composed of 3 alternating layers of SiC and Al(Ga)N grown on Si substrates, show high wafer uniformity with a typical maximum reflectance of 54% in the blue spectrum and a stopband (at 80% maximum reflectance) as large as 100 nm. Furthermore, high vertical electrical conduction is also demonstrated resulting to a density of current exceeding 70 A/cm2 above 1.5 V. Such SiC/III-N DBRs with high thermal and electrical conductivities could be used as pseudo-substrate to enhance the efficiency of SiC-based and GaN-based optoelectronic devices on large Si wafers.
- 25 November 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 17026
Open AccessVertically Conductive Single-Crystal SiC-Based Bragg Reflector Grown on Si Wafer
Single-crystal silicon carbide (SiC) thin-films on silicon (Si) were used for the fabrication and characterization of electrically conductive distributed Bragg reflectors (DBRs) on 100 mm Si wafers. The DBRs, each composed of 3 alternating layers of SiC and Al(Ga)N grown on Si substrates, show high wafer uniformity with a typical maximum reflectance of 54% in the blue spectrum and a stopband (at 80% maximum reflectance) as large as 100 nm. Furthermore, high vertical electrical conduction is also demonstrated resulting to a density of current exceeding 70 A/cm2 above 1.5 V. Such SiC/III-N DBRs with high thermal and electrical conductivities could be used as pseudo-substrate to enhance the efficiency of SiC-based and GaN-based optoelectronic devices on large Si wafers.
- Open Access
- 21 October 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 15423
Kinetic surface roughening and wafer bow control in heteroepitaxial growth of 3C-SiC on Si(111) substrates
A thin, chemically inert 3C-SiC layer between GaN and Si helps not only to avoid the “melt-back” effect, but also to inhibit the crack generation in the grown GaN layers. The quality of GaN layer is heavily dependent on the unique properties of the available 3C-SiC/Si templates. In this paper, the parameters influencing the roughness, crystalline quality and wafer bow are investigated and engineered to obtain high quality, low roughness 3C-SiC/Si templates suitable for subsequent GaN growth and device processing. Kinetic surface roughening and SiC growth mechanisms, which depend on both deposition temperature and off-cut angle, are reported for heteroepitaxial growth of 3C-SiC on Si substrates. The narrower terrace width on 4° off-axis Si enhances the step-flow growth at 1200 °C, with the roughness of 3C-SiC remaining constant with increasing thickness, corresponding to a scaling exponent of zero. Crack-free 3C-SiC grown on 150-mm Si substrate with a wafer bow of less than 20 μm was achieved. Both concave and convex wafer bow can be obtained by in situ tuning of the deposited SiC layer thicknesses. The 3C-SiC grown on off-axis Si, compared to that grown on on-axis Si, has lower surface roughness, better crystallinity and smaller bow magnitude.
- 21 October 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 15423
Open AccessKinetic surface roughening and wafer bow control in heteroepitaxial growth of 3C-SiC on Si(111) substrates
A thin, chemically inert 3C-SiC layer between GaN and Si helps not only to avoid the “melt-back” effect, but also to inhibit the crack generation in the grown GaN layers. The quality of GaN layer is heavily dependent on the unique properties of the available 3C-SiC/Si templates. In this paper, the parameters influencing the roughness, crystalline quality and wafer bow are investigated and engineered to obtain high quality, low roughness 3C-SiC/Si templates suitable for subsequent GaN growth and device processing. Kinetic surface roughening and SiC growth mechanisms, which depend on both deposition temperature and off-cut angle, are reported for heteroepitaxial growth of 3C-SiC on Si substrates. The narrower terrace width on 4° off-axis Si enhances the step-flow growth at 1200 °C, with the roughness of 3C-SiC remaining constant with increasing thickness, corresponding to a scaling exponent of zero. Crack-free 3C-SiC grown on 150-mm Si substrate with a wafer bow of less than 20 μm was achieved. Both concave and convex wafer bow can be obtained by in situ tuning of the deposited SiC layer thicknesses. The 3C-SiC grown on off-axis Si, compared to that grown on on-axis Si, has lower surface roughness, better crystallinity and smaller bow magnitude.
- Open Access
- 2 September 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 3 (37) , 9748
Correction: The effect of device geometry and crystal orientation on the stress-dependent offset voltage of 3C–SiC(100) four terminal devices
Correction for ‘The effect of device geometry and crystal orientation on the stress-dependent offset voltage of 3C–SiC(100) four terminal devices’ by Afzaal Qamar et al., J. Mater. Chem. C, 2015, 3, 8804–8809.
- 2 September 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 3 (37) , 9748
Open AccessCorrection: The effect of device geometry and crystal orientation on the stress-dependent offset voltage of 3C–SiC(100) four terminal devices
Correction for ‘The effect of device geometry and crystal orientation on the stress-dependent offset voltage of 3C–SiC(100) four terminal devices’ by Afzaal Qamar et al., J. Mater. Chem. C, 2015, 3, 8804–8809.
- 31 July 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 3 (34) , 8804-8809
The effect of device geometry and crystal orientation on the stress-dependent offset voltage of 3C–SiC(100) four terminal devices
This communication reports for the first time, the impact of device geometry on the stress-dependent offset voltage of single crystal p-type 3C–SiC four terminal devices. Single crystal p-type 3C–SiC(100) was grown by low pressure chemical vapor deposition and three different device geometries (cross, rectangle and square) were fabricated using the conventional photolithography and dry etching processes. It was observed that the stress-dependent offset voltage of the devices strongly depends upon the device geometry and it can be increased by almost 100% by just selecting the appropriate device geometry. We also found that as the device is rotated within the (100) crystal plane its stress sensitivity varies from ≈0 to 9 × 10−11 Pa−1.
- 31 July 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 3 (34) , 8804-8809
The effect of device geometry and crystal orientation on the stress-dependent offset voltage of 3C–SiC(100) four terminal devices
This communication reports for the first time, the impact of device geometry on the stress-dependent offset voltage of single crystal p-type 3C–SiC four terminal devices. Single crystal p-type 3C–SiC(100) was grown by low pressure chemical vapor deposition and three different device geometries (cross, rectangle and square) were fabricated using the conventional photolithography and dry etching processes. It was observed that the stress-dependent offset voltage of the devices strongly depends upon the device geometry and it can be increased by almost 100% by just selecting the appropriate device geometry. We also found that as the device is rotated within the (100) crystal plane its stress sensitivity varies from ≈0 to 9 × 10−11 Pa−1.
- 30 June 2015
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 821-823, 205-208
Si Surface Preparation for Heteroepitaxial Growth of SiC Using In Situ Oxidation
To achieve high quality SiC growth on Si substrate, it is essential to get a smooth Si surface without forming SiC and graphitic islands during the surface cleaning and before the carbonisation process. In this paper, a novel in-situ surface cleaning method designed for the hetero-epitaxial growth of SiC on Si substrate is developed using a custom-made low-pressure chemical vapour deposition reactor. The results indicate that the combination of ramping in oxygen and subsequent flowing of SiH4 avoids the contamination of Si, enables the oxide layer to be removed smoothly, and subsequently creates a smooth Si surface with regular atomic steps. SiC grown on off-axis Si has better crystallinity and significantly smaller roughness than that grown on on-axis Si.
- 30 June 2015
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 821-823, 205-208
Si Surface Preparation for Heteroepitaxial Growth of SiC Using In Situ Oxidation
To achieve high quality SiC growth on Si substrate, it is essential to get a smooth Si surface without forming SiC and graphitic islands during the surface cleaning and before the carbonisation process. In this paper, a novel in-situ surface cleaning method designed for the hetero-epitaxial growth of SiC on Si substrate is developed using a custom-made low-pressure chemical vapour deposition reactor. The results indicate that the combination of ramping in oxygen and subsequent flowing of SiH4 avoids the contamination of Si, enables the oxide layer to be removed smoothly, and subsequently creates a smooth Si surface with regular atomic steps. SiC grown on off-axis Si has better crystallinity and significantly smaller roughness than that grown on on-axis Si.
- 22 June 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (69) , 56377-56381
Orientation dependence of the pseudo-Hall effect in p-type 3C–SiC four-terminal devices under mechanical stress
This paper presents for the first time the orientation dependence of the pseudo-Hall effect in p-type 3C–SiC four-terminal devices under mechanical stress. Experimental results indicate that the offset voltage of p-type 3C–SiC four-terminal devices significantly depends on the directions of the applied current and stress. We also calculated the piezoresistive coefficients π61, π62, and π66, showing that π66 with its maximum value of approximately 16.7 × 10−11 Pa−1 plays a more dominant role than π61 and π62. The magnitude of the offset voltage in arbitrary orientation under stress was estimated based on these coefficients. The finding in this study plays an important role in the optimization of Microelectromechanical Systems (MEMS) mechanical sensors utilizing the pseudo-Hall effect in p-type 3C–SiC.
- 22 June 2015
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 5 (69) , 56377-56381
Orientation dependence of the pseudo-Hall effect in p-type 3C–SiC four-terminal devices under mechanical stress
This paper presents for the first time the orientation dependence of the pseudo-Hall effect in p-type 3C–SiC four-terminal devices under mechanical stress. Experimental results indicate that the offset voltage of p-type 3C–SiC four-terminal devices significantly depends on the directions of the applied current and stress. We also calculated the piezoresistive coefficients π61, π62, and π66, showing that π66 with its maximum value of approximately 16.7 × 10−11 Pa−1 plays a more dominant role than π61 and π62. The magnitude of the offset voltage in arbitrary orientation under stress was estimated based on these coefficients. The finding in this study plays an important role in the optimization of Microelectromechanical Systems (MEMS) mechanical sensors utilizing the pseudo-Hall effect in p-type 3C–SiC.
- 26 May 2015
- Published by IOP Publishing in Applied Physics Express
- Vol. 8 (6)
Charge transport and activation energy of amorphous silicon carbide thin film on quartz at elevated temperature
- 26 May 2015
- Published by IOP Publishing in Applied Physics Express
- Vol. 8 (6)
Charge transport and activation energy of amorphous silicon carbide thin film on quartz at elevated temperature
- 20 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 36 (7) , 708-710
The Dependence of Offset Voltage in p-Type 3C-SiC van der Pauw Device on Applied Strain
This letter reports for the first time the strain dependence of the offset voltage in p-type 3C-SiC van der Pauw square device. The p-type 3C-SiC thin film was epitaxially grown on a p-type Si(100) wafer using low pressure chemical vapor deposition followed by a conventional photolithography and dry etch processes, forming four-terminal van der Pauw device. The influence of applied tensile and compressive strain on the offset voltage of the van der Pauw device was investigated using the bending beam method. Experimental results showed that the offset voltage of the device is significantly changed by applied compressive and tensile strain, indicating the feasibility of using this effect for mechanical sensing applications. The sensitivity of the device to the applied strain has been found to be 70 (mV/A)/ppm.
- 20 May 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 36 (7) , 708-710
The Dependence of Offset Voltage in p-Type 3C-SiC van der Pauw Device on Applied Strain
This letter reports for the first time the strain dependence of the offset voltage in p-type 3C-SiC van der Pauw square device. The p-type 3C-SiC thin film was epitaxially grown on a p-type Si(100) wafer using low pressure chemical vapor deposition followed by a conventional photolithography and dry etch processes, forming four-terminal van der Pauw device. The influence of applied tensile and compressive strain on the offset voltage of the van der Pauw device was investigated using the bending beam method. Experimental results showed that the offset voltage of the device is significantly changed by applied compressive and tensile strain, indicating the feasibility of using this effect for mechanical sensing applications. The sensitivity of the device to the applied strain has been found to be 70 (mV/A)/ppm.
- 8 January 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 3 (6) , 1172-1176
The effect of strain on the electrical conductance of p-type nanocrystalline silicon carbide thin films
A significant piezoresistive effect in p-type nanocrystalline SiC with a gauge factor of 14.5 was reported. This result indicates that p-type nanocrystalline SiC is a good candidate for MEMS sensors used in harsh environments and bio applications.
- 8 January 2015
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 3 (6) , 1172-1176
The effect of strain on the electrical conductance of p-type nanocrystalline silicon carbide thin films
A significant piezoresistive effect in p-type nanocrystalline SiC with a gauge factor of 14.5 was reported. This result indicates that p-type nanocrystalline SiC is a good candidate for MEMS sensors used in harsh environments and bio applications.