Peter Ragaert
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Peter Ragaert has a total of 89 co-authors. Here are the top co-authors by number of shared publications:
Frank Devlieghere
Ghent University (UGent)
9 shared publicationsAn Vermeulen
Pack4Food Ghent Belgium
5 shared publicationsBruno De Meulenaer
Research Group Food Chemistry and Human Nutrition (nutriFOODchem), Department of Food Technology, Safety and Health Ghent University Ghent Belgium
5 shared publications- Frank Devlieghere
Research Unit Food Microbiology and Food Preservation (FMFP), Department of Food Technology, Safety and Health, Faculty of Bioscience Engineering, Ghent University, Coupure Links 653, B-9000 Ghent, Belgium
4 shared publications Dimitri Adons
IMO‐IMOMEC, Packaging Technology Centre Hasselt University Diepenbeek Belgium
3 shared publications- Kim Ragaert
Maastricht University
3 shared publications
Latest Publications
- Open Access
- 27 January 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 228
Modelling material flows and cost-benefit of sorting PLA packaging waste in material recovery facilities under different market penetration scenarios
- 27 January 2026
- Published by Elsevier in Resources, Conservation and Recycling
- Vol. 228
Open AccessModelling material flows and cost-benefit of sorting PLA packaging waste in material recovery facilities under different market penetration scenarios
- Open Access
- 22 November 2025
- Published by Elsevier in Environmental Science and Ecotechnology
- Vol. 28
Microbial protein-derived bioplastics from renewable substrates: pathways, challenges, and applications in a circular economy
- 22 November 2025
- Published by Elsevier in Environmental Science and Ecotechnology
- Vol. 28
Open AccessMicrobial protein-derived bioplastics from renewable substrates: pathways, challenges, and applications in a circular economy
- Open Access
Impact of Multiple Reprocessing on Properties of Polyhydroxybutyrate and Polypropylene
Biobased plastics have the potential to be sustainable, but to explore their circularity further, current end-of-life options need to be broadened. Mechanical recycling is one of the most accepted methods to bring back plastics into the loop. Polyhydroxybutyrates (PHBs) are biobased and biodegradable in nature with promising properties and varied applications in the market. This study focuses on their potential for mechanical recycling by multiple extrusion cycles (E1–E5) and multi-faceted characterization of the virgin (V) and reprocessed materials from E1 to E5. The behavior is compared to polypropylene (PP) as a reference with a similar property profile, which has also been reprocessed five times. The thermal properties of both series showed a stable melting point and thermal decomposition temperature from thermal analyses (differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA)). However, a steady increase in the degree of crystallinity was observed which could counterbalance the decrease in molecular weight due to repeated extrusion measured by gel permeation chromatography and resulted in similar values of tensile strength across the cycles. The strain at break was impacted after the first extrusion, but no significant change was observed thereafter; the same was observed for impact strength. Even in scanning electron microscopy (SEM) images, virgin and E5 samples appeared similar, showing the stability of morphological characteristics. Fourier transform infrared spectroscopy (FTIR) results revealed that no new groups are being formed even on repeated processing. The deviation between the PHB and PP series was more predominant in the melt mass flow rate (MFR) and rheology studies. There was a drastic drop in the MFR values in PHB from virgin to E5, whereas not much difference was observed for PP throughout the cycles. This observation was corroborated by frequency sweeps conducted with the parallel plate method. The viscosity dropped from virgin to E1 and E2, but from E3 to E5 it presented similar values. This was in contrast to PP, where all the samples from virgin to E5 had the same values of viscosity. This paper highlights the possibilities of mechanical recycling of PHB and explains why future work with the addition of virgin material and other additives is an area to be explored.
Open AccessImpact of Multiple Reprocessing on Properties of Polyhydroxybutyrate and Polypropylene
Biobased plastics have the potential to be sustainable, but to explore their circularity further, current end-of-life options need to be broadened. Mechanical recycling is one of the most accepted methods to bring back plastics into the loop. Polyhydroxybutyrates (PHBs) are biobased and biodegradable in nature with promising properties and varied applications in the market. This study focuses on their potential for mechanical recycling by multiple extrusion cycles (E1–E5) and multi-faceted characterization of the virgin (V) and reprocessed materials from E1 to E5. The behavior is compared to polypropylene (PP) as a reference with a similar property profile, which has also been reprocessed five times. The thermal properties of both series showed a stable melting point and thermal decomposition temperature from thermal analyses (differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA)). However, a steady increase in the degree of crystallinity was observed which could counterbalance the decrease in molecular weight due to repeated extrusion measured by gel permeation chromatography and resulted in similar values of tensile strength across the cycles. The strain at break was impacted after the first extrusion, but no significant change was observed thereafter; the same was observed for impact strength. Even in scanning electron microscopy (SEM) images, virgin and E5 samples appeared similar, showing the stability of morphological characteristics. Fourier transform infrared spectroscopy (FTIR) results revealed that no new groups are being formed even on repeated processing. The deviation between the PHB and PP series was more predominant in the melt mass flow rate (MFR) and rheology studies. There was a drastic drop in the MFR values in PHB from virgin to E5, whereas not much difference was observed for PP throughout the cycles. This observation was corroborated by frequency sweeps conducted with the parallel plate method. The viscosity dropped from virgin to E1 and E2, but from E3 to E5 it presented similar values. This was in contrast to PP, where all the samples from virgin to E5 had the same values of viscosity. This paper highlights the possibilities of mechanical recycling of PHB and explains why future work with the addition of virgin material and other additives is an area to be explored.
- Open Access
- 16 October 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (20) , 2774
Degradable Plasma-Polymerized Poly(Ethylene Glycol)-Like Coating as a Matrix for Food-Packaging Applications
Currently, there is considerable interest in seeking an environmentally friendly technique that is neither thermally nor organic solvent-dependent for producing advanced polymer films for food-packaging applications. Among different approaches, plasma polymerization is a promising method that can deposit biodegradable coatings on top of polymer films. In this study, an atmospheric-pressure aerosol-assisted plasma deposition method was employed to develop a poly(ethylene glycol) (PEG)-like coating, which can act as a potential matrix for antimicrobial agents, by envisioning controlled-release food-packaging applications. Different plasma operating parameters, including the input power, monomer flow rate, and gap between the edge of the plasma head and substrate, were optimized to produce a PEG-like coating with a desirable water stability level and that can be biodegradable. The findings revealed that increased distance between the plasma head and substrate intensified gas-phase nucleation and diluted the active plasma species, which in turn led to the formation of a non-conformal rough coating. Conversely, at short plasma–substrate distances, smooth conformal coatings were obtained. Furthermore, at low input powers (<250 W), the chemical structure of the precursor was mostly preserved with a high retention of C-O functional groups due to limited monomer fragmentation. At the same time, these coatings exhibit low stability in water, which could be attributed to their low cross-linking degree. Increasing the power to 350 W resulted in the loss of the PEG-like chemical structure, which is due to the enhanced monomer fragmentation at high power. Nevertheless, owing to the enhanced cross-linking degree, these coatings were more stable in water. Finally, it could be concluded that a moderate input power (250–300 W) should be applied to obtain an acceptable tradeoff between the coating stability and PEG resemblance.
- 16 October 2023
- Published by MDPI AG in Nanomaterials
- Vol. 13 (20) , 2774
Open AccessDegradable Plasma-Polymerized Poly(Ethylene Glycol)-Like Coating as a Matrix for Food-Packaging Applications
Currently, there is considerable interest in seeking an environmentally friendly technique that is neither thermally nor organic solvent-dependent for producing advanced polymer films for food-packaging applications. Among different approaches, plasma polymerization is a promising method that can deposit biodegradable coatings on top of polymer films. In this study, an atmospheric-pressure aerosol-assisted plasma deposition method was employed to develop a poly(ethylene glycol) (PEG)-like coating, which can act as a potential matrix for antimicrobial agents, by envisioning controlled-release food-packaging applications. Different plasma operating parameters, including the input power, monomer flow rate, and gap between the edge of the plasma head and substrate, were optimized to produce a PEG-like coating with a desirable water stability level and that can be biodegradable. The findings revealed that increased distance between the plasma head and substrate intensified gas-phase nucleation and diluted the active plasma species, which in turn led to the formation of a non-conformal rough coating. Conversely, at short plasma–substrate distances, smooth conformal coatings were obtained. Furthermore, at low input powers (<250 W), the chemical structure of the precursor was mostly preserved with a high retention of C-O functional groups due to limited monomer fragmentation. At the same time, these coatings exhibit low stability in water, which could be attributed to their low cross-linking degree. Increasing the power to 350 W resulted in the loss of the PEG-like chemical structure, which is due to the enhanced monomer fragmentation at high power. Nevertheless, owing to the enhanced cross-linking degree, these coatings were more stable in water. Finally, it could be concluded that a moderate input power (250–300 W) should be applied to obtain an acceptable tradeoff between the coating stability and PEG resemblance.
- 1 May 2023
- Published by International Society for Horticultural Science (ISHS) in Acta Horticulturae
- No. 1368,p. 25-32
Modified atmosphere storage of cut peony flowers to extend the sales period
ISHS XXXI International Horticultural Congress (IHC2022): International Symposium on Innovations in Ornamentals: from Breeding to Market Modified atmosphere storage of cut peony flowers to extend the sales period
- 1 May 2023
- Published by International Society for Horticultural Science (ISHS) in Acta Horticulturae
- No. 1368,p. 25-32
Modified atmosphere storage of cut peony flowers to extend the sales period
ISHS XXXI International Horticultural Congress (IHC2022): International Symposium on Innovations in Ornamentals: from Breeding to Market Modified atmosphere storage of cut peony flowers to extend the sales period
- 1 May 2023
- Published by International Society for Horticultural Science (ISHS) in Acta Horticulturae
- No. 1368,p. 7-18
Model selection for oxygen consumption by azalea cuttings and Echinacea plantlets in a closed system
ISHS XXXI International Horticultural Congress (IHC2022): International Symposium on Innovations in Ornamentals: from Breeding to Market Model selection for oxygen consumption by azalea cuttings and Echinacea plantlets in a closed system
- 1 May 2023
- Published by International Society for Horticultural Science (ISHS) in Acta Horticulturae
- No. 1368,p. 7-18
Model selection for oxygen consumption by azalea cuttings and Echinacea plantlets in a closed system
ISHS XXXI International Horticultural Congress (IHC2022): International Symposium on Innovations in Ornamentals: from Breeding to Market Model selection for oxygen consumption by azalea cuttings and Echinacea plantlets in a closed system
- Open Access
- 27 February 2023
- Published by Wiley in Packaging Technology and Science
- Vol. 36 (6) , 439-463
Scoring methodology for comparing the environmental performance of food packaging
- 27 February 2023
- Published by Wiley in Packaging Technology and Science
- Vol. 36 (6) , 439-463
Open AccessScoring methodology for comparing the environmental performance of food packaging
- 22 February 2021
- Published by Wiley in Packaging Technology and Science
- Vol. 34 (5) , 303-318
Selecting packaging material for dry food products by trade‐off of sustainability and performance: A case study on cookies and milk powder
Alternative packaging concepts for two dry, shelf‐stable food products were evaluated. A trade‐off between recyclability (monolayer materials) and performance (multilayered high‐barrier materials) was made for the packaging materials. Caramellized cookies were packaged in flowpacks made of PP film (OTR 1307 cc/m2/d, WVTR 5 g/m2/d), acryl‐coated PVdC/PP film (OTR 21.8 cc/m2/d, WVTR 4.2 g/m2/d) as a reference material and metallized PP (MPP) film (OTR 31.2 cc/m2/d, WVTR 0.4 g/m2/d) and stored at 22°C and 50% relative humidity. Texture was compromised after 6 months of storage for the former two materials, while the latter provided an extension of textural acceptability. Whole milk powder was packaged in unsealed PE bags as a reference, representing a typical paper bag with a PE liner that is stapled shut without a seal. Alternative packages were sealed PE bags (OTR 1464 cc/m2/d, WVTR 3 g/m2/d), PE/PA/EVOH/PA/PE (OTR 0.25 cc/m2/d, WVTR 0.95 g/m2/d) and PA/EVOH/PA/PE (OTR 1.24 cc/m2/d, WVTR 8 g/m2/d) multilayer bags, and PP/Al/PE (OTR 0.1 cc/m2/d, WVTR 0.1 g/m2/d) bags and stored at room temperature and relative humidity between 70% and 90%. Unsealed bags were found to be unacceptable for storage at high humidity, due to excessive caking, discolouration and mould growth. Sealed PE bags provided adequate protection against moisture, yet not against oxygen ingress, leading to oxidative off‐odours. The barrier efficiency of PA/EVOH/PA/PE was compromised by the high humidity. Both PE/PA/EVOH/PA/PE and PP/Al/PE bags provided adequate protection for over a year.
- 22 February 2021
- Published by Wiley in Packaging Technology and Science
- Vol. 34 (5) , 303-318
Selecting packaging material for dry food products by trade‐off of sustainability and performance: A case study on cookies and milk powder
Alternative packaging concepts for two dry, shelf‐stable food products were evaluated. A trade‐off between recyclability (monolayer materials) and performance (multilayered high‐barrier materials) was made for the packaging materials. Caramellized cookies were packaged in flowpacks made of PP film (OTR 1307 cc/m2/d, WVTR 5 g/m2/d), acryl‐coated PVdC/PP film (OTR 21.8 cc/m2/d, WVTR 4.2 g/m2/d) as a reference material and metallized PP (MPP) film (OTR 31.2 cc/m2/d, WVTR 0.4 g/m2/d) and stored at 22°C and 50% relative humidity. Texture was compromised after 6 months of storage for the former two materials, while the latter provided an extension of textural acceptability. Whole milk powder was packaged in unsealed PE bags as a reference, representing a typical paper bag with a PE liner that is stapled shut without a seal. Alternative packages were sealed PE bags (OTR 1464 cc/m2/d, WVTR 3 g/m2/d), PE/PA/EVOH/PA/PE (OTR 0.25 cc/m2/d, WVTR 0.95 g/m2/d) and PA/EVOH/PA/PE (OTR 1.24 cc/m2/d, WVTR 8 g/m2/d) multilayer bags, and PP/Al/PE (OTR 0.1 cc/m2/d, WVTR 0.1 g/m2/d) bags and stored at room temperature and relative humidity between 70% and 90%. Unsealed bags were found to be unacceptable for storage at high humidity, due to excessive caking, discolouration and mould growth. Sealed PE bags provided adequate protection against moisture, yet not against oxygen ingress, leading to oxidative off‐odours. The barrier efficiency of PA/EVOH/PA/PE was compromised by the high humidity. Both PE/PA/EVOH/PA/PE and PP/Al/PE bags provided adequate protection for over a year.
- Open Access
Oxygen Consumption by Phalaenopsis Plantlets and Chrysanthemum Cuttings as a Function of Temperature and Time: Model Structure Validation
Phalaenopsis spp. and Chrysanthemum are ornamentals with an important economic value. Currently, quality loss during storage and transport of plantlets and cuttings is a limiting factor for spreading the workload, broadening the export range, and the use of slower but more environmentally friendly transport. In the agro-food sector, equilibrium modified atmosphere packaging has enhanced the shelf-life of minimally processed produce. The required properties for an equilibrium modified atmosphere packaging system can be estimated from the respiration rate of the packaged commodity under specified atmospheric composition and storage temperature. In this work, a model structure is validated to estimate the respiration rate as a function of oxygen concentration and temperature for Phalaenopsis and Chrysanthemum. The oxygen concentration as a function of time was monitored in a closed system for different storage temperatures. The models show a good fit to the data. The model coefficients were dependent on the plant species and characteristics. The resulting formulae can be used to estimate the oxygen consumption rate of the produce under a range of oxygen concentrations and a temperature range from 15 °C to 32 °C for Phalaenopsis and from 2 °C to 14 °C for Chrysanthemum. The oxygen concentrations for which the formulae are valid depend on the storage temperature and plant species. The models can be used to estimate a dynamic oxygen consumption rate profile during storage and transport.
Open AccessOxygen Consumption by Phalaenopsis Plantlets and Chrysanthemum Cuttings as a Function of Temperature and Time: Model Structure Validation
Phalaenopsis spp. and Chrysanthemum are ornamentals with an important economic value. Currently, quality loss during storage and transport of plantlets and cuttings is a limiting factor for spreading the workload, broadening the export range, and the use of slower but more environmentally friendly transport. In the agro-food sector, equilibrium modified atmosphere packaging has enhanced the shelf-life of minimally processed produce. The required properties for an equilibrium modified atmosphere packaging system can be estimated from the respiration rate of the packaged commodity under specified atmospheric composition and storage temperature. In this work, a model structure is validated to estimate the respiration rate as a function of oxygen concentration and temperature for Phalaenopsis and Chrysanthemum. The oxygen concentration as a function of time was monitored in a closed system for different storage temperatures. The models show a good fit to the data. The model coefficients were dependent on the plant species and characteristics. The resulting formulae can be used to estimate the oxygen consumption rate of the produce under a range of oxygen concentrations and a temperature range from 15 °C to 32 °C for Phalaenopsis and from 2 °C to 14 °C for Chrysanthemum. The oxygen concentrations for which the formulae are valid depend on the storage temperature and plant species. The models can be used to estimate a dynamic oxygen consumption rate profile during storage and transport.