MOMichael G. Olsen

Michael G. Olsen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Michael G. Olsen has a total of 55 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Particulate Cake Formation and Pressure Development in Microfluidic Membrane Filters

    by Md Mohaimeen Ul Islam, Md Abdul Karim Miah, Michael G. Olsen, Jaime J. Juárez

    In filtering applications, particulates build up on the filtering membrane, forming a cake layer that directly affects permeability and increases pressure across the filter. In this investigation, 10 µm microchannels were fabricated using photolithography to create filters with porosities that vary between 9% and 23%. To estimate cake layer growth, a water–glycerol solution containing a 1% volume fraction of 15 µm polystyrene particles was injected by a syringe pump into filtration media at 300, 500 and 700 µL h−1 flow rates for 300 s. A differential pressure sensor was mounted across the inlet and outlet channels to measure transmembrane pressure (TMP) over time. It was found that higher flow rates accelerate particle deposition on the membrane surface, which contributes to a larger cake area and a corresponding rise in TMP. These findings will give valuable insights into clogging dynamics to optimize the filter’s efficiency and lifespan.

  • Open Access

    A stress‐balance‐based critical Weber number for droplets and bubbles

    by Supratim S. Dipta, Krishnamurthy Ravichandar, R. Dennis Vigil, Rodney O. Fox, Michael G. Olsen

    Predicting droplet and bubble breakup in turbulent flows is critical for optimizing multiphase flow processes such as emulsification and atomization. Traditional models based on a fixed critical Weber number () may not capture interfacial‐stress dominance in low‐viscosity fluids or viscous resistance in high‐viscosity droplets. This investigation provides the first direct, systematic validation of the stress‐balance criterion , obtained by combining Hinze stress scalings in an explicit three‐way force balance, in which the breakup threshold scales linearly with capillary number. This formulation provides a seamless framework applicable to both bubbles and droplets with moderate internal viscosity, and reduces reliance on regime‐specific empirical corrections by linking the breakup threshold directly to intrinsic fluid properties. Validation against experimental and simulation data, including bubbles and droplets, demonstrates good predictive accuracy for viscosity ratio up to at least , providing a generalized approach for turbulent multiphase flows.

  • Acoustic streaming micromixer with embedded obstacle arrays for dispersion enhancement

    by Md. Abdul Karim Miah, Md. Mohaimeen Ul Islam, Richa Ghosh, Chandra Tangudu, Michael G. Olsen, Jaime J. Juárez


  • Acoustic streaming flow driven about an array of sharp-edged obstacles

    by Abdul Karim Miah, Michael G. Olsen, Jaime J. Juárez


  • Open Access

    Microscopic Particle Image Velocimetry Analysis of Multiphase Flow in a Porous Media Micromodel

    by Abdul Karim Miah, Kawkab Ahasan, Todd A. Kingston, Michael G. Olsen, Jaime J. Juárez

    Pore-scale oil displacement behavior was investigated in a porous media micromodel using microscopic particle image velocimetry (mu PIV). Porous media micromodels consisting of an ordered square array of cylindrical pillars with 50 and 70% porosities were fabricated with photolithography. The oil displacement was performed with the injection of water at flow rates of 37.5, 75, and 150 mu L/h. These flow rates correspond to Reynolds number of 1.1 x 10(-2), 2.2 x 10(-2), and 4.4 x 10(-2), respectively in the 50% porous channel, and 1.84 x 10(-3), 3.69 x 10(-3), and 7.38 x 10(-3), respectively in the 70% porous channel. The capillary numbers for these flow rates are 2.18 x 10(-5), 4.36 x 10(-5), and 8.72 x 10(-5), respectively in the 50% porous channel, and 1.56 x 10(-5), 3.12 x 10(-5), and 6.23 x 10(-5), respectively in the 70% porous channel. The micromodel is initially saturated with oil, with the invading water phase following the path of least resistance as it displaces the oil. The mu PIV data were used to construct probability density functions (PDFs) which show an initial, nonzero, peak in transverse velocity as the water enters the micromodel. The PDFs broaden with time, indicating that the water is spreading, before retracting to a peak velocity of 0 mm/s, indicating that the water displacement has achieved equilibrium. We developed a model based on conservation of mass to describe the efficiency of the displacement process. All flow conditions demonstrate peak displacement efficiency when the amount of oil phase displacement is similar to 9 pore volumes in 50% porous channel and similar to 4 pore volumes in 70% porous channel.


  • Open Access

    Fitting parameter estimations for droplet breakage rate models

    by Krishnamurthy Ravichandar, R. Dennis Vigil, Michael G. Olsen

    Chemical process engineering unit operations such as solvent extraction, liquid–liquid chemical reactions, and emulsion processing are all dependent on turbulent liquid–liquid droplet flow dynamics. The design and operation of equipment used in these applications is often guided by theoretical models for droplet breakup. Although several models for droplet breakage in agitated liquid emulsions have been developed, their utility is limited because they incorporate fitting factors that must be determined empirically by performing experiments using a specific fluid pairing and relevant flow configuration. The need to acquire experimental data to determine model constants is a significant drawback that hinders widespread use of breakage models to design and optimize process equipment. In this work, analytical expressions are formulated to predict the value of a fitting parameter associated with droplet breakage time for two commonly used breakage rate models without having to perform empirical studies. These equations were derived by using the underlying assumptions within each of the two breakage models considered, namely, that droplet breakage is a result of the competition between relevant deformation and restorative stresses. Data from experiments conducted in a homogeneous turbulent von Kármán box as well as from previously published investigations of droplet breakage in heterogeneous flow devices were utilized to validate the derived equations for the breakage time parameters. In general, good agreement was observed between predictions obtained using the derived equations for fitting parameters and those obtained from experiments.


  • Open Access

    Acoustic driven circulation around cylindrical obstructions in microchannels

    by Abdul Karim Miah, Peter Zeller, Michael G. Olsen, Jaime J. Juárez

    We introduce an approach to generate direction-controlled circulation around cylindrical obstructions in channels using a piezoelectric transducer embedded porous-channel device fabricated by photolithography. To transmit acoustic signals into the channel, a single piezoelectric transducer was attached, operating at voltage levels of 5, 10, 15, and 20 V. Microscopic particle image velocimetry was employed to analyze the flow patterns in the channels. The analysis revealed two opposing circulation tendencies around the pillars located at two opposite sides of the channel in the longitudinal direction. The strength of circulation was found to be minimal in the middle of the channel and increased gradually toward the two ends of the channels. Furthermore, we observed that the circulation strength was maximum near the axial centerline and minimum at the boundaries along the width of the channels. Comparing the voltage levels, the higher voltage signals produced a higher strength of circulation than the lower voltage signals in all cases. Additionally, we found that the strength of circulation increased almost linearly and then decayed exponentially in the radial direction from the surfaces of the pillars. The observed velocity fields around individual cylinders matched well with the Görtler vortex model. The reported circulation phenomenon around pillars can be applied in non-contact fluid stirring and mixing in bio-chemical systems and lab-on-a-chip systems and may also provide additional degrees of freedom in object tweezing, trapping, and levitation.


  • Turbulent droplet breakage in a von Kármán flow cell

    by Krishnamurthy Ravichandar, R. Dennis Vigil, Rodney O. Fox, Stephanie Nachtigall, Andreas Daiss, Michal Vonka, Michael G. Olsen

    Droplet dispersion in liquid–liquid systems is a crucial step in many unit operations throughout the chemical, food, and pharmaceutic industries, where improper operation causes billions of dollars of loss annually. A theoretical background for the description of droplet breakup has been established, but many assumptions are still unconfirmed by experimental observations. In this investigation, a von Kármán swirling flow device was used to produce homogeneous, low-intensity turbulence suitable for carrying out droplet breakage experiments using optical image analysis. Individual droplets of known, adjustable, and repeatable sizes were introduced into an isotropic turbulent flow field providing novel control over two of the most important factors impacting droplet breakage: turbulence dissipation rate and parent droplet size. Introducing droplets one at a time, large data sets were gathered using canola, safflower, and sesame oils for the droplet phase and water as the continuous phase. Automated image analysis was used to determine breakage time, breakage probability, and child droplet size distribution for various turbulence intensities. Breakage time and breakage probability were observed to increase with increasing parent droplet size, consistent with the classic and widely used Coulaloglou–Tavlarides breakage model (C–T model). The shape of the child drop size distribution function was found to depend upon the size of the parent droplet.


  • Coherent structure characteristics of the swirling flow during turbulent mixing in a multi-inlet vortex reactor

    by Emmanuel Hitimana, Rodney O. Fox, James C. Hill, Michael G. Olsen

    Improving the efficiency of the production of uniformly sized functional nanoparticles for pharmaceutical and agricultural applications has been a problem of great interest. The macroscale multi-inlet vortex Reactor (macro-MIVR) could potentially be used for this purpose due to its ability to achieve the rapid mixing necessary for the flash nanoprecipitation nanoparticle fabrication technique. In the presented work, the coherent structures, a key contributor to the turbulent mixing, were investigated for the turbulent swirling flow within the MIVR. The two-point spatial correlations of velocity and concentration fluctuations at various basepoints were measured from instantaneous velocity and concentration fields obtained using simultaneous stereoscopic particle image velocimetry and planar laser-induced fluorescence. The basepoint locations were chosen as the middle and at the edge of the partially mixed concentration spiral arms. The correlations were found to be elliptical in shape, inclined, and peaked at the basepoints. A region near the basepoint was positively correlated and was surrounded by negatively correlated regions. Autocorrelations of concentration were also elliptical and curved toward the center of the reactor. The linear stochastic estimation was used to interpret the coherent structure features that would result in the observed spatial correlations. The linear stochastic estimates of the velocity fields were computed directly from the cross correlations of the tangential velocity fluctuations with the concentration fluctuations. The estimated conditional velocity fields revealed obliquely oriented counter-rotating vortical structures that stir the fluid from high-concentration regions to low-concentration regions, and the orientation of these vortical structures depended on the local concentration gradient.