Isao Takahashi
Research Subjects
Isao Takahashi has a total of 54 co-authors. Here are the top co-authors by number of shared publications:
- Noritaka Usami
Graduate School of Engineering
10 shared publications Kazuo Nakajima
Kyoto University 2 Graduate School of Energy Science Yoshida-Honmachi, Sakyo-ku, Kyoto 606-8501, Japan
7 shared publicationsKentaro Kutsukake
Tohoku University 1 Institute for Materials Research 2-1-1 Katahira, Aoba-ku, Sendai 980-8577, Japan
4 shared publications- Kozo Fujiwara
Institute for Material Science, Tohoku University, Sendai, Japan
3 shared publications Akira Yoshikawa
2 shared publicationsGaute Stokkan
Norwegian University of Science and Technology 2 , Alfred Getz vei 2, N-7491 Trondheim, Norway
2 shared publications
Latest Publications
- 22 December 2023
- Published by Elsevier in Journal of Crystal Growth
- Vol. 629
Heat transfer in β-Ga2O3 crystal grown through a skull melting method
- 22 December 2023
- Published by Elsevier in Journal of Crystal Growth
- Vol. 629
Heat transfer in β-Ga2O3 crystal grown through a skull melting method
- Open Access
Crucible-Free Growth of Bulk b-Ga2O3 Single-Crystal Scintillator under Oxidizing Atmosphere
β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of 3. In this study, 45 cm diameter β-Ga2O3 single crystals were prepared via oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.
Open AccessCrucible-Free Growth of Bulk b-Ga2O3 Single-Crystal Scintillator under Oxidizing Atmosphere
β-Ga2O3 is a well-known semiconductor material for power devices and other applications. Recently, β-Ga2O3 has also been reported as a scintillator material with a light yield of approximately 8400 ph./MeV, scintillation decay time of 3. In this study, 45 cm diameter β-Ga2O3 single crystals were prepared via oxide crystal growth using the cold crucible (OCCC) method under various oxygen partial pressures. In the OCCC method, as in the cold crucible method, a high frequency is applied directly to the oxide materials, which are heated and melted, and the melt is held by the outermost solid material itself that is cooled by water using a copper hearth. In the OCCC method, crystal growth is performed while rotating the seed crystal, as in the Czochralski method, to increase the crystal diameter. The optical properties and radiation responses of the crystals grown under various oxygen partial pressures were evaluated.
- 1 February 2023
- Published by Elsevier in Journal of Crystal Growth
- Vol. 609
3D calculation studies of dislocation density in a β-Ga2O3 crystal grown by vertical Bridgman method
- 1 February 2023
- Published by Elsevier in Journal of Crystal Growth
- Vol. 609
3D calculation studies of dislocation density in a β-Ga2O3 crystal grown by vertical Bridgman method
- 5 July 2018
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 57 (8S3) , 08RB12
Impact of boron incorporation on properties of silicon solar cells employing p-type polycrystalline silicon grown by aluminum-induced crystallization
We report on our attempt to increase the carrier density in the p-type polycrystalline silicon (poly-Si) layers grown by aluminum-induced crystallization (AIC) employing a B-doped Si target. Hall measurement revealed that we could obtain a lower-resistance and heavily doped p-type continuous poly-Si thin layer formed by AIC using B-doped a-Si. According to our evaluation of tunnel oxide passivated contact (TOPCon) solar cells with AIC-grown poly-Si, the AIC-TOPCon solar cells fabricated at 570 °C using B-doped a-Si showed higher conversion efficiency of 13.5% than that of 12.8% when using nondoped a-Si. It is considered that the cell characteristics, particularly FF and V oc , were improved owing to the lower series resistance and higher carrier density since both Al and B were successfully incorporated into the AIC-grown poly-Si.
- 5 July 2018
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 57 (8S3) , 08RB12
Impact of boron incorporation on properties of silicon solar cells employing p-type polycrystalline silicon grown by aluminum-induced crystallization
We report on our attempt to increase the carrier density in the p-type polycrystalline silicon (poly-Si) layers grown by aluminum-induced crystallization (AIC) employing a B-doped Si target. Hall measurement revealed that we could obtain a lower-resistance and heavily doped p-type continuous poly-Si thin layer formed by AIC using B-doped a-Si. According to our evaluation of tunnel oxide passivated contact (TOPCon) solar cells with AIC-grown poly-Si, the AIC-TOPCon solar cells fabricated at 570 °C using B-doped a-Si showed higher conversion efficiency of 13.5% than that of 12.8% when using nondoped a-Si. It is considered that the cell characteristics, particularly FF and V oc , were improved owing to the lower series resistance and higher carrier density since both Al and B were successfully incorporated into the AIC-grown poly-Si.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1794-1796
Solar Cells Application of p-type poly-Si Thin Film by Aluminum Induced Crystallization
We applied aluminum-induced crystallization (AIC) as a technique to realize heavily doped p-type polycrystalline Si layer at low temperature for the rear side of tunnel oxide passivated contact concept solar cell. Systematic temperature variation of AIC revealed that annealing at a temperature slightly lower than the eutectic temperature (577°C) is effective to improve solar cell performance. This is explained by reduced resistivity for low contact resistance while avoiding meltinz of AI-Si.
- 1 June 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1794-1796
Solar Cells Application of p-type poly-Si Thin Film by Aluminum Induced Crystallization
We applied aluminum-induced crystallization (AIC) as a technique to realize heavily doped p-type polycrystalline Si layer at low temperature for the rear side of tunnel oxide passivated contact concept solar cell. Systematic temperature variation of AIC revealed that annealing at a temperature slightly lower than the eutectic temperature (577°C) is effective to improve solar cell performance. This is explained by reduced resistivity for low contact resistance while avoiding meltinz of AI-Si.
- 21 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2522-2524
Application of new doping techniques to solar cells for low temperature fabrication
New techniques to fabricate highly doped p-type and n-type crystalline-Si (c-Si) layers at relatively low temperature were applied to solar cell devices. A very thin n-type emitter is formed by exposing phosphine (PH3) gas on c-Si surface around 600 °C. PH3 molecules can react with dangling bonds on the surface, and incorporate into shallow region in c-Si bulk. This thin doped layer is expected to decrease recombination near the surface. Another technique is aluminum induced crystallization to fabricate highly doped p-type c-Si layer which can dissolve Al atom up to the solubility limit. In this method, poly-crystalline Si of more than 100 μm grain size can be obtained around 500 °C. We applied these techniques to form pn-junction or back surface field of c-Si solar cells to reduce carrier recombination on c-Si surface and the parasitic optical absorption of these doped layers.
- 21 November 2016
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2522-2524
Application of new doping techniques to solar cells for low temperature fabrication
New techniques to fabricate highly doped p-type and n-type crystalline-Si (c-Si) layers at relatively low temperature were applied to solar cell devices. A very thin n-type emitter is formed by exposing phosphine (PH3) gas on c-Si surface around 600 °C. PH3 molecules can react with dangling bonds on the surface, and incorporate into shallow region in c-Si bulk. This thin doped layer is expected to decrease recombination near the surface. Another technique is aluminum induced crystallization to fabricate highly doped p-type c-Si layer which can dissolve Al atom up to the solubility limit. In this method, poly-crystalline Si of more than 100 μm grain size can be obtained around 500 °C. We applied these techniques to form pn-junction or back surface field of c-Si solar cells to reduce carrier recombination on c-Si surface and the parasitic optical absorption of these doped layers.
- 15 April 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 109 (8) , 083527
Implementation of faceted dendrite growth on floating cast method to realize high-quality multicrsytalline Si ingot for solar cells
We carried out small-scale crystal growth experiment to apply faceted dendrite growth at the top of the melt to floating cast method in order to grow high-quality multicrystalline Si (mc-Si) ingot for solar cells. By appropriate cooling at the initial stage, the most part of the top surface was covered by a single faceted dendrite crystal followed by directional solidification from the top to the bottom. As a consequence, the cross-section of the ingot was dominated by a single crystal grain. The crystal grain was found to be almost free from subgrain boundaries as evidenced by spatially resolved single-peak x-ray rocking curve profiles. The minority carrier diffusion length was found to be much longer than that in a control sample grown from the bottom to the top presumably due to the minimized contact with the crucible wall. This shows that the floating cast method combined with formation of faceted dendrite crystals at the initial stage is a promising route to realize high-quality mc-Si ingot for high-efficiency solar cells.
- 15 April 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 109 (8) , 083527
Implementation of faceted dendrite growth on floating cast method to realize high-quality multicrsytalline Si ingot for solar cells
We carried out small-scale crystal growth experiment to apply faceted dendrite growth at the top of the melt to floating cast method in order to grow high-quality multicrystalline Si (mc-Si) ingot for solar cells. By appropriate cooling at the initial stage, the most part of the top surface was covered by a single faceted dendrite crystal followed by directional solidification from the top to the bottom. As a consequence, the cross-section of the ingot was dominated by a single crystal grain. The crystal grain was found to be almost free from subgrain boundaries as evidenced by spatially resolved single-peak x-ray rocking curve profiles. The minority carrier diffusion length was found to be much longer than that in a control sample grown from the bottom to the top presumably due to the minimized contact with the crucible wall. This shows that the floating cast method combined with formation of faceted dendrite crystals at the initial stage is a promising route to realize high-quality mc-Si ingot for high-efficiency solar cells.
- 1 February 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 109 (3) , 033504
Impact of type of crystal defects in multicrystalline Si on electrical properties and interaction with impurities
We investigated impact of type of crystal defects in multicrystalline Si (mc-Si) on electrical properties and their change after gettering process of impurities. A bundle of dislocations gives negative impact on the gettering process, while grain boundaries does not affect at all. In addition, we categorized random grain boundaries in mc-Si by the contact angle between adjacent dendrite crystals to form the grain boundary. Change in the contrast of photoluminescence intensity around the grain boundary was found to systematically vary by the contact angle, which showed good correlation with calculated interface energy of the grain boundary. Grain boundaries with low interface energy are concluded to be preferable to weaken recombination activity by the gettering process and improvement of solar cell performance based on mc-Si.- 1 February 2011
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 109 (3) , 033504
Impact of type of crystal defects in multicrystalline Si on electrical properties and interaction with impurities
We investigated impact of type of crystal defects in multicrystalline Si (mc-Si) on electrical properties and their change after gettering process of impurities. A bundle of dislocations gives negative impact on the gettering process, while grain boundaries does not affect at all. In addition, we categorized random grain boundaries in mc-Si by the contact angle between adjacent dendrite crystals to form the grain boundary. Change in the contrast of photoluminescence intensity around the grain boundary was found to systematically vary by the contact angle, which showed good correlation with calculated interface energy of the grain boundary. Grain boundaries with low interface energy are concluded to be preferable to weaken recombination activity by the gettering process and improvement of solar cell performance based on mc-Si.- 1 April 2010
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 49 (4S) , 04DP01
Computational Investigation of Relationship between Shear Stress and Multicrystalline Structure in Silicon
We performed computational calculations by three-dimensional finite element analysis to investigate the relationship between the shear stress on slip planes and multicrystalline structural properties in Si, such as the grain orientation and the structure of the grain boundary. In our calculations, the change in multicrystalline structure is defined as the change in anisotropic elastic coefficient, which depends on the grain orientation. As a result, it becomes clear that the shear stress on slip planes depends on the grain orientation and concentrates near the grain boundary. Calculations in various multicrystalline structures reveal that controlling the growth direction in or has a great advantage for decreasing the shear stress on slip planes and resulting in the suppression of dislocation occurrence.
- 1 April 2010
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 49 (4S) , 04DP01
Computational Investigation of Relationship between Shear Stress and Multicrystalline Structure in Silicon
We performed computational calculations by three-dimensional finite element analysis to investigate the relationship between the shear stress on slip planes and multicrystalline structural properties in Si, such as the grain orientation and the structure of the grain boundary. In our calculations, the change in multicrystalline structure is defined as the change in anisotropic elastic coefficient, which depends on the grain orientation. As a result, it becomes clear that the shear stress on slip planes depends on the grain orientation and concentrates near the grain boundary. Calculations in various multicrystalline structures reveal that controlling the growth direction in or has a great advantage for decreasing the shear stress on slip planes and resulting in the suppression of dislocation occurrence.
- 1 March 2010
- Published by Elsevier in Journal of Crystal Growth
- Vol. 312 (7) , 897-901
Generation mechanism of dislocations during directional solidification of multicrystalline silicon using artificially designed seed
- 1 March 2010
- Published by Elsevier in Journal of Crystal Growth
- Vol. 312 (7) , 897-901
Generation mechanism of dislocations during directional solidification of multicrystalline silicon using artificially designed seed