Zi Ye Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zi Ye Liu has a total of 51 co-authors. Here are the top co-authors by number of shared publications:
Y.B. Guo
12 shared publications- Michael Patrick Sealy
University of Nebraska-Lincoln, Lincoln, NE
9 shared publications - Yuebin B. Guo
Rutgers University-New Brunswick Department of Mechanical, and Aerospace Engineering Piscataway, NJ 08854
9 shared publications Bin Zou
6 shared publicationsC. Li
5 shared publicationsZ.Y. Liu
Dept. of Mechanical Engineering, The University of Alabama, Tuscaloosa, AL 35487, USA
5 shared publications
Latest Publications
- 19 May 2023
- Published by Elsevier in Atmospheric Environment
- Vol. 307, 119849
Distribution characteristics of secondary organic aerosol tracers in PM2.5 in Jinzhong
- 19 May 2023
- Published by Elsevier in Atmospheric Environment
- Vol. 307, 119849
Distribution characteristics of secondary organic aerosol tracers in PM2.5 in Jinzhong
- 1 January 2019
- Published by Elsevier in CIRP Annals
- Vol. 68 (1) , 455-458
Heterogeneous data-driven hybrid machine learning for tool condition prognosis
- 1 January 2019
- Published by Elsevier in CIRP Annals
- Vol. 68 (1) , 455-458
Heterogeneous data-driven hybrid machine learning for tool condition prognosis
- 1 October 2018
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 35, 500-507
Energy consumption characteristics in finish hard milling
- 1 October 2018
- Published by Elsevier in Journal of Manufacturing Processes
- Vol. 35, 500-507
Energy consumption characteristics in finish hard milling
- 1 April 2018
- Published by Elsevier in Journal of Cleaner Production
- Vol. 181, 329-336
Cumulative energy demand and environmental impact in sustainable machining of inconel superalloy
- 1 April 2018
- Published by Elsevier in Journal of Cleaner Production
- Vol. 181, 329-336
Cumulative energy demand and environmental impact in sustainable machining of inconel superalloy
- 13 February 2018
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 140 (4)
On the Simulation Scalability of Predicting Residual Stress and Distortion in Selective Laser Melting
Rapid heating and cooling thermal cycle of metals in selective laser melting (SLM) generates high tensile residual stress which leads to part distortion. However, how to fast and accurately predict residual stress and the resulted part distortion remains a critical issue. It is not practical to simulate every single laser scan to build up a functional part due to the exceedingly high computational cost. Therefore, scaling up the material deposition rate via increasing heat source dimension and layer thickness would dramatically reduce the computational cost. In this study, a multiscale scalable modeling approach has been developed to enable fast prediction of part distortion and residual stress. Case studies on residual stress and distortion of the L-shaped bar and the bridge structure were presented via the deposition scalability and validation with the experimental data. High residual stress gradient in the building direction was found from high tensile on the surface to high compressive in the core. The part distortion can be predicted with reasonable accuracy when the block thickness is scaled up by 50 times the layer thickness from 30 μm to 1500 μm. The influence of laser scanning strategy on residual stress distribution and distortion magnitude of the bridges has shown that orthogonal scanning pattern between two neighboring block layers is beneficial for reducing part distortion.
- 13 February 2018
- Published by ASME International in Journal of Manufacturing Science and Engineering
- Vol. 140 (4)
On the Simulation Scalability of Predicting Residual Stress and Distortion in Selective Laser Melting
Rapid heating and cooling thermal cycle of metals in selective laser melting (SLM) generates high tensile residual stress which leads to part distortion. However, how to fast and accurately predict residual stress and the resulted part distortion remains a critical issue. It is not practical to simulate every single laser scan to build up a functional part due to the exceedingly high computational cost. Therefore, scaling up the material deposition rate via increasing heat source dimension and layer thickness would dramatically reduce the computational cost. In this study, a multiscale scalable modeling approach has been developed to enable fast prediction of part distortion and residual stress. Case studies on residual stress and distortion of the L-shaped bar and the bridge structure were presented via the deposition scalability and validation with the experimental data. High residual stress gradient in the building direction was found from high tensile on the surface to high compressive in the core. The part distortion can be predicted with reasonable accuracy when the block thickness is scaled up by 50 times the layer thickness from 30 μm to 1500 μm. The influence of laser scanning strategy on residual stress distribution and distortion magnitude of the bridges has shown that orthogonal scanning pattern between two neighboring block layers is beneficial for reducing part distortion.
- Open Access
- 1 January 2018
- Published by Elsevier in Procedia Manufacturing
- Vol. 26, 834-845
Energy Consumption in Additive Manufacturing of Metal Parts
- 1 January 2018
- Published by Elsevier in Procedia Manufacturing
- Vol. 26, 834-845
Open AccessEnergy Consumption in Additive Manufacturing of Metal Parts
- Open Access
- 1 January 2018
- Published by Elsevier in Procedia CIRP
- Vol. 71, 348-353
Residual Stress in Metal Additive Manufacturing
- 1 January 2018
- Published by Elsevier in Procedia CIRP
- Vol. 71, 348-353
Open AccessResidual Stress in Metal Additive Manufacturing
- 1 January 2018
- Published by Elsevier in CIRP Annals
- Vol. 67 (1) , 57-60
A hybrid approach to integrate machine learning and process mechanics for the prediction of specific cutting energy
- 1 January 2018
- Published by Elsevier in CIRP Annals
- Vol. 67 (1) , 57-60
A hybrid approach to integrate machine learning and process mechanics for the prediction of specific cutting energy
- 14 December 2017
- Published by Taylor & Francis
- p. 499-514
Big Data Analysis for Smart Manufacturing
The emerging paradigm of smart manufacturing creates and uses data and information throughout the product life cycle with the goal of rapid manufacturing of new products, dynamic response to product demand, and real-time optimization of manufacturing production and supply chain networks. Smart manufacturing has the potential to fundamentally change how products are designed, manufactured, supplied, used, remanufactured, and eventually retired. Smart manufacturing utilizes big data analytics, to refine complicated processes and manage supply chains [1]. Big data analytics refers to a method for gathering and understanding large data sets in terms of velocity, variety, and volume. Big data analytics allows an enterprise to use smart manufacturing to shift from reactionary practices to predictive ones, a change that targets improved efficiency of the process and performance of the product [2].
- 14 December 2017
- Published by Taylor & Francis
- p. 499-514
Big Data Analysis for Smart Manufacturing
The emerging paradigm of smart manufacturing creates and uses data and information throughout the product life cycle with the goal of rapid manufacturing of new products, dynamic response to product demand, and real-time optimization of manufacturing production and supply chain networks. Smart manufacturing has the potential to fundamentally change how products are designed, manufactured, supplied, used, remanufactured, and eventually retired. Smart manufacturing utilizes big data analytics, to refine complicated processes and manage supply chains [1]. Big data analytics refers to a method for gathering and understanding large data sets in terms of velocity, variety, and volume. Big data analytics allows an enterprise to use smart manufacturing to shift from reactionary practices to predictive ones, a change that targets improved efficiency of the process and performance of the product [2].