BOBieke Onghena

Bieke Onghena

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bieke Onghena has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Selective leaching of lead from lead smelter residues using EDTA

    by Thupten Palden, Lieven Machiels, Bieke Onghena, Mercedes Regadío, Koen Binnemans

    Ethylenediaminetetraacetic acid (EDTA) has been widely used as an effective reagent for removal of lead from soil because of its high lead extraction efficiency caused by the high thermodynamic stability of the Pb(II)–EDTA complex. In this study, EDTA was used as a lixiviant for recovery of lead from residues (matte and slag) of secondary lead smelter plants. The residues were composed mainly of iron (34–66 wt%) and lead (7–11 wt%). Leaching parameters (EDTA concentration, pH, temperature, liquid-to-solid ratio and leaching time) were optimized. The optimum leaching efficiency was achieved when leached for 1 h at room temperature using 0.05 mol L−1 EDTA at a liquid-to-solid ratio of 5 mL g−1. At such conditions, 72 to 80% of lead and less than 1% of iron were leached from both matte and slag. The high selectivity towards lead with minimal co-dissolution of iron is a major advantage since it reduces the chemical consumption and simplifies the downstream processes. Although the stability constants of the complexes Fe(III)–EDTA, Fe(II)–EDTA and Pb–EDTA are all large (log KS 25.1, 14.33 and 18.04, respectively), the leaching of iron was most likely limited by its presence in insoluble phases such as iron oxides, sulfides and silicates in the residues. 100% leaching of lead was achieved by a multi-step leaching process where the leaching residues were contacted three times by a fresh EDTA solution. To recover EDTA, first iron was precipitated as iron hydroxide by raising the pH of pregnant leach solution (PLS) above 12.6 using sodium hydroxide, followed by precipitation of lead as lead sulfide by adding ammonium sulfide. The recovered EDTA was successfully reused two times for leaching without significant changes in leaching yields.


  • Open Access

    Cation Effect of Chloride Salting Agents on Transition Metal Ion Hydration and Solvent Extraction by the Basic Extractant Methyltrioctylammonium Chloride

    by Rayco Lommelen, Bieke Onghena, Koen Binnemans

    The addition of a nonextractable salt has an important influence on the solvent extraction of metal ions, but the underlying principles are not completely understood yet. However, relating solute hydration mechanisms to solvent extraction equilibria is key to understanding the mechanism of solvent extraction of metal ions as a whole. We have studied the speciation of Co(II), Zn(II), and Cu(II) in aqueous solutions containing different chloride salts to understand their extraction to the basic extractant methyltrioctylammonium chloride (TOMAC). This includes the first speciation profile of Zn(II) in chloride media with the three Zn(II) species [Zn(H2O)6]2+, [ZnCl3H2O]−, and [ZnCl4]2–. The observed differences in extraction efficiency for a given transition metal ion can be explained by transition metal ion hydration due to ion–solvent interactions, rather than by ion–solute interactions or by differences in speciation. Chloride salting agents bearing a cation with a larger hydration Gibbs free energy reduce the free water content more, resulting in a lower hydration for the transition metal ion. This destabilizes the transition metal chloro complex in the aqueous phase and increases the extraction efficiency. Salting agents with di- and trivalent cations reduce the transition metal chloro complex hydration less than expected, resulting in a lower extraction efficiency. The cations of these salting agents have a very large hydration Gibbs free energy, but the overall hydration of these salts is reduced due to significant salt ion pair formation. The general order of salting-out strength for the extraction of metal ions from chloride salt solutions is Cs+ < Rb+ < NH4+ ≈ K+ < Al3+ ≈ Mg2+ ≈ Ca2+ ≈ Na+ < Li+. These findings can help in predicting the optimal conditions for metal separation by solvent extraction and also contribute to a broader understanding of the effects of dissolved salts on solutes.


  • Open Access

    Non-aqueous solvent extraction of indium from an ethylene glycol feed solution by the ionic liquid Cyphos IL 101: speciation study and continuous counter-current process in mixer–settlers

    by Clio Deferm, Bieke Onghena, Viet Tu Nguyen, Dipanjan Banerjee, Jan Fransaer, Koen Binnemans

    A solvometallurgical process for the separation of indium(III) and zinc(II) from ethylene glycol solutions using the ionic liquid extractants Cyphos IL 101 and Aliquat 336 in an aromatic diluent has been investigated. The speciation of indium(III) in the two immiscible organic phases was investigated by Raman spectroscopy, infrared spectroscopy, EXAFS and 115In NMR spectroscopy. At low LiCl concentrations in ethylene glycol, the bridging (InCl3)2(EG)3 or mononuclear (InCl3)(EG)2 complex is proposed. At higher lithium chloride concentrations, the first coordination sphere changes to two oxygen atoms from one bidentate ethylene glycol ligand and four chloride anions ([In(EG)Cl4]−). In the less polar phase, indium(III) is present as a tetrahedral [InCl4]− complex independent of the LiCl concentration. After the number of theoretical stages had been determined using a McCabe–Thiele diagram for extraction by Cyphos IL 101, the extraction and scrubbing processes were performed in lab-scale mixer–settlers to test the feasibility of working in continuous mode. Indium(III) was extracted quantitatively in four stages, with 19% co-extraction of zinc(II). The co-extracted zinc(II) was scrubbed selectively in six stages using an indium(III) scrub solution. Indium(III) was recovered from the loaded less polar organic phase as indium(III) hydroxide (98.5%) by precipitation stripping with an aqueous NaOH solution.


  • Open Access

    Selective recovery of zinc from goethite residue in the zinc industry using deep-eutectic solvents

    by Nerea Rodriguez Rodriguez, Lieven Machiels, Bieke Onghena, Jeroen Spooren, Koen Binnemans

    Several deep-eutectic solvents (DESs) were tested for the valorisation of goethite residue produced by the zinc industry. The objective of the work was to selectively recover zinc from the iron-rich matrix using deep-eutectic solvents as lixiviants. The effect of the type of hydrogen bond donor and hydrogen bond acceptor of the deep-eutectic solvent on the leaching efficiency was studied. Levulinic acid–choline chloride (xChCl = 0.33) (LevA–ChCl) could selectively leach zinc from the iron-rich matrix, and it was selected as the best-performing system to be used in further study. The leaching process was optimised in terms of temperature, contact time, liquid-to-solid ratio and water content of the deep-eutectic solvent. The role of the choline cation on the leaching process was investigated by considering the leaching properties of a LevA–CaCl2 mixture. The goethite residue was also leached with pure levulinic acid. The results were compared to a purely hydrometallurgical approach using sulphuric acid leaching. Leaching with LevA–ChCl resulted in higher selectivity compared to the conventional “hot leaching” with 80 g L−1 sulphuric acid. Furthermore, a slightly higher zinc recovery and comparable selectivity for zinc over iron were achieved with LevA–ChCl compared to conventional “neutral leaching” with 10 g L−1 sulphuric acid.


  • Open Access

    Recovery of Lead and Silver from Zinc Leaching Residue Using Methanesulfonic Acid

    by Nerea Rodriguez Rodriguez, Bieke Onghena, Koen Binnemans

    A solvometallurgical route for the recovery of lead and silver from the leaching residue of the zinc roast-leach-electrowin process was developed. Methanesulfonic acid was selected as lixiviant due to the high solubility of lead and silver methanesulfonate salts. The direct leaching of the residue with methanesulfonic acid showed a high co-dissolution of gypsum and a low dissolution of lead (present as anglesite), requiring a high liquid-to-solid ratio. Two pretreatment processes were investigated to improve the leaching efficiency. First, the gypsum was selectively removed via Randall extraction using water as a solvent. Pure gypsum was obtained in this step, and the solvent could be reused multiple times. Secondly, the solubility of lead was increased by transforming the anglesite into cerussite via a carbonation reaction with sodium carbonate. When the carbonation reaction was performed before the removal of gypsum, a significant excess of sodium carbonate was required, because the gypsum was also transformed into calcium carbonate. However, when the carbonation was done on the gypsum-free material, a stoichiometric amount of sodium carbonate was sufficient. The carbonation reaction drastically increased the lead dissolution, and the liquid-to-solid ratio requirements decreased. The leaching efficiency for both silver and lead using methanesulfonic acid as lixiviant after Randall extraction and the carbonation reaction was around 80%.


  • Methanesulfonic acid: a sustainable acidic solvent for recovering metals from the jarosite residue of the zinc industry

    by Thupten Palden, Bieke Onghena, Mercedes Regadío, Koen Binnemans

    Methanesulfonic acid (MSA) is a green acid with a remarkably high solubility for several speciality and base metals including lead, making it an interesting leaching agent for metals. MSA is safer and less toxic than the mineral acids (HCl, H2SO4, HNO3) currently employed for leaching metals from primary and secondary sources. In this study, MSA was tested for the leaching of lead and zinc from the iron-rich jarosite residue of the zinc industry. The leaching of lead, zinc and iron increased as a function of the MSA concentration in water up to 90 vol% MSA. Higher MSA concentrations resulted in precipitate formation due to the limited solubility of the iron and zinc methanesulfonate salts in water-lean MSA. Leaching with pure MSA resulted in a pregnant leach solution (PLS) comprising most of the lead and zinc, and a precipitate comprising the majority of the iron and a fraction of the zinc originally present in the jarosite. The optimization of the leaching conditions showed that increasing the liquid-to-solid ratio or temperature increased the leaching efficiencies of the metals, especially of lead. The leaching under optimized conditions was successfully performed on a larger scale using a temperature-controlled batch leaching reactor. The metal/iron mass ratio increased from 1/4 for Pb/Fe, and from 1/7 for Zn/Fe in the initial jarosite, to over 2.66/1 and 1/2, in the PLS, respectively. The remaining MSA in the PLS was recovered by vacuum distillation and successfully reused for three leaching cycles.


  • Open Access

    Model for Metal Extraction from Chloride Media with Basic Extractants: A Coordination Chemistry Approach

    by Rayco Lommelen, Tom Vander Hoogerstraete, Bieke Onghena, Isabelle Billard, Koen Binnemans

    The metal extraction mechanism of basic extractants is typically described as an anion exchange process, but this mechanism does not correctly explain all observations. This paper introduces a novel model for the extraction of metals by basic extractants from chloride media supported by experimental data on methyltrioctylammonium chloride and Aliquat 336 chloride systems. This model relies on the hypothesis that the metal species least stabilized in the aqueous phase by hydration (i.e., the metal species with the lowest charge density) is extracted more efficiently than the more water stabilized species (i.e., species with higher charge densities). Once it is transferred to the organic phase, the extracted species can undergo further Lewis acid–base adduct formation reactions with the chloride anions available in the organic phase to form negatively charged chloro complexes, which than associate with the organic cations. Salting-out agents influence the extraction, most likely by decreasing the concentration of free water molecules, which destabilizes the metal complex in the aqueous phase. The evidence provided includes (1) the link between extraction and transition-metal speciation, (2) the trend in extraction efficiency as a function of the concentration of different salting-out agents, and (3) the behavior of HCl in the extraction system. The proposed extraction model better explains the experimental observations in comparison to the anion exchange model and allows the prediction of optimal conditions for metal extractions and separations a priori, by selecting the most suitable salting-out agent and its concentration.


  • Open Access

    Enhancing Metal Separations Using Hydrophilic Ionic Liquids and Analogues as Complexing Agents in the More Polar Phase of Liquid–Liquid Extraction Systems

    by Zheng Li, Bieke Onghena, Xiaohua Li, Zidan Zhang, Koen Binnemans

    The separation of metals by liquid–liquid extraction largely relies on the affinity of metals to the extractants, which normally reside in the organic (less polar) phase because of their high hydrophobicity. Following a different route, using aminopoly(carboxylic acid)s (e.g., EDTA) as complexing agents in the aqueous (more polar) phase was found to enhance metal separations by selectively complexing metal cations. In this study, we demonstrate that, hydrophilic ionic liquids and analogues in the more polar phase could also selectively complex with metal cations and hence enhance metal separations. As an example, Cyanex 923 (a mixture of trialkyl phosphine oxides) dissolved in p-cymene extracts CoCl2 more efficiently than SmCl3 from a chloride ethylene glycol (EG) solution. However, when tetraethylammonium chloride is added into the EG solution, CoCl2 is selectively held back (only 1.2% extraction at 3.0 M tetraethylammonium chloride), whereas the extraction of SmCl3 is unaffected (89.9% extraction), leading to reversed metal separation with a separation factor of Sm(III)/Co(II) > 700. The same principle is applicable to a range of hydrophilic ionic liquids, which can be used as complexing agents in the more polar phase to enhance the separations of various metal mixtures by liquid–liquid extraction.


  • Open Access

    Recovery of cobalt from dilute aqueous solutions using activated carbon–alginate composite spheres impregnated with Cyanex 272

    by Stijn Van Roosendael, Bieke Onghena, Joris Roosen, Bart Michielsen, Kenny Wyns, Steven Mullens, Koen Binnemans

    Waste water was purified from cobalt(ii) and manganese(ii) by adsorption and desorption on shaped and impregnated activated carbon spheres.


  • Open Access

    Electrodeposition of indium from the ionic liquid trihexyl(tetradecyl)phosphonium chloride

    by Clio Deferm, João C. Malaquias, Bieke Onghena, Dipanjan Banerjee, Jan Luyten, Harald Oosterhof, Jan Fransaer, Koen Binnemans

    The two-step reduction of indium(iii) in the ionic liquid trihexyl(tetradecyl)phosphonium chloride resulted in droplet deposition.