Rafael Barbosa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Rafael Barbosa has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Matheus Colovati Saccardo
Federal University of Sao Carlos, Graduate Program in Materials Science and Engineering, São Carlos, São Paulo, Brazil
8 shared publications - Roger Gonçalves
Federal University of Sao Carlos, Graduate Program in Materials Science and Engineering, São Carlos, São Paulo, Brazil
8 shared publications - Carlos Henrique Scuracchio
Federal University of Sao Carlos, Graduate Program in Materials Science and Engineering, São Carlos, São Paulo, Brazil
6 shared publications - Kaique Afonso Tozzi
Laboratoire de Physicochimie des Polymères et des Interfaces (LPPI), Université de Cergy-Pontoise, 5 mail Gay, Lussac, F-95031 Cergy-Pontoise-Cedex, France
6 shared publications - Ariel Gustavo Zuquello
Polytechnic School, Community University of Chapecó Region, Chapecó, Brazil
5 shared publications - Guilherme Eduardo de Oliveira Blanco
Federal University of Sao Carlos, Graduate Program in Materials Science and Engineering, São Carlos, São Paulo, Brazil
4 shared publications
Latest Publications
- 1 October 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (10) , 105013
Design and performance of an electromechanical sensor using sulfonated PEEK-based IPMC with ionic liquid integration
Ionomeric polymer–metal composites (IPMCs) are electroactive materials extensively studied for sensing and actuation applications. While Nafion® is the most used ionomer in IPMCs, its high cost and environmental impact have motivated research into alternative materials. This work introduces a novel composite membrane formed by integrating the ionic liquid 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) into a highly sulfonated poly(ether ether ketone) (SPEEK) matrix (90.7% degree of sulfonation). The performance of this novel composite membrane as an electromechanical sensor was systematically evaluated. The fabricated IPMCs demonstrated the electrochemical stability to operate under voltages up to 5 V without evidence of water hydrolysis, addressing a common limitation of conventional H+-based IPMCs. Additionally, electromechanical sensing tests showed that BMIM-based IPMCs effectively detected motion trajectories (linear, cubic, and quadratic) and frequencies from 0.08 to 2 Hz. The BMIM-BMIM+ system exhibited an exceptionally high sensing response, reaching potential amplitudes 100 times greater than conventional Nafion®-H+ IPMCs. These findings highlight the potential of SPEEK-IL as a promising alternative for high-performance electroactive devices.
- 1 October 2025
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 34 (10) , 105013
Design and performance of an electromechanical sensor using sulfonated PEEK-based IPMC with ionic liquid integration
Ionomeric polymer–metal composites (IPMCs) are electroactive materials extensively studied for sensing and actuation applications. While Nafion® is the most used ionomer in IPMCs, its high cost and environmental impact have motivated research into alternative materials. This work introduces a novel composite membrane formed by integrating the ionic liquid 1-butyl-3-methylimidazolium chloride ([BMIM]Cl) into a highly sulfonated poly(ether ether ketone) (SPEEK) matrix (90.7% degree of sulfonation). The performance of this novel composite membrane as an electromechanical sensor was systematically evaluated. The fabricated IPMCs demonstrated the electrochemical stability to operate under voltages up to 5 V without evidence of water hydrolysis, addressing a common limitation of conventional H+-based IPMCs. Additionally, electromechanical sensing tests showed that BMIM-based IPMCs effectively detected motion trajectories (linear, cubic, and quadratic) and frequencies from 0.08 to 2 Hz. The BMIM-BMIM+ system exhibited an exceptionally high sensing response, reaching potential amplitudes 100 times greater than conventional Nafion®-H+ IPMCs. These findings highlight the potential of SPEEK-IL as a promising alternative for high-performance electroactive devices.
- 25 May 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (31)
Beyond static: Tracking the dynamic nature of water absorption and Young's modulus in IPMC devices
Ionomeric polymer‐metal composites (IPMC) are advanced materials designed to mimic biological systems. Their performance depends on various factors, including electrical stimulus intensity, membrane hydration, ionic migration, and Young's modulus. However, there is a lack of studies in the literature investigating how the water absorption capacity and elastic modulus change over time in IPMCs. Understanding the hydration level variation as a function of time is essential because as this parameter deviates, the ionic migration capacity and Young's modulus also change, altering the device's electromechanical efficiency over time. To address this research gap, Nafion/Pt‐based IPMC devices exchanged with four monovalent cations (H+, Li+, Na+, and K+) and one ionic liquid (1‐butyl‐3‐methylimidazolium—BMIM+) were prepared, and a comprehensive investigation on how the water absorption capacity and Young's modulus vary as a function of time, relative humidity (RH), and counterion size was performed. The results revealed that the water uptake capacity is significantly higher and occurs more rapidly at higher RH levels and when the counterion's ionic radius decreases. Consequently, the time required for the device to reach osmotic equilibrium can range from 40 to 270 min, depending on the RH and counterion used. Furthermore, it was observed that the first natural frequency and Young's modulus also exhibit time‐dependent behavior. Under constant RH conditions, the mechanical properties of the IPMC can vary by up to 50% in less than 60 min. Notably, the combined results from water uptake capacity, Young's modulus, electrochemical impedance spectroscopy, and electromechanical response analyses (including blocking force, displacement, displacement rate, current, coulombic efficiency, and voltage) suggest that a morphological transformation within the polymer is likely to occur once RH exceeds 60%. This finding strengthens the hypothesis that ion migration is mainly influenced by their movement through Nafion's ionomeric channels rather than the filling of ionic agglomerates.
- 25 May 2024
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 141 (31)
Beyond static: Tracking the dynamic nature of water absorption and Young's modulus in IPMC devices
Ionomeric polymer‐metal composites (IPMC) are advanced materials designed to mimic biological systems. Their performance depends on various factors, including electrical stimulus intensity, membrane hydration, ionic migration, and Young's modulus. However, there is a lack of studies in the literature investigating how the water absorption capacity and elastic modulus change over time in IPMCs. Understanding the hydration level variation as a function of time is essential because as this parameter deviates, the ionic migration capacity and Young's modulus also change, altering the device's electromechanical efficiency over time. To address this research gap, Nafion/Pt‐based IPMC devices exchanged with four monovalent cations (H+, Li+, Na+, and K+) and one ionic liquid (1‐butyl‐3‐methylimidazolium—BMIM+) were prepared, and a comprehensive investigation on how the water absorption capacity and Young's modulus vary as a function of time, relative humidity (RH), and counterion size was performed. The results revealed that the water uptake capacity is significantly higher and occurs more rapidly at higher RH levels and when the counterion's ionic radius decreases. Consequently, the time required for the device to reach osmotic equilibrium can range from 40 to 270 min, depending on the RH and counterion used. Furthermore, it was observed that the first natural frequency and Young's modulus also exhibit time‐dependent behavior. Under constant RH conditions, the mechanical properties of the IPMC can vary by up to 50% in less than 60 min. Notably, the combined results from water uptake capacity, Young's modulus, electrochemical impedance spectroscopy, and electromechanical response analyses (including blocking force, displacement, displacement rate, current, coulombic efficiency, and voltage) suggest that a morphological transformation within the polymer is likely to occur once RH exceeds 60%. This finding strengthens the hypothesis that ion migration is mainly influenced by their movement through Nafion's ionomeric channels rather than the filling of ionic agglomerates.
- 17 January 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (2) , 025008
Novel IP2C sensors with flexible electrodes based on plasma-treated conductive elastomeric nanocomposites
Ionic polymer-metal composites (IPMC) are devices composed of metallic electrodes and an ionomeric polymer membrane in a ‘sandwich’ architecture and. Their main property is electromechanical actuation or sensing based on the movement of ions. Metallic electrodes are commonly used for their high electrical conductivity, malleability, and chemical resistance. However, the high cost of noble metals, such as platinum, long manufacturing time, and fatigue failure limit their application. Therefore, the replacement of metallic electrodes with conductive elastomeric nanocomposites (CENs) was evaluated to reduce the costs and complexity of manufacturing the device and increase its working life. In this work, carbon nanotubes were used as the conductive fillers. The dispersion to achieve high electrical conductivity was carried out directly in the synthetic or natural polyisoprene rubber latex assisted by surfactant and high-power sonication. To improve the adhesion between the elastomeric electrode and the ionic membrane (Nafion), plasma treatment with atmospheric air was applied as a surface modifier. This treatment improved the hydrophilicity and adhesion of the rubbers by forming oxygenated groups and increasing the surface nanoroughness. In this way, ionomeric polymer–polymer composite (IP2C) devices were fabricated using Nafion and plasma-modified CENs, this type of electrode is unprecedented in the literature for this application. These devices showed displacement and strain sensing capacity at levels close to the conventional IPMC in all tested frequency ranges and applied accelerations. Notably, the IP2C obtained better resolution at low frequencies than the control.
- 17 January 2024
- Published by IOP Publishing in Smart Materials and Structures
- Vol. 33 (2) , 025008
Novel IP2C sensors with flexible electrodes based on plasma-treated conductive elastomeric nanocomposites
Ionic polymer-metal composites (IPMC) are devices composed of metallic electrodes and an ionomeric polymer membrane in a ‘sandwich’ architecture and. Their main property is electromechanical actuation or sensing based on the movement of ions. Metallic electrodes are commonly used for their high electrical conductivity, malleability, and chemical resistance. However, the high cost of noble metals, such as platinum, long manufacturing time, and fatigue failure limit their application. Therefore, the replacement of metallic electrodes with conductive elastomeric nanocomposites (CENs) was evaluated to reduce the costs and complexity of manufacturing the device and increase its working life. In this work, carbon nanotubes were used as the conductive fillers. The dispersion to achieve high electrical conductivity was carried out directly in the synthetic or natural polyisoprene rubber latex assisted by surfactant and high-power sonication. To improve the adhesion between the elastomeric electrode and the ionic membrane (Nafion), plasma treatment with atmospheric air was applied as a surface modifier. This treatment improved the hydrophilicity and adhesion of the rubbers by forming oxygenated groups and increasing the surface nanoroughness. In this way, ionomeric polymer–polymer composite (IP2C) devices were fabricated using Nafion and plasma-modified CENs, this type of electrode is unprecedented in the literature for this application. These devices showed displacement and strain sensing capacity at levels close to the conventional IPMC in all tested frequency ranges and applied accelerations. Notably, the IP2C obtained better resolution at low frequencies than the control.
- 13 October 2022
- Published by Elsevier in Electrochimica Acta
- Vol. 435
Multi-sensing properties of hybrid filled natural rubber nanocomposites using impedance spectroscopy
- 13 October 2022
- Published by Elsevier in Electrochimica Acta
- Vol. 435
Multi-sensing properties of hybrid filled natural rubber nanocomposites using impedance spectroscopy
- 12 October 2022
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 53 (2) , 241-255
Improving electrochemical stability and electromechanical efficiency of ipmcs: tuning ionic liquid concentration
- 12 October 2022
- Published by Springer Nature in Journal of Applied Electrochemistry
- Vol. 53 (2) , 241-255
Improving electrochemical stability and electromechanical efficiency of ipmcs: tuning ionic liquid concentration
- 10 March 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (23)
Improving the swelling, mechanical, and electrical properties in natural rubber latex/carbon nanotubes nanocomposites: Effect of the sonication method
Conductive polymeric composites are exciting for future electronic applications given the possibility to ally electrical conductivity and flexibility. However, the high viscosity of plasticized elastomers difficult the dispersion of conductive fillers in an elastomeric matrix is difficult. This research aimed to compare the use of bath or probe sonication to disperse multi‐walled carbon nanotubes (MWCNT) in the lower‐viscosity natural rubber latex. The MWCNT concentration varied from 0.5 to 2.5 wt%, and the coagulated compounds were vulcanized after compounding in a two‐roll mill. Nanocomposite's swelling behavior was determined by Flory–Rehner crosslink density and Kraus theory, indicating better dispersion in probe sonication, which also was conducted in lesser time and applied lower energy than bath sonication. This result is evidenced through tensile strength and hardness tests, as the better MWCNT dispersion improved the reinforcement due to greater filler–matrix interaction. The electrical response was obtained by impedance spectroscopy, with higher conductivities also found in tip‐sonicated samples. In addition, cyclic strain fatigue test was realized from 20% to 100% strain during 20,000 cycles with simultaneous impedance measurement, reinforcing the better distribution of MWCNT in the probe‐sonicated nanocomposites with higher tensile stress (Payne's effect) and conductivity retention than bath sonicated.
- 10 March 2022
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 139 (23)
Improving the swelling, mechanical, and electrical properties in natural rubber latex/carbon nanotubes nanocomposites: Effect of the sonication method
Conductive polymeric composites are exciting for future electronic applications given the possibility to ally electrical conductivity and flexibility. However, the high viscosity of plasticized elastomers difficult the dispersion of conductive fillers in an elastomeric matrix is difficult. This research aimed to compare the use of bath or probe sonication to disperse multi‐walled carbon nanotubes (MWCNT) in the lower‐viscosity natural rubber latex. The MWCNT concentration varied from 0.5 to 2.5 wt%, and the coagulated compounds were vulcanized after compounding in a two‐roll mill. Nanocomposite's swelling behavior was determined by Flory–Rehner crosslink density and Kraus theory, indicating better dispersion in probe sonication, which also was conducted in lesser time and applied lower energy than bath sonication. This result is evidenced through tensile strength and hardness tests, as the better MWCNT dispersion improved the reinforcement due to greater filler–matrix interaction. The electrical response was obtained by impedance spectroscopy, with higher conductivities also found in tip‐sonicated samples. In addition, cyclic strain fatigue test was realized from 20% to 100% strain during 20,000 cycles with simultaneous impedance measurement, reinforcing the better distribution of MWCNT in the probe‐sonicated nanocomposites with higher tensile stress (Payne's effect) and conductivity retention than bath sonicated.
- Open Access
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 24 (suppl 2)
Electromechanical Evaluation of Ionomeric Polymer-Metal Composites Using Video Analysis
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Materials Research
- Vol. 24 (suppl 2)
Open AccessElectromechanical Evaluation of Ionomeric Polymer-Metal Composites Using Video Analysis
- 16 December 2020
- Published by Wiley in Macromolecular Symposia
- Vol. 394 (1)
Flexible, High‐Density and Water‐Resistant Polypropylene/Thermoplastic Elastomer/Inorganic Fillers Composites
This work is aimed at preparing composites from polypropylene (PP) and ethylene‐octene copolymer (thermoplastic elastomer ‐ TPE) blends with different fillers (talc, mica, and barium sulfate). Characterizations of ash content, melt flow index, density, flexural and tensile properties, impact resistance, hardness, moisture content, and water absorption are realized. The development of these composites intent to obtain materials with higher density and flexibility than PP, pursuing applications in outdoor, high humidity, or immersion in fluids. Interesting results are obtained, mainly with the use of barium sulfate, which increased the density of PP by 45% with the addition of 12 vol.%. Besides the fillers, the addition of TPE is effective in reducing the stiffness and improving the impact toughness, making possible the filler addition without flexibility losses. In this case, the barium sulfate composites showed flexural modulus close to PP/TPE modulus and impact strength superior to pure PP and PP/TPE blend. The composites moisture content and water absorption also show better results from barium sulfate samples, indicating this filler as a great component to composites that pursues high density, flexibility maintenance, and capable to work in the presence of water.
- 16 December 2020
- Published by Wiley in Macromolecular Symposia
- Vol. 394 (1)
Flexible, High‐Density and Water‐Resistant Polypropylene/Thermoplastic Elastomer/Inorganic Fillers Composites
This work is aimed at preparing composites from polypropylene (PP) and ethylene‐octene copolymer (thermoplastic elastomer ‐ TPE) blends with different fillers (talc, mica, and barium sulfate). Characterizations of ash content, melt flow index, density, flexural and tensile properties, impact resistance, hardness, moisture content, and water absorption are realized. The development of these composites intent to obtain materials with higher density and flexibility than PP, pursuing applications in outdoor, high humidity, or immersion in fluids. Interesting results are obtained, mainly with the use of barium sulfate, which increased the density of PP by 45% with the addition of 12 vol.%. Besides the fillers, the addition of TPE is effective in reducing the stiffness and improving the impact toughness, making possible the filler addition without flexibility losses. In this case, the barium sulfate composites showed flexural modulus close to PP/TPE modulus and impact strength superior to pure PP and PP/TPE blend. The composites moisture content and water absorption also show better results from barium sulfate samples, indicating this filler as a great component to composites that pursues high density, flexibility maintenance, and capable to work in the presence of water.
- 24 October 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 138 (14)
Rheological study of EPDM/silicone rubber blends phase inversion and characterization of resultant mechanical and thermal properties
This study was committed to the characterization of the rheological, thermal, mechanical, and morphological properties of ethylene‐propylene‐diene monomer (EPDM)/silicone rubber (SR) blends. These blends are a potential new class of materials for the insulation of circuits and electrical components that actuate in environments with high heat generation. The blends were produced in a torque rheometer with a Banbury type rotor, varying the concentration of EPDM and SR. Results obtained by capillary rheometry were applied to three theoretical models to analyze the phase inversion threshold, which was confirmed by scanning electron microscopy images. Such analyzes were important to describe the consequence of phase inversion on the evaluated properties. It was reported that the increase in SR concentration decreased the elastic modulus and increased the tensile strength of the blends. For blends with composition situated after phase inversion, the SR becomes the matrix, leading to a significant rise in the Vicat softening temperature and reduced thermal conductivity. Such improvements extend the range of applications of these materials as electrical insulators in environments with higher heat generation.
- 24 October 2020
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 138 (14)
Rheological study of EPDM/silicone rubber blends phase inversion and characterization of resultant mechanical and thermal properties
This study was committed to the characterization of the rheological, thermal, mechanical, and morphological properties of ethylene‐propylene‐diene monomer (EPDM)/silicone rubber (SR) blends. These blends are a potential new class of materials for the insulation of circuits and electrical components that actuate in environments with high heat generation. The blends were produced in a torque rheometer with a Banbury type rotor, varying the concentration of EPDM and SR. Results obtained by capillary rheometry were applied to three theoretical models to analyze the phase inversion threshold, which was confirmed by scanning electron microscopy images. Such analyzes were important to describe the consequence of phase inversion on the evaluated properties. It was reported that the increase in SR concentration decreased the elastic modulus and increased the tensile strength of the blends. For blends with composition situated after phase inversion, the SR becomes the matrix, leading to a significant rise in the Vicat softening temperature and reduced thermal conductivity. Such improvements extend the range of applications of these materials as electrical insulators in environments with higher heat generation.