Tetsufumi Tanamoto
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Tetsufumi Tanamoto has a total of 79 co-authors. Here are the top co-authors by number of shared publications:
Keiji Ono
Advanced device laboratory RIKEN Wako-shi 351-0198 Saitama Japan
8 shared publicationsShinobu Fujita
Corporate R&D Center, Toshiba Corporation, Kawasaki, Japan
8 shared publications- Keiji Ono
Advanced device laboratory, RIKEN, Wako-shi, Saitama, Japan
6 shared publications Satoshi Takaya
Corporate R and D Center, Toshiba Corporation
4 shared publicationsTakao Marukame
Toshiba Corporation
3 shared publicationsChika Tanaka
Memory Division, Kioxia Corporation
2 shared publications
Latest Publications
- Open Access
- 25 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 47525-47537
Device/Circuit Simulations of Silicon Spin Qubits Based on a Gate-All-Around Transistor
We theoretically investigated the readout process of a spin–qubit structure based on a gate-all-around (GAA) transistor. Our study focuses on a logical qubit composed of two physical qubits. Different spin configurations result in different charge distributions, which subsequently influence the electrostatic effects on the GAA transistor. Consequently, the current flowing through the GAA transistor depends on the qubit’s state. We calculated the current-voltage characteristics of the three-dimensional configurations of the qubit and GAA structures, using technology computer-aided design (TCAD) simulations. Moreover, we performed circuit simulations using the Simulation Program with Integrated Circuit Emphasis (SPICE) to investigate whether a readout circuit made from complementary metal–oxide semiconductor (CMOS) transistors can amplify the weak signals generated by the qubits. Our findings indicate that, by dynamically controlling the applied voltage within a properly designed circuit, the readout can be detected effectively based on a conventional sense amplifier.
- 25 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 47525-47537
Open AccessDevice/Circuit Simulations of Silicon Spin Qubits Based on a Gate-All-Around Transistor
We theoretically investigated the readout process of a spin–qubit structure based on a gate-all-around (GAA) transistor. Our study focuses on a logical qubit composed of two physical qubits. Different spin configurations result in different charge distributions, which subsequently influence the electrostatic effects on the GAA transistor. Consequently, the current flowing through the GAA transistor depends on the qubit’s state. We calculated the current-voltage characteristics of the three-dimensional configurations of the qubit and GAA structures, using technology computer-aided design (TCAD) simulations. Moreover, we performed circuit simulations using the Simulation Program with Integrated Circuit Emphasis (SPICE) to investigate whether a readout circuit made from complementary metal–oxide semiconductor (CMOS) transistors can amplify the weak signals generated by the qubits. Our findings indicate that, by dynamically controlling the applied voltage within a properly designed circuit, the readout can be detected effectively based on a conventional sense amplifier.
- Open Access
Device/circuit simulations of silicon spin qubits based on a gate-all-around transistor
We theoretically investigated the readout process of a spin--qubit structure based on a gate-all-around (GAA) transistor. Our study focuses on a logical qubit composed of two physical qubits. Different spin configurations result in different charge distributions, which subsequently influence the electrostatic effects on the GAA transistor. Consequently, the current flowing through the GAA transistor depends on the qubit's state. We calculated the current-voltage characteristics of the three-dimensional configurations of the qubit and GAA structures, using technology computer-aided design (TCAD) simulations. Moreover, we performed circuit simulations using the Simulation Program with Integrated Circuit Emphasis (SPICE) to investigate whether a readout circuit made from complementary metal--oxide semiconductor (CMOS) transistors can amplify the weak signals generated by the qubits. Our findings indicate that, by dynamically controlling the applied voltage within a properly designed circuit, the readout can be detected effectively based on a conventional sense amplifier.
Open AccessDevice/circuit simulations of silicon spin qubits based on a gate-all-around transistor
We theoretically investigated the readout process of a spin--qubit structure based on a gate-all-around (GAA) transistor. Our study focuses on a logical qubit composed of two physical qubits. Different spin configurations result in different charge distributions, which subsequently influence the electrostatic effects on the GAA transistor. Consequently, the current flowing through the GAA transistor depends on the qubit's state. We calculated the current-voltage characteristics of the three-dimensional configurations of the qubit and GAA structures, using technology computer-aided design (TCAD) simulations. Moreover, we performed circuit simulations using the Simulation Program with Integrated Circuit Emphasis (SPICE) to investigate whether a readout circuit made from complementary metal--oxide semiconductor (CMOS) transistors can amplify the weak signals generated by the qubits. Our findings indicate that, by dynamically controlling the applied voltage within a properly designed circuit, the readout can be detected effectively based on a conventional sense amplifier.
- Open Access
- 21 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72  (9) , 4642-4647
Indexing Current–Voltage Characteristics Using a Hash Function
Effectively managing a large number of devices is crucial for enhancing the reliability of target devices. Moreover, it is important to differentiate between devices of the same structure in order to achieve the optimal performance. However, identifying subtle differences can be challenging, particularly when the devices share similar characteristics, such as transistors on a wafer. To address this issue, we propose an indexing method for current–voltage (I–V) characteristics that assigns proximity numbers to similar devices. Specifically, we demonstrate the application of the locality-sensitive hashing (LSH) algorithm to Coulomb blockade phenomena observed in pMOSFETs and nanowire transistors. In this approach, lengthy data on current characteristics are replaced with hash IDs, facilitating the identification of individual devices and streamlining the management of a large number of devices.
- 21 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72  (9) , 4642-4647
Open AccessIndexing Current–Voltage Characteristics Using a Hash Function
Effectively managing a large number of devices is crucial for enhancing the reliability of target devices. Moreover, it is important to differentiate between devices of the same structure in order to achieve the optimal performance. However, identifying subtle differences can be challenging, particularly when the devices share similar characteristics, such as transistors on a wafer. To address this issue, we propose an indexing method for current–voltage (I–V) characteristics that assigns proximity numbers to similar devices. Specifically, we demonstrate the application of the locality-sensitive hashing (LSH) algorithm to Coulomb blockade phenomena observed in pMOSFETs and nanowire transistors. In this approach, lengthy data on current characteristics are replaced with hash IDs, facilitating the identification of individual devices and streamlining the management of a large number of devices.
- Open Access
- 25 April 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137  (16)
Effects of valley splitting on resonant-tunneling readout of spin qubits
The effect of valley splitting on the readout of qubit states is theoretically investigated in a three-quantum-dot (QD) system. A single unit of the three-QD system consists of qubit-QDs and a channel-QD that is connected to a conventional transistor. The nonlinear source–drain current characteristics under resonant-tunneling effects are used to distinguish different qubit states. Using nonequilibrium Green functions, the current formula for the three-QD system is derived when each QD has two valley energy levels. Two valley states in each QD are considered to be affected by variations in the fabrication process. We found that when valley splitting is smaller than Zeeman splitting, the current nonlinearity can improve the readout, provided that the nonuniformity of the valley energy levels is small. Conversely, when the valley splitting is larger than the Zeeman splitting, the nonuniformity degraded the readout. In both cases, we showed that there are regions where the measurement time tmeas is much less than the decoherence time tdec such that tdec/tmeas>100. This suggests that less than 1% measurement error is anticipated, which opens up the possibility of implementing surface codes even in the presence of valley splitting.
- 25 April 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137  (16)
Open AccessEffects of valley splitting on resonant-tunneling readout of spin qubits
The effect of valley splitting on the readout of qubit states is theoretically investigated in a three-quantum-dot (QD) system. A single unit of the three-QD system consists of qubit-QDs and a channel-QD that is connected to a conventional transistor. The nonlinear source–drain current characteristics under resonant-tunneling effects are used to distinguish different qubit states. Using nonequilibrium Green functions, the current formula for the three-QD system is derived when each QD has two valley energy levels. Two valley states in each QD are considered to be affected by variations in the fabrication process. We found that when valley splitting is smaller than Zeeman splitting, the current nonlinearity can improve the readout, provided that the nonuniformity of the valley energy levels is small. Conversely, when the valley splitting is larger than the Zeeman splitting, the nonuniformity degraded the readout. In both cases, we showed that there are regions where the measurement time tmeas is much less than the decoherence time tdec such that tdec/tmeas>100. This suggests that less than 1% measurement error is anticipated, which opens up the possibility of implementing surface codes even in the presence of valley splitting.
- Open Access
- 1 April 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64  (4) , 04SP08
Effects of dissipation in reservoir computing using spin qubit array
Reservoir computing (RC) is one of the hottest topics as a promising application for many physical devices because their device characteristics can be directly used in computing sequences. Quantum RC is also a promising candidate for the application of even small-number qubit systems. Here, we propose a quantum RC based on the spin qubit system reflecting the status of the spin qubits in experiments of a one-dimensional qubit array. Spin qubits are coupled via the Heisenberg interaction, and data sequences are inputted to one of the spin qubits by pulsed rotations. By introducing dissipation, we obtain satisfactory performance as a quantum RC.
- 1 April 2025
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 64  (4) , 04SP08
Open AccessEffects of dissipation in reservoir computing using spin qubit array
Reservoir computing (RC) is one of the hottest topics as a promising application for many physical devices because their device characteristics can be directly used in computing sequences. Quantum RC is also a promising candidate for the application of even small-number qubit systems. Here, we propose a quantum RC based on the spin qubit system reflecting the status of the spin qubits in experiments of a one-dimensional qubit array. Spin qubits are coupled via the Heisenberg interaction, and data sequences are inputted to one of the spin qubits by pulsed rotations. By introducing dissipation, we obtain satisfactory performance as a quantum RC.
- Open Access
Effects of valley splitting on resonant-tunneling readout of spin qubits
The effect of valley splitting on the readout of qubit states is theoretically investigated in a three-quantum-dot (QD) system. A single unit of the three-QD system consists of qubit-QDs and a channel-QD that is connected to a conventional transistor. The nonlinear source--drain current characteristics under resonant-tunneling effects are used to distinguish different qubit states. Using nonequilibrium Green functions, the current formula for the three-QD system is derived when each QD has two valley energy levels. Two valley states in each QD are considered to be affected by variations in the fabrication process. We found that when valley splitting is smaller than Zeeman splitting, the current nonlinearity can improve the readout, provided that the nonuniformity of the valley energy levels is small. Conversely, when the valley splitting is larger than the Zeeman splitting, the nonuniformity degraded the readout. In both cases, we showed that there are regions where the measurement time $t_{\rm meas}$ is much less than the decoherence time $t_{\rm dec}$ such that $t_{\rm dec}/t_{\rm meas}>100$. This suggests that less than 1\% measurement error is anticipated, which opens up the possibility for implementing surface codes even in the presence of valley splitting.Open AccessEffects of valley splitting on resonant-tunneling readout of spin qubits
The effect of valley splitting on the readout of qubit states is theoretically investigated in a three-quantum-dot (QD) system. A single unit of the three-QD system consists of qubit-QDs and a channel-QD that is connected to a conventional transistor. The nonlinear source--drain current characteristics under resonant-tunneling effects are used to distinguish different qubit states. Using nonequilibrium Green functions, the current formula for the three-QD system is derived when each QD has two valley energy levels. Two valley states in each QD are considered to be affected by variations in the fabrication process. We found that when valley splitting is smaller than Zeeman splitting, the current nonlinearity can improve the readout, provided that the nonuniformity of the valley energy levels is small. Conversely, when the valley splitting is larger than the Zeeman splitting, the nonuniformity degraded the readout. In both cases, we showed that there are regions where the measurement time $t_{\rm meas}$ is much less than the decoherence time $t_{\rm dec}$ such that $t_{\rm dec}/t_{\rm meas}>100$. This suggests that less than 1\% measurement error is anticipated, which opens up the possibility for implementing surface codes even in the presence of valley splitting. - Open Access
- 1 March 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63  (3) , 03SP69
Noise properties in the Coulomb blockade region of FinFETs
Fin FETs (FinFETs) are a promising candidate for the platform of Si quantum computers. The noise properties of commercial FinFETs were experimentally investigated at temperatures below 10 K. The drain current showed Coulomb oscillation, indicating that the FinFET channel became a single quantum dot. Moreover, the noise in the drain current was analyzed, and the basic properties of commercial FinFETs in the low-temperature region were discussed.
- 1 March 2024
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 63  (3) , 03SP69
Open AccessNoise properties in the Coulomb blockade region of FinFETs
Fin FETs (FinFETs) are a promising candidate for the platform of Si quantum computers. The noise properties of commercial FinFETs were experimentally investigated at temperatures below 10 K. The drain current showed Coulomb oscillation, indicating that the FinFET channel became a single quantum dot. Moreover, the noise in the drain current was analyzed, and the basic properties of commercial FinFETs in the low-temperature region were discussed.
- Open Access
- 4 December 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134  (21)
Readout using resonant tunneling in silicon spin qubits
Spin qubit systems are one of the promising candidates for quantum computing. The quantum dot (QD) arrays are intensively investigated by many researchers. Because the energy-difference between the up-spin and down-spin states is very small, the detection of the qubit state is of prime importance in this field. Moreover, many wires are required to control qubit systems. Therefore, the integration of qubits and wires is also an important issue. In this study, the measurement process of QD arrays is theoretically investigated using resonant tunneling, controlled by a conventional transistor. It is shown that the number of possible measurements during coherence time can exceed a hundred under the backaction of the measurements owing to the nonlinear characteristics of resonant tunneling. It is also discussed to read out the measurement results by the conventional transistor.
- 4 December 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 134  (21)
Open AccessReadout using resonant tunneling in silicon spin qubits
Spin qubit systems are one of the promising candidates for quantum computing. The quantum dot (QD) arrays are intensively investigated by many researchers. Because the energy-difference between the up-spin and down-spin states is very small, the detection of the qubit state is of prime importance in this field. Moreover, many wires are required to control qubit systems. Therefore, the integration of qubits and wires is also an important issue. In this study, the measurement process of QD arrays is theoretically investigated using resonant tunneling, controlled by a conventional transistor. It is shown that the number of possible measurements during coherence time can exceed a hundred under the backaction of the measurements owing to the nonlinear characteristics of resonant tunneling. It is also discussed to read out the measurement results by the conventional transistor.
- 7 September 2023
- Published by Japan Society of Applied Physics
Noise properties in the Coulomb blockade region of FinFET
2023 International Conference on Solid State Devices and Materials ,Noise properties in the Coulomb blockade region of FinFET
- 7 September 2023
- Published by Japan Society of Applied Physics
Noise properties in the Coulomb blockade region of FinFET
2023 International Conference on Solid State Devices and Materials ,Noise properties in the Coulomb blockade region of FinFET