Gustavo Adrian Torchia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gustavo Adrian Torchia has a total of 201 co-authors. Here are the top co-authors by number of shared publications:
L. Roso
Centro de Láseres Pulsados (CLPU), Parque Científico, E-37185 Villamayor, Salamanca, Spain
23 shared publications- Daniel Jaque
Universidad Autónoma de Madrid
19 shared publications - Airán Ródenas
Departamento de Física, Universidad de La Laguna, Apdo. 456, E-38200 San Cristóbal de La Laguna, Spain
15 shared publications - Eugenio Cantelar
Departamento de Física de Materiales, Facultad de Ciencias, Universidad Autónoma de Madrid, Madrid, Spain
14 shared publications - Javier Rodriguez Vazquez de Aldana
Aplicaciones del Láser y Fotónica (ALF-USAL), University of Salamanca, 37008 Salamanca, Spain
14 shared publications F. Jaque
Departamento de Física de Materiales, Facultad de Ciencias, Universidad Autónoma de Madrid,Madrid 28049, Spain
10 shared publications
Latest Publications
- 13 August 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (24) , 8243-8252
Low-cost, combined M-line and reflectivity approach for prism-coupled thin-film characterization
While prism coupling is a well-established technique for thin-film characterization, detailed and practical implementation guides for resource-limited settings are scarce, hindering reproducibility. This work addresses this gap by presenting a low-cost, integrated system that combines M-line spectroscopy and angular reflectivity measurements within a single optical setup, enabling mutual validation of results. We provide a comprehensive guide covering the experimental design, alignment procedures, and data analysis, including solutions for common challenges like beam displacement compensation. The methodology is supported by open-source Python tools for multilayer modeling and parameter reconstruction, laying the groundwork for future automation. The system’s efficacy is demonstrated on spin-coated amorphous polymer films, achieving a refractive index accuracy of ±0.004 and a thickness precision of ±0.04µm. By using low-cost components, our system could achieve experimental performance comparable to that of expensive commercial setups through the incorporation of a mechanical reduction system capable of achieving an angular resolution better than ±0.001. By bridging the gap between theory and hands-on experimentation, this paper serves as a practical resource for small laboratories and educational projects, making reliable optical characterization accessible for applications in photonics, sensing, and materials science.
- 13 August 2026
- Published by Optica Publishing Group in Applied Optics
- Vol. 65 (24) , 8243-8252
Low-cost, combined M-line and reflectivity approach for prism-coupled thin-film characterization
While prism coupling is a well-established technique for thin-film characterization, detailed and practical implementation guides for resource-limited settings are scarce, hindering reproducibility. This work addresses this gap by presenting a low-cost, integrated system that combines M-line spectroscopy and angular reflectivity measurements within a single optical setup, enabling mutual validation of results. We provide a comprehensive guide covering the experimental design, alignment procedures, and data analysis, including solutions for common challenges like beam displacement compensation. The methodology is supported by open-source Python tools for multilayer modeling and parameter reconstruction, laying the groundwork for future automation. The system’s efficacy is demonstrated on spin-coated amorphous polymer films, achieving a refractive index accuracy of ±0.004 and a thickness precision of ±0.04µm. By using low-cost components, our system could achieve experimental performance comparable to that of expensive commercial setups through the incorporation of a mechanical reduction system capable of achieving an angular resolution better than ±0.001. By bridging the gap between theory and hands-on experimentation, this paper serves as a practical resource for small laboratories and educational projects, making reliable optical characterization accessible for applications in photonics, sensing, and materials science.
- 12 February 2025
- Published by Optica Publishing Group in Applied Optics
- Vol. 64 (6) , 1427-1434
Design, fabrication, testing, and packaging of the 1 × 8 power splitter developed under the SOI platform
This paper presents a brief roadmap to design and fabricate a final device corresponding to a 1×8 power splitter developed under the silicon-on-insulator (SOI) platform. To describe the entire technological process for the power splitter, first, we begin by designing and validating our proposed photonic circuit through calculations using several computational routines supported by popular numerical methods, such as the finite-difference time-domain (FDTD) and beam propagation methods (BPM). In the second step, the technological platform employed for fabricating the designed optical circuit is briefly described. Subsequently, the primary objective of this paper is presented, which is to provide a detailed introduction and explanation of the assembly process, including the positioning and coupling of the optical signal to the chip and the integration of all components. Additionally, we developed the packaging process, designing the case to include internal pieces and the external housing suitable for the final system, including fiber optics input/output interfaces. In this final step, all internal and cover components for the packaging were fabricated using 3D printing.
- 12 February 2025
- Published by Optica Publishing Group in Applied Optics
- Vol. 64 (6) , 1427-1434
Design, fabrication, testing, and packaging of the 1 × 8 power splitter developed under the SOI platform
This paper presents a brief roadmap to design and fabricate a final device corresponding to a 1×8 power splitter developed under the silicon-on-insulator (SOI) platform. To describe the entire technological process for the power splitter, first, we begin by designing and validating our proposed photonic circuit through calculations using several computational routines supported by popular numerical methods, such as the finite-difference time-domain (FDTD) and beam propagation methods (BPM). In the second step, the technological platform employed for fabricating the designed optical circuit is briefly described. Subsequently, the primary objective of this paper is presented, which is to provide a detailed introduction and explanation of the assembly process, including the positioning and coupling of the optical signal to the chip and the integration of all components. Additionally, we developed the packaging process, designing the case to include internal pieces and the external housing suitable for the final system, including fiber optics input/output interfaces. In this final step, all internal and cover components for the packaging were fabricated using 3D printing.
- 1 January 2025
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 64 (01) , 017104-13
Small multimode interferometer with simplified coherent coupling branches used to develop a lower footprint power splitter on silicon-on-insulator platform
We introduced a innovative approach to fabricating a 1×2 power splitter under the silicon-on-insulator (SOI) platform, which can be scaled to a 1×N system device. The current design strategy is based on the well-known simplified coherent coupling, which allows for the construction of sharp bends. To split the incoming light, a small multimode interferometer (MMI) is added at the entrance of the splitter. Analysis and discussion regarding the sensitivity of the design parameters will be expanded throughout the paper. In addition, the proposed splitter architecture was fabricated and evaluated in 1×2 and 1×4 versions, and these devices were compared with splitters based on standard MMI also performed on the same SOI photonic chip. The splitter scheme demonstrates similar performance to standard MMI; however, a slight spectral flat response was observed in the new devices ensuring reliable operation across various wavelengths. This presented approach enables the design of highly compact devices, potentially opening different avenues to improve and enhance the performance of integrated devices developed under the SOI scheme.
- 1 January 2025
- Published by SPIE-Intl Soc Optical Eng in Optical Engineering
- Vol. 64 (01) , 017104-13
Small multimode interferometer with simplified coherent coupling branches used to develop a lower footprint power splitter on silicon-on-insulator platform
We introduced a innovative approach to fabricating a 1×2 power splitter under the silicon-on-insulator (SOI) platform, which can be scaled to a 1×N system device. The current design strategy is based on the well-known simplified coherent coupling, which allows for the construction of sharp bends. To split the incoming light, a small multimode interferometer (MMI) is added at the entrance of the splitter. Analysis and discussion regarding the sensitivity of the design parameters will be expanded throughout the paper. In addition, the proposed splitter architecture was fabricated and evaluated in 1×2 and 1×4 versions, and these devices were compared with splitters based on standard MMI also performed on the same SOI photonic chip. The splitter scheme demonstrates similar performance to standard MMI; however, a slight spectral flat response was observed in the new devices ensuring reliable operation across various wavelengths. This presented approach enables the design of highly compact devices, potentially opening different avenues to improve and enhance the performance of integrated devices developed under the SOI scheme.
- Open Access
Small MMI with simplified coherent coupling branches used to develop a lower footprint power splitter on SOI platform
In this paper, we introduce a new approach to fabricate under the Silicon on Insulator (SOI) platform a 1x2 power splitter and scale it to 1xN system device from the proposed model. The current strategy of design is based on the well-known simplified coherent coupling (SCC) which allows the construction of very sharp bends. To split the incoming light, we add at the entrance of the splitter a small Multi Mode Interferometer (MMI). The sensibility of the design parameters is analyzed and discussed in the paper. In addition, we fabricated and evaluated the new splitter architecture on 1x2 and 1x4 versions and then compared our devices with those splitters based on standard multimode interferometer (MMI) also performed in the same SOI photonic chip. The new splitter scheme shows a similar performance to standard MMI, however, a slight spectral flat response was observed in new devices. By the novel approach, highly compact devices can be designed so this strategy can also open new avenues to improve and enhance the performance of integrated devices developed under the SOI scheme.
Open AccessSmall MMI with simplified coherent coupling branches used to develop a lower footprint power splitter on SOI platform
In this paper, we introduce a new approach to fabricate under the Silicon on Insulator (SOI) platform a 1x2 power splitter and scale it to 1xN system device from the proposed model. The current strategy of design is based on the well-known simplified coherent coupling (SCC) which allows the construction of very sharp bends. To split the incoming light, we add at the entrance of the splitter a small Multi Mode Interferometer (MMI). The sensibility of the design parameters is analyzed and discussed in the paper. In addition, we fabricated and evaluated the new splitter architecture on 1x2 and 1x4 versions and then compared our devices with those splitters based on standard multimode interferometer (MMI) also performed in the same SOI photonic chip. The new splitter scheme shows a similar performance to standard MMI, however, a slight spectral flat response was observed in new devices. By the novel approach, highly compact devices can be designed so this strategy can also open new avenues to improve and enhance the performance of integrated devices developed under the SOI scheme.
- 30 June 2023
- Published by Sociedad Espanola de Optica in Optica Pura y Aplicada
- Vol. 56 (2)
New organic platform to integrated photonic device fabrication
- 30 June 2023
- Published by Sociedad Espanola de Optica in Optica Pura y Aplicada
- Vol. 56 (2)
New organic platform to integrated photonic device fabrication
- 8 March 2022
- Published by IOP Publishing in Journal of Optics
- Vol. 24 (4) , 045504
Simple interferometric setup enabling sub-Fourier-scale ultra-short laser pulses
In this work, we describe an interferometric method to generate ultra-short pulses below the Fourier limit. It is done by extending concepts first developed in the spatial domain to achieve sub-diffractive beams through the addition of a spatial chirp in one of the arms of a Michelson interferometer using a spherical mirror. To experimentally synthesize sub-Fourier pulses, we replace the spherical mirror with a water cell, since it produces chirp in the temporal domain. We also present an alternative procedure, based on asymmetrical interference between the widened pulse and the original pulse where the peaks of both pulses exhibit a temporal delay achieving the narrowing of ultra-short pulses with sub-Fourier scales. To characterize the performance of the system, we performed a preliminary assessment considering the percentage of full width at half-maximum shrinking obtained for each scheme. By means of a symmetrical configuration, 7% and 12% pulse reductions were verified, both experimentally and analytically, while for the non-symmetrical configuration, 10% and 24% reductions were achieved corresponding to main lobe to side-lobe ratios of 10% and 30%. The experimental setup scheme is simple, versatile and able to work with high-power laser sources and ultra-short pulses with a broad bandwidth at any central wavelength. The results presented in this work are promising and help to enlighten new routes and strategies in the design of coherent control systems. We envision that they will become broadly useful in different areas from strong field domain to quantum information.
- 8 March 2022
- Published by IOP Publishing in Journal of Optics
- Vol. 24 (4) , 045504
Simple interferometric setup enabling sub-Fourier-scale ultra-short laser pulses
In this work, we describe an interferometric method to generate ultra-short pulses below the Fourier limit. It is done by extending concepts first developed in the spatial domain to achieve sub-diffractive beams through the addition of a spatial chirp in one of the arms of a Michelson interferometer using a spherical mirror. To experimentally synthesize sub-Fourier pulses, we replace the spherical mirror with a water cell, since it produces chirp in the temporal domain. We also present an alternative procedure, based on asymmetrical interference between the widened pulse and the original pulse where the peaks of both pulses exhibit a temporal delay achieving the narrowing of ultra-short pulses with sub-Fourier scales. To characterize the performance of the system, we performed a preliminary assessment considering the percentage of full width at half-maximum shrinking obtained for each scheme. By means of a symmetrical configuration, 7% and 12% pulse reductions were verified, both experimentally and analytically, while for the non-symmetrical configuration, 10% and 24% reductions were achieved corresponding to main lobe to side-lobe ratios of 10% and 30%. The experimental setup scheme is simple, versatile and able to work with high-power laser sources and ultra-short pulses with a broad bandwidth at any central wavelength. The results presented in this work are promising and help to enlighten new routes and strategies in the design of coherent control systems. We envision that they will become broadly useful in different areas from strong field domain to quantum information.
- 17 January 2022
- Published by Elsevier in Optics & Laser Technology
- Vol. 149, 107871
Significant improvement in optical propagation of lithium niobate written waveguides by a thermal annealing
- 17 January 2022
- Published by Elsevier in Optics & Laser Technology
- Vol. 149, 107871
Significant improvement in optical propagation of lithium niobate written waveguides by a thermal annealing
- Open Access
- 23 September 2021
- Published by Optica Publishing Group in Optics Letters
- Vol. 46 (19) , 4761-4764
Effective super-bandwidth in laser pulses
We present here a theoretical analysis of the interaction between an ideal two-level quantum system and a super-oscillatory pulse, like the one proposed and successfully synthesized in [J. Opt.23, 075604 (2021)JOOPDB0150-536X10.1088/2040-8986/abfedf; arXiv:2106.09192 (2021)]. As a prominent feature, these pulses present a high efficiency of the central super-oscillatory region in relation to unavoidable sidelobes. Our study shows an increase in the effective bandwidth of the pulse in the super-oscillatory region, and not only the appearance of a local frequency higher than its highest Fourier-frequency component, as in the usual description of the phenomenon of super-oscillations. Beyond introducing the concept of effective super-bandwidth, the presented results could be relevant for experimental applications and opening new perspectives for laser-matter interaction.
- 23 September 2021
- Published by Optica Publishing Group in Optics Letters
- Vol. 46 (19) , 4761-4764
Open AccessEffective super-bandwidth in laser pulses
We present here a theoretical analysis of the interaction between an ideal two-level quantum system and a super-oscillatory pulse, like the one proposed and successfully synthesized in [J. Opt.23, 075604 (2021)JOOPDB0150-536X10.1088/2040-8986/abfedf; arXiv:2106.09192 (2021)]. As a prominent feature, these pulses present a high efficiency of the central super-oscillatory region in relation to unavoidable sidelobes. Our study shows an increase in the effective bandwidth of the pulse in the super-oscillatory region, and not only the appearance of a local frequency higher than its highest Fourier-frequency component, as in the usual description of the phenomenon of super-oscillations. Beyond introducing the concept of effective super-bandwidth, the presented results could be relevant for experimental applications and opening new perspectives for laser-matter interaction.
- Open Access
- 1 June 2020
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 14 (3) , 104-108
Design conditions in the middle range for implementation of integrated ring resonators in LiNbO 3 by direct laser writing
The aim of this work is to design an integrated optical ring resonator to be implemented in LiNbO 3 with a 2.5 mm radius and an operating wavelength of 1550 nm. Considering these ring parameters, a free spectral range of 71.54 pm and a quality factor of ∼ were calculated. The authors apply results to improve the implementation of femtosecond laser writing in lithium niobate crystals. As it is well‐known finite difference time domain method requires large memory and time for processing circuits with large footprint (few square mm), in contrast, the beam propagation method allows to simulate large bends in a simple way. RSoft suite design tools commonly represent circles by closed polygons whose geometrical parameters are not optimised to obtain bending losses as least as possible, as suggested by coherent coupling theory. In this sense, the suitable determination of a splice angle (in this case ), shape and length for segments are key parameters in the ring design. For this purpose, an ad hoc software was implemented to overcome this drawback. In summary, a 250 sided polygon side showed a suitable coupling performance and established a new layout approach for middle range rings.
- 1 June 2020
- Published by Institution of Engineering and Technology (IET) in IET Optoelectronics
- Vol. 14 (3) , 104-108
Open AccessDesign conditions in the middle range for implementation of integrated ring resonators in LiNbO 3 by direct laser writing
The aim of this work is to design an integrated optical ring resonator to be implemented in LiNbO 3 with a 2.5 mm radius and an operating wavelength of 1550 nm. Considering these ring parameters, a free spectral range of 71.54 pm and a quality factor of ∼ were calculated. The authors apply results to improve the implementation of femtosecond laser writing in lithium niobate crystals. As it is well‐known finite difference time domain method requires large memory and time for processing circuits with large footprint (few square mm), in contrast, the beam propagation method allows to simulate large bends in a simple way. RSoft suite design tools commonly represent circles by closed polygons whose geometrical parameters are not optimised to obtain bending losses as least as possible, as suggested by coherent coupling theory. In this sense, the suitable determination of a splice angle (in this case ), shape and length for segments are key parameters in the ring design. For this purpose, an ad hoc software was implemented to overcome this drawback. In summary, a 250 sided polygon side showed a suitable coupling performance and established a new layout approach for middle range rings.
- 27 February 2020
- Published by IOP Publishing in Journal of Physics B: Atomic, Molecular and Optical Physics
- Vol. 53 (6) , 065403
Above-threshold ionization driven by few-cycle spatially bounded inhomogeneous laser fields
In this work, we study the main features of the photoelectrons generated when noble gas atoms are driven by spatially bounded inhomogeneous strong laser fields. These spatial inhomogeneous oscillating fields, employed to ionize and accelerate the electrons, result from the interaction between a pulsed low intensity laser and bow-tie shaped gold nanostructures. Under this excitation scheme, energy-resolved above-threshold ionization (ATI) photoelectron spectra have been simulated by solving the one-dimensional (1D) time-dependent Schrödinger equation (TDSE) within the single active electron (SAE) approximation. These quantum mechanical results are supported by their classical counterparts, obtained by the numerical integration of the Newton–Lorentz equation. By using near-infrared wavelengths (0.8–3 μ m) sources, our results show that very high energetic electrons (with kinetic energies in the keV domain) can be generated, far exceeding the limits obtained by using conventional, spatially homogeneous fields. This new characteristic can be supported considering the non-recombining electrons trajectories, already reported by Neyra and coworkers (Neyra E, et al 2018 J. Opt. 20 , 034002). In order to build a real representation of the spatial dependence of the plasmonic-enhanced field in an analytic function, we fit the generated ’actual’ field using two Gaussian functions. We have further analyzed and explored this plasmonic-modified ATI phenomenon in a model argon atom by using several driven wavelengths at intensities in the order of 10 14 W cm −2 . Throughout our contribution we carefully scrutinize the differences between the ATI obtained using spatially homogeneous and inhomogeneous laser fields. We present the various physical origins, or correspondingly distinct physical mechanisms, for the ATI generation driven by spatially bounded inhomogeneous fields.
- 27 February 2020
- Published by IOP Publishing in Journal of Physics B: Atomic, Molecular and Optical Physics
- Vol. 53 (6) , 065403
Above-threshold ionization driven by few-cycle spatially bounded inhomogeneous laser fields
In this work, we study the main features of the photoelectrons generated when noble gas atoms are driven by spatially bounded inhomogeneous strong laser fields. These spatial inhomogeneous oscillating fields, employed to ionize and accelerate the electrons, result from the interaction between a pulsed low intensity laser and bow-tie shaped gold nanostructures. Under this excitation scheme, energy-resolved above-threshold ionization (ATI) photoelectron spectra have been simulated by solving the one-dimensional (1D) time-dependent Schrödinger equation (TDSE) within the single active electron (SAE) approximation. These quantum mechanical results are supported by their classical counterparts, obtained by the numerical integration of the Newton–Lorentz equation. By using near-infrared wavelengths (0.8–3 μ m) sources, our results show that very high energetic electrons (with kinetic energies in the keV domain) can be generated, far exceeding the limits obtained by using conventional, spatially homogeneous fields. This new characteristic can be supported considering the non-recombining electrons trajectories, already reported by Neyra and coworkers (Neyra E, et al 2018 J. Opt. 20 , 034002). In order to build a real representation of the spatial dependence of the plasmonic-enhanced field in an analytic function, we fit the generated ’actual’ field using two Gaussian functions. We have further analyzed and explored this plasmonic-modified ATI phenomenon in a model argon atom by using several driven wavelengths at intensities in the order of 10 14 W cm −2 . Throughout our contribution we carefully scrutinize the differences between the ATI obtained using spatially homogeneous and inhomogeneous laser fields. We present the various physical origins, or correspondingly distinct physical mechanisms, for the ATI generation driven by spatially bounded inhomogeneous fields.