Gorkem Kulah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gorkem Kulah has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Murat Koksal
Department of Mechanical Engineering, Hacettepe University, Ankara, Turkey
14 shared publications - Cihan Ates
Institute of Thermal Turbomachinery, Karlsruhe Institute of Technology (KIT), 76137 Karlsruhe, Germany
10 shared publications - Nevin Selçuk
Department of Chemical Engineering, Middle East Technical University, Ankara, Turkey
10 shared publications Nevin Selçuk
8 shared publicationsGuzide Ozen
Roketsan Inc, Ankara, 06780, Turkey
6 shared publications- Navid Mostoufi
School of Chemical Engineering, College of Engineering, University of Tehran, Tehran, Iran
5 shared publications
Latest Publications
- 14 February 2026
- Published by Springer Nature
- p. 243-253
Eulerian-Eulerian Modelling of Discharge Process in Spouted Bed Solar Receivers
- 14 February 2026
- Published by Springer Nature
- p. 243-253
Eulerian-Eulerian Modelling of Discharge Process in Spouted Bed Solar Receivers
- 14 June 2025
- Published by Elsevier in Particuology
- Vol. 104, 88-102
Coarse grained CFD-DEM simulation of the convective cooling during the discharge process in spouted bed solar receivers
- 14 June 2025
- Published by Elsevier in Particuology
- Vol. 104, 88-102
Coarse grained CFD-DEM simulation of the convective cooling during the discharge process in spouted bed solar receivers
- 14 May 2025
- Published by Elsevier in Particuology
- Vol. 103, 18-28
Experimental investigation of directly irradiated conical spouted bed thermal receivers
- 14 May 2025
- Published by Elsevier in Particuology
- Vol. 103, 18-28
Experimental investigation of directly irradiated conical spouted bed thermal receivers
- 14 October 2023
- Published by Elsevier in Powder Technology
- Vol. 431
Solids dispersion in high density circulating fluidized beds
- 14 October 2023
- Published by Elsevier in Powder Technology
- Vol. 431
Solids dispersion in high density circulating fluidized beds
- 4 February 2022
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 176
Performance and validation of a radiation model coupled with a transient bubbling fluidized bed combustion model
- 4 February 2022
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 176
Performance and validation of a radiation model coupled with a transient bubbling fluidized bed combustion model
- 1 September 2021
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 167
Influence of bag filter ash to spectral thermal radiation in fluidized bed combustors co-fired with biomass
- 1 September 2021
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 167
Influence of bag filter ash to spectral thermal radiation in fluidized bed combustors co-fired with biomass
- 14 January 2021
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 99 (7) , 1607-1615
Gas velocity distribution in conical spouted beds with high‐density particles
Local gas velocity measurements were conducted utilizing a Pitot tube in two small‐scale (Dc = 150 mm, γ = 30°, 60°) and one large‐scale (Dc = 250 mm, γ = 66°) conical spouted beds. Three different types of particles, zirconia (ρp = 6050 kg/m3), zirconia‐toughened alumina (ρp = 3700 kg/m3), and glass beads (ρp = 2460 kg/m3), were used in the experiments. Careful calibration of the Pitot tube for determination of gas velocities in the annulus section was carried out in a separate, loosely packed‐bed set‐up, which represents the flow conditions in the annulus section of the spouted bed. Solids hold‐up profiles were used to calculate the superficial gas velocities and determine the amount of air flowing through the spout, interface, and annulus. Effects of axial position, conical angle, bed size, and particle density on gas velocity profiles were investigated. It is shown that the amount of air flow through the annulus increases as the axial distance and particle density increases; however, it decreases with increasing cone angle. Dispersion of the gas into the annulus is found to be significantly higher in the large‐scale unit than the small‐scale unit.
- 14 January 2021
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 99 (7) , 1607-1615
Gas velocity distribution in conical spouted beds with high‐density particles
Local gas velocity measurements were conducted utilizing a Pitot tube in two small‐scale (Dc = 150 mm, γ = 30°, 60°) and one large‐scale (Dc = 250 mm, γ = 66°) conical spouted beds. Three different types of particles, zirconia (ρp = 6050 kg/m3), zirconia‐toughened alumina (ρp = 3700 kg/m3), and glass beads (ρp = 2460 kg/m3), were used in the experiments. Careful calibration of the Pitot tube for determination of gas velocities in the annulus section was carried out in a separate, loosely packed‐bed set‐up, which represents the flow conditions in the annulus section of the spouted bed. Solids hold‐up profiles were used to calculate the superficial gas velocities and determine the amount of air flowing through the spout, interface, and annulus. Effects of axial position, conical angle, bed size, and particle density on gas velocity profiles were investigated. It is shown that the amount of air flow through the annulus increases as the axial distance and particle density increases; however, it decreases with increasing cone angle. Dispersion of the gas into the annulus is found to be significantly higher in the large‐scale unit than the small‐scale unit.
- 6 October 2020
- Published by Elsevier in Journal of Quantitative Spectroscopy and Radiative Transfer
- Vol. 257, 107370
Performance of banded SLW-1 in presence of non-gray walls and particles in fluidized bed combustors
- 6 October 2020
- Published by Elsevier in Journal of Quantitative Spectroscopy and Radiative Transfer
- Vol. 257, 107370
Performance of banded SLW-1 in presence of non-gray walls and particles in fluidized bed combustors
- 8 November 2019
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 194 (2) , 435-448
Modeling of Fluidized Bed Combustion of Lignite with High Nitrogen Content Cotton Residue
A comprehensive system model, previously developed for prediction of combustion behaviors of Turkish lignites, lignite/hazelnut shell, and lignite/olive residue blends in a 0.3-MWt atmospheric bubbling fluidized bed combustor (ABFBC), is extended for modeling of co-combustion of Turkish lignite and cotton residue. Cotton residue has high nitrogen content (~4.1 wt% ar) unlike lignite (~0.9 wt% ar), olive residue (~1.6 wt% ar), and hazelnut shell (~0.5 wt% ar), which leads to relatively high emissions of nitric oxides (NOx) and nitrous oxide (N2O). For accurate prediction of emissions of NO and N2O, a sufficiently detailed NO and N2O formation and reduction reaction scheme is incorporated into the existing model. The assessment of the accuracy of the model is tested by comparing its predictions with the experimental data obtained in a 0.3-MWt ABFBC where a typical Turkish lignite is co-fired with limestone and cotton residue. Reasonable agreement is obtained between the predicted and measured O2, CO, CO2, SO2, NO, and N2O concentrations and temperature profiles. The results obtained in this study show that the addition of cotton residue increases emission of total nitrogenous species due to its high nitrogen content, but the main effect is observed in the increase of N2O formation. Furthermore, determination of the fuel nitrogen partitioning into char and volatiles and distribution of volatile nitrogen species are found to be the most important parameters for modeling of NO and N2O emissions in bubbling fluidized bed combustors.
- 8 November 2019
- Published by Taylor & Francis in Combustion Science and Technology
- Vol. 194 (2) , 435-448
Modeling of Fluidized Bed Combustion of Lignite with High Nitrogen Content Cotton Residue
A comprehensive system model, previously developed for prediction of combustion behaviors of Turkish lignites, lignite/hazelnut shell, and lignite/olive residue blends in a 0.3-MWt atmospheric bubbling fluidized bed combustor (ABFBC), is extended for modeling of co-combustion of Turkish lignite and cotton residue. Cotton residue has high nitrogen content (~4.1 wt% ar) unlike lignite (~0.9 wt% ar), olive residue (~1.6 wt% ar), and hazelnut shell (~0.5 wt% ar), which leads to relatively high emissions of nitric oxides (NOx) and nitrous oxide (N2O). For accurate prediction of emissions of NO and N2O, a sufficiently detailed NO and N2O formation and reduction reaction scheme is incorporated into the existing model. The assessment of the accuracy of the model is tested by comparing its predictions with the experimental data obtained in a 0.3-MWt ABFBC where a typical Turkish lignite is co-fired with limestone and cotton residue. Reasonable agreement is obtained between the predicted and measured O2, CO, CO2, SO2, NO, and N2O concentrations and temperature profiles. The results obtained in this study show that the addition of cotton residue increases emission of total nitrogenous species due to its high nitrogen content, but the main effect is observed in the increase of N2O formation. Furthermore, determination of the fuel nitrogen partitioning into char and volatiles and distribution of volatile nitrogen species are found to be the most important parameters for modeling of NO and N2O emissions in bubbling fluidized bed combustors.