P. Belo
Research Subjects
Research Interests
P. Belo has a total of 408 co-authors. Here are the top co-authors by number of shared publications:
Jet Efda Contributors
JET-EFDA, Culham Science Centre, Abingdon, OX14 3DB, UK
12 shared publicationsC. Giroud
European Atomic Energy Community
10 shared publications- Sven Wiesen
DIFFER—Dutch Institute for Fundamental Energy Research, Eindhoven, The Netherlands
10 shared publications - Sebastijan Brezinsek
Forschungszentrum Jülich
9 shared publications - Alexander Huber
Institute of Fusion Energy and Nuclear Waste Management-Plasma Physics, Forschungszentrum Jülich GmbH
8 shared publications - Maria Filomena Ferreira Nave
Associacao do Instituto Superior Tecnico para a Investigacao e Desenvolvimento, Lisboa, 1049-003, PORTUGAL
8 shared publications
Latest Publications
- 27 September 2013
- Published by IOP Publishing in Nuclear Fusion
- Vol. 53 (11)
Impact of nitrogen seeding on confinement and power load control of a high-triangularity JET ELMy H-mode plasma with a metal wall
- 27 September 2013
- Published by IOP Publishing in Nuclear Fusion
- Vol. 53 (11)
Impact of nitrogen seeding on confinement and power load control of a high-triangularity JET ELMy H-mode plasma with a metal wall
- 20 August 2013
- Published by IOP Publishing in Nuclear Fusion
- Vol. 53 (9)
Impact of carbon and tungsten as divertor materials on the scrape-off layer conditions in JET
- 20 August 2013
- Published by IOP Publishing in Nuclear Fusion
- Vol. 53 (9)
Impact of carbon and tungsten as divertor materials on the scrape-off layer conditions in JET
- Top Cited Papers
- 22 July 2013
- Published by IOP Publishing in Nuclear Fusion
- Vol. 53 (8) , 083023
Fuel retention studies with the ITER-Like Wall in JET
JET underwent a transformation from a full carbon-dominated tokamak to a fully metallic device with beryllium in the main chamber and a tungsten divertor. This material combination is foreseen for the activated phase of ITER. The ITER-Like Wall (ILW) experiment at JET shall demonstrate the plasma compatibility with metallic walls and the reduction in fuel retention. We report on a set of experiments (Ip = 2.0 MA, Bt = 2.0–2.4 T, δ = 0.2–0.4) in different confinement and plasma conditions with global gas balance analysis demonstrating a strong reduction in the long-term retention rate by more than a factor of 10 with respect to carbon-wall reference discharges. All experiments are executed in a series of identical plasma discharges in order to achieve maximum plasma duration until the analysis limit of the active gas handling system is reached. The composition analysis shows high purity of the recovered gas, typically 99% D. For typical L-mode discharges (Paux = 0.5 MW), type III (Paux = 5.0 MW) and type-I ELMy H-mode plasmas (Paux = 12.0 MW) a drop of the deuterium retention rate normalized to the operational time in divertor configuration is measured from 1.27 × 1021, 1.37 × 1021 and 1.97 × 1021 D s−1 down to 4.8 × 1019, 7.2 × 1019 and 16 × 1019 D s−1, respectively. The dynamic retention increases in the limiter phase in comparison with carbon-fibre composite, but also the outgassing after the discharge has risen in the same manner and overcompensates this transient retention. Overall an upper limit of the long-term retention rate of 1.5 × 1020 D s−1 is obtained with the ILW. The observed reduction by one order of magnitude confirms the expected predictions concerning the plasma-facing material change in ITER and is in line with identification of fuel co-deposition with Be as the main mechanism for the residual long-term retention. The reduction widens the operational space without active cleaning in the DT phase in comparison with a full carbon device.
- 22 July 2013
- Published by IOP Publishing in Nuclear Fusion
- Vol. 53 (8) , 083023
Top Cited PapersFuel retention studies with the ITER-Like Wall in JET
JET underwent a transformation from a full carbon-dominated tokamak to a fully metallic device with beryllium in the main chamber and a tungsten divertor. This material combination is foreseen for the activated phase of ITER. The ITER-Like Wall (ILW) experiment at JET shall demonstrate the plasma compatibility with metallic walls and the reduction in fuel retention. We report on a set of experiments (Ip = 2.0 MA, Bt = 2.0–2.4 T, δ = 0.2–0.4) in different confinement and plasma conditions with global gas balance analysis demonstrating a strong reduction in the long-term retention rate by more than a factor of 10 with respect to carbon-wall reference discharges. All experiments are executed in a series of identical plasma discharges in order to achieve maximum plasma duration until the analysis limit of the active gas handling system is reached. The composition analysis shows high purity of the recovered gas, typically 99% D. For typical L-mode discharges (Paux = 0.5 MW), type III (Paux = 5.0 MW) and type-I ELMy H-mode plasmas (Paux = 12.0 MW) a drop of the deuterium retention rate normalized to the operational time in divertor configuration is measured from 1.27 × 1021, 1.37 × 1021 and 1.97 × 1021 D s−1 down to 4.8 × 1019, 7.2 × 1019 and 16 × 1019 D s−1, respectively. The dynamic retention increases in the limiter phase in comparison with carbon-fibre composite, but also the outgassing after the discharge has risen in the same manner and overcompensates this transient retention. Overall an upper limit of the long-term retention rate of 1.5 × 1020 D s−1 is obtained with the ILW. The observed reduction by one order of magnitude confirms the expected predictions concerning the plasma-facing material change in ITER and is in line with identification of fuel co-deposition with Be as the main mechanism for the residual long-term retention. The reduction widens the operational space without active cleaning in the DT phase in comparison with a full carbon device.
- 1 July 2013
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 438, S1005-S1009
Simulations of tungsten transport in the edge of JET ELMy H-mode plasmas
- 1 July 2013
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 438, S1005-S1009
Simulations of tungsten transport in the edge of JET ELMy H-mode plasmas
- 11 June 2013
- Published by IOP Publishing in Nuclear Fusion
- Vol. 53 (7)
Modelling of hybrid scenario: from present-day experiments towards ITER
- 11 June 2013
- Published by IOP Publishing in Nuclear Fusion
- Vol. 53 (7)
Modelling of hybrid scenario: from present-day experiments towards ITER
- 15 January 2013
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 438, S175-S179
Target particle and heat loads in low-triangularity L-mode plasmas in JET with carbon and beryllium/tungsten walls
- 15 January 2013
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 438, S175-S179
Target particle and heat loads in low-triangularity L-mode plasmas in JET with carbon and beryllium/tungsten walls
- 14 June 2012
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 54 (7)
JET scrape-off-layer ionization at lower hybrid wave launching
- 14 June 2012
- Published by IOP Publishing in Plasma Physics and Controlled Fusion
- Vol. 54 (7)
JET scrape-off-layer ionization at lower hybrid wave launching
- 30 May 2012
- Published by IOP Publishing in Nuclear Fusion
- Vol. 52 (6)
Integration of a radiative divertor for heat load control into JET high triangularity ELMy H-mode plasmas
- 30 May 2012
- Published by IOP Publishing in Nuclear Fusion
- Vol. 52 (6)
Integration of a radiative divertor for heat load control into JET high triangularity ELMy H-mode plasmas
- 28 November 2011
- Published by IOP Publishing in Nuclear Fusion
- Vol. 52 (1)
Simulations of density profiles, pellet fuelling and density control in ITER
The paper presents the results of 1.5-dimensional simulations of density profiles and pellet fuelling for the ITER baseline scenario performed with the ASTRA and JETTO transport codes by the ITER Scenario Modelling working group within the European Task Force on Integrated Tokamak Modelling. The first part of the paper describes the physics of the problem and how it is implemented in the different codes available to the working group. The second part presents the results of the simulations. Results obtained with the GLF23 physics based transport model and a simplified description of the pellet particle source are described alongside results obtained with the simpler Bohm/gyro-Bohm semi-empirical transport model and a more sophisticated pellet ablation/deposition code providing a completely self-consistent description of the pellet source. A parametric study has been performed to assess the effect of varying parameters independently, the values of which in ITER are either uncertain or not easily controllable (such as particle diffusivity, edge stability, wall recycling and boundary conditions), on the target plasma density, temperature, Q and pellet frequency required to achieve a certain degree of density control. To this end the edge particle diffusivity was increased by a factor of three, the pedestal normalized critical pressure gradient for ballooning stability was decreased by 20%, the boundary conditions on density and temperature were modified by 30–40% and the wall recycling particle source was increased from zero to 20% of the particle outflux. The results show that variations in the order of 15% for density and temperature, 40% for Q and 100% for the pellet frequency can be expected. Open problems and modelling needs are also discussed in the paper.
- 28 November 2011
- Published by IOP Publishing in Nuclear Fusion
- Vol. 52 (1)
Simulations of density profiles, pellet fuelling and density control in ITER
The paper presents the results of 1.5-dimensional simulations of density profiles and pellet fuelling for the ITER baseline scenario performed with the ASTRA and JETTO transport codes by the ITER Scenario Modelling working group within the European Task Force on Integrated Tokamak Modelling. The first part of the paper describes the physics of the problem and how it is implemented in the different codes available to the working group. The second part presents the results of the simulations. Results obtained with the GLF23 physics based transport model and a simplified description of the pellet particle source are described alongside results obtained with the simpler Bohm/gyro-Bohm semi-empirical transport model and a more sophisticated pellet ablation/deposition code providing a completely self-consistent description of the pellet source. A parametric study has been performed to assess the effect of varying parameters independently, the values of which in ITER are either uncertain or not easily controllable (such as particle diffusivity, edge stability, wall recycling and boundary conditions), on the target plasma density, temperature, Q and pellet frequency required to achieve a certain degree of density control. To this end the edge particle diffusivity was increased by a factor of three, the pedestal normalized critical pressure gradient for ballooning stability was decreased by 20%, the boundary conditions on density and temperature were modified by 30–40% and the wall recycling particle source was increased from zero to 20% of the particle outflux. The results show that variations in the order of 15% for density and temperature, 40% for Q and 100% for the pellet frequency can be expected. Open problems and modelling needs are also discussed in the paper.
- 1 August 2011
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 415 (1) , S509-S512
EDGE2D-EIRENE modelling of the inter-ELM phase of H-mode plasmas on JET
- 1 August 2011
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 415 (1) , S509-S512
EDGE2D-EIRENE modelling of the inter-ELM phase of H-mode plasmas on JET