Viktor Šlapák
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Viktor Šlapák has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Frantisek Durovsky
Department of Electrical Engineering and Mechatronics, Faculty of Electrical Engineering and Informatics, Technical University of Košice, Letná 9, 042 00 Košice, Slovakia
10 shared publications - Karol Kyslan
Faculty of Electrical Engineering and Informatics, Dept. of Electrical Engineering and Mechatronics, Technical University of Košice, Košice, Slovak Republic
10 shared publications - Matúš Hric
SPINEA Ltd ., 080 01 Haniska , Prešov , Slovakia
4 shared publications - Jozef Ivan
SPINEA Ltd ., 080 01 Haniska , Prešov , Slovakia
3 shared publications Milan Lacko
Department of Electrical Engineering and Mechatronics, Faculty of Electrical Engineering and Informatics, Technical University of Košice, Letná 9, 042 00 Košice, Slovakia
3 shared publications- Ján Bačík
Technical University of Košice
2 shared publications
Latest Publications
- Open Access
- 1 January 2024
- Published by Walter de Gruyter GmbH in Power Electronics and Drives
- Vol. 9 (1) , 482-501
Shearing Work Analysis and Control Design of Rotary Shears in Material Processing Lines
Rotary shears are common part of the material processing lines (MPL). During the operation, these shears are loaded with impact cutting torque, which takes only short time but reaches values compared to motor-rated torque. Therefore, it is a technical challenge to ensure the speed stability during the cut. The presented paper deals with the analysis of the rotary shears’ operation and material cutting process from the control point of view and presents a cutting torque compensation possibility. Three types of speed controllers without and with cutting torque compensation are compared.
- 1 January 2024
- Published by Walter de Gruyter GmbH in Power Electronics and Drives
- Vol. 9 (1) , 482-501
Open AccessShearing Work Analysis and Control Design of Rotary Shears in Material Processing Lines
Rotary shears are common part of the material processing lines (MPL). During the operation, these shears are loaded with impact cutting torque, which takes only short time but reaches values compared to motor-rated torque. Therefore, it is a technical challenge to ensure the speed stability during the cut. The presented paper deals with the analysis of the rotary shears’ operation and material cutting process from the control point of view and presents a cutting torque compensation possibility. Three types of speed controllers without and with cutting torque compensation are compared.
- Open Access
A Nonlinear Controller for Point-to-Point Position Control
Position control algorithms can be classified into two groups: point-to-point control and continuous path control. For point-to-point control implemented in programmable logic controllers, the speed setpoint is mostly the only setpoint transmitted to the industrial converter. Incorrect settings of the position controller in PLC may lead to position overshoot or oscillations, which are unacceptable in position control applications. The speed control structure in the industrial converter usually has a fixed structure which does not allow the implementation of advanced speed controller. Moreover, standard library blocks for position control encounter difficulties in diagnostics and tuning. To address these limitations, this paper proposes a novel solution for position control that achieves time-optimal speed trajectory during acceleration and enhanced capabilities during deceleration. The proposed controller was verified by simulations of positioning of zinc ingot feeder unit drive and compared with a standard P-controller. Experimental results confirmed the performance of the proposed controller with the industrial application of a feeder unit.
Open AccessA Nonlinear Controller for Point-to-Point Position Control
Position control algorithms can be classified into two groups: point-to-point control and continuous path control. For point-to-point control implemented in programmable logic controllers, the speed setpoint is mostly the only setpoint transmitted to the industrial converter. Incorrect settings of the position controller in PLC may lead to position overshoot or oscillations, which are unacceptable in position control applications. The speed control structure in the industrial converter usually has a fixed structure which does not allow the implementation of advanced speed controller. Moreover, standard library blocks for position control encounter difficulties in diagnostics and tuning. To address these limitations, this paper proposes a novel solution for position control that achieves time-optimal speed trajectory during acceleration and enhanced capabilities during deceleration. The proposed controller was verified by simulations of positioning of zinc ingot feeder unit drive and compared with a standard P-controller. Experimental results confirmed the performance of the proposed controller with the industrial application of a feeder unit.
- Open Access
- 1 January 2023
- Published by Walter de Gruyter GmbH in Power Electronics and Drives
- Vol. 8 (1) , 53-64
Emulation of Mechanical Loads in Electric Drives – An Overview of Methods
Sciendo provides publishing services and solutions to academic and professional organizations and individual authors. We publish journals, books, conference proceedings and a variety of other publications.
- 1 January 2023
- Published by Walter de Gruyter GmbH in Power Electronics and Drives
- Vol. 8 (1) , 53-64
Open AccessEmulation of Mechanical Loads in Electric Drives – An Overview of Methods
Sciendo provides publishing services and solutions to academic and professional organizations and individual authors. We publish journals, books, conference proceedings and a variety of other publications.
- Open Access
Measurement and Modelling of a Cycloidal Gearbox in Actuator with Permanent Magnet Synchronous Machine
Compact geared servo drives are a common part of modern industrial automation; thus, their proper modelling is a necessary part for the application and control design. The presented paper focuses on the mathematical model of the cycloidal gearbox, which is used in the compact actuator with a permanent magnet synchronous motor. A measurement procedure to obtain the necessary gearbox parameters is presented along with its mathematical model. A new approach was used to model the stiction and nonlinear gearbox friction behaviour in all four quadrants. A simulation of the actuator with the modelled gearbox is described and its results are compared with the real system measurement. Obtained results show a high match between simulation and experimental results and confirm the correctness of the simulation model.
Open AccessMeasurement and Modelling of a Cycloidal Gearbox in Actuator with Permanent Magnet Synchronous Machine
Compact geared servo drives are a common part of modern industrial automation; thus, their proper modelling is a necessary part for the application and control design. The presented paper focuses on the mathematical model of the cycloidal gearbox, which is used in the compact actuator with a permanent magnet synchronous motor. A measurement procedure to obtain the necessary gearbox parameters is presented along with its mathematical model. A new approach was used to model the stiction and nonlinear gearbox friction behaviour in all four quadrants. A simulation of the actuator with the modelled gearbox is described and its results are compared with the real system measurement. Obtained results show a high match between simulation and experimental results and confirm the correctness of the simulation model.
- Open Access
A Comparative Study and Optimization of Switching Functions for Sliding-Mode Observer in Sensorless Control of PMSM
The sensorless control of the permanent magnet synchronous motor (PMSM) has attracted wide attention due to its high reliability, economic and safety benefits. A fast and high-precision rotor-position estimation is inevitable for the implementation of sensorless control. Sliding-mode observer (SMO) is a preferred solution for sensorless control by many industrial companies. This article addresses the comparison of different switching functions employed in the control structure of sensorless field-oriented control with SMO. The switching functions are classified and their influence on the performance of the PMSM is verified for different shaping coefficients (SC). In addition, a statistical evaluation of the switching functions is provided to find the optimal values of SC. An experimental and statistical evaluation validated the substitutability of signum and hyperbolic switching functions and optimal values of SC have been found.
Open AccessA Comparative Study and Optimization of Switching Functions for Sliding-Mode Observer in Sensorless Control of PMSM
The sensorless control of the permanent magnet synchronous motor (PMSM) has attracted wide attention due to its high reliability, economic and safety benefits. A fast and high-precision rotor-position estimation is inevitable for the implementation of sensorless control. Sliding-mode observer (SMO) is a preferred solution for sensorless control by many industrial companies. This article addresses the comparison of different switching functions employed in the control structure of sensorless field-oriented control with SMO. The switching functions are classified and their influence on the performance of the PMSM is verified for different shaping coefficients (SC). In addition, a statistical evaluation of the switching functions is provided to find the optimal values of SC. An experimental and statistical evaluation validated the substitutability of signum and hyperbolic switching functions and optimal values of SC have been found.
- 21 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Load Emulation for Testing of Electrical Actuators in Industrial Applications
Geared servodrives are tested with different types of short-term or long-term tests. This paper presents the industrial approach to load emulation in the testing process of electrical actuators. Presented emulation method is based on the real dataset provided by the customer. This dataset is modified, processed, and then used for the calculation of a load torque reference for the drive loading actuator under test. The final implementation is done with industrial drives controlled by PLC. NI PXI was used as a graphical user interface and for data acquisition. Experimental results that confirm the correctness of the implementation are included.
- 21 June 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-5
Load Emulation for Testing of Electrical Actuators in Industrial Applications
Geared servodrives are tested with different types of short-term or long-term tests. This paper presents the industrial approach to load emulation in the testing process of electrical actuators. Presented emulation method is based on the real dataset provided by the customer. This dataset is modified, processed, and then used for the calculation of a load torque reference for the drive loading actuator under test. The final implementation is done with industrial drives controlled by PLC. NI PXI was used as a graphical user interface and for data acquisition. Experimental results that confirm the correctness of the implementation are included.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 297-302
Design of load torque and mechanical speed estimator of PMSM with unscented Kalman filter — An engineering guide
This paper presents the design of Unscented Kalman Filter (UKF) for estimation of state space variables of permanent magnet synchronous machine (PMSM). The UKF is shown together with the field oriented speed control. At first, the position and the speed of PMSM are measured, and UKF is used only for a load torque estimation. It is indicated how differences in sampling time of the speed and the current loop affects overall estimation performance. Subsequently, speed sensorless performance of the UKF with the same parameters is shown for comparison. Designed filter is verified only by Matlab simulation.
- 1 October 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 297-302
Design of load torque and mechanical speed estimator of PMSM with unscented Kalman filter — An engineering guide
This paper presents the design of Unscented Kalman Filter (UKF) for estimation of state space variables of permanent magnet synchronous machine (PMSM). The UKF is shown together with the field oriented speed control. At first, the position and the speed of PMSM are measured, and UKF is used only for a load torque estimation. It is indicated how differences in sampling time of the speed and the current loop affects overall estimation performance. Subsequently, speed sensorless performance of the UKF with the same parameters is shown for comparison. Designed filter is verified only by Matlab simulation.
- Open Access
- 1 January 2016
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2016, 1-10
Finite Control Set Model Predictive Speed Control of a DC Motor
The paper describes the design procedure for a finite control set model predictive control (FCS-MPC) of brushed permanent magnet DC (PMDC) machine supplied from DC-DC converter. Full order linear Kalman filter is used for estimation of an unmeasured load torque and reduction of speed measurement noise. A new cost function has been introduced with a feedforward dynamic current component and a feedforward static load current component. The performance of the proposed control strategy is compared to the conventional PI-PWM cascade speed control through the experimental verification on the 250 W laboratory prototype. Obtained results show excellent dynamic behaviour and indicate possible energy savings of the proposed speed control.
- 1 January 2016
- Published by Wiley in Mathematical Problems in Engineering
- Vol. 2016, 1-10
Open AccessFinite Control Set Model Predictive Speed Control of a DC Motor
The paper describes the design procedure for a finite control set model predictive control (FCS-MPC) of brushed permanent magnet DC (PMDC) machine supplied from DC-DC converter. Full order linear Kalman filter is used for estimation of an unmeasured load torque and reduction of speed measurement noise. A new cost function has been introduced with a feedforward dynamic current component and a feedforward static load current component. The performance of the proposed control strategy is compared to the conventional PI-PWM cascade speed control through the experimental verification on the 250 W laboratory prototype. Obtained results show excellent dynamic behaviour and indicate possible energy savings of the proposed speed control.
- 1 October 2015
- Published by International Hellenic University in Journal of Engineering Science and Technology Review
- Vol. 8 (5) , 128-133
Nonlinear Speed Control of Permanent Magnet Synchronous Motor with Salient Poles
- 1 October 2015
- Published by International Hellenic University in Journal of Engineering Science and Technology Review
- Vol. 8 (5) , 128-133
Nonlinear Speed Control of Permanent Magnet Synchronous Motor with Salient Poles
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 124-129
Cost functions in finite control set model predictive control of permanent magnet DC machine
This paper presents a finite control set model predictive control strategy for the speed control of brushed permanent magnet DC machine. Main objective is to introduce and compare basic cost functions regarding speed control. Full order Kalman filter is used for the observation of the non-measured load torque and reduction of speed measurement noise. Influence of the proposed cost functions on the control quality is demonstrated by simulations. The performance of the best cost function is shown through experimental verification with a 250 W machine and laboratory prototype of H-bridge controlled by RT-LAB control platform.
- 1 September 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 124-129
Cost functions in finite control set model predictive control of permanent magnet DC machine
This paper presents a finite control set model predictive control strategy for the speed control of brushed permanent magnet DC machine. Main objective is to introduce and compare basic cost functions regarding speed control. Full order Kalman filter is used for the observation of the non-measured load torque and reduction of speed measurement noise. Influence of the proposed cost functions on the control quality is demonstrated by simulations. The performance of the best cost function is shown through experimental verification with a 250 W machine and laboratory prototype of H-bridge controlled by RT-LAB control platform.