Abdeljebbar Diouri
Research Subjects
Abdeljebbar Diouri has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
A. Boukhari
Laboratoire de Physico-Chimie des Matériaux Inorganiques et Organiques, Université Mohammed V Agdal, Ecole Normale Supérieure Rabat Maroc
7 shared publicationsJ. Aride
Laboratoire de Physico-Chimie des Matériaux, LAF 502, E.N.S. Takaddoum, BP. 5118, 10000 Rabat, Morocco
5 shared publicationsM. Taibi
Laboratoire de Physico-Chimie des Matériaux Inorganiques et Organiques, Université Mohammed V Agdal, Ecole Normale Supérieure Rabat Maroc
4 shared publicationsAli Boukhari
3 shared publicationsM. Alami Talbi
Laboratoire de Chimie du Solide Appliquée, Faculté des Sciences, Université MohammedV-Agdal, 10000 Rabat, Maroc
3 shared publicationsMy.Y. Benarchid
3 shared publications
Latest Publications
- 1 June 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 247
Improvement of hydraulic and mechanical properties of dicalcium silicate by alkaline activation
- 1 June 2020
- Published by Elsevier in Construction and Building Materials
- Vol. 247
Improvement of hydraulic and mechanical properties of dicalcium silicate by alkaline activation
- Open Access
- 30 September 2018
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 68 (331) , e166
Moroccan oil shale and coal waste as alternative raw materials in Portland cement clinker manufacture. Clinkerisation reactions and clinker characterisation
For some time the cement industry has been seeking procedures to effectively lower the higher energy costs involved in cement manufacture. Timahdit oil shale and Jerada coal waste could potentially be used as alternative raw materials to produce clinker. This study explored the possibility of applying those materials to a greener use, based on the reactivity and burnability of raw mixes containing Moroccan oil shale and coal waste. The findings showed that, irrespective of particle size, oil shale mixes delivered higher reactivity than coal waste materials, although reactivity was highest in the oil shale clinker with a particle size < 45 μm. The clinkers bearing oil shale with a particle size < 90 μm or a blend of oil shale and coal waste with a size < 45 μm contained higher proportions of alite ( > 70 %).
- 30 September 2018
- Published by Editorial CSIC in Materiales de Construcción
- Vol. 68 (331) , e166
Open AccessMoroccan oil shale and coal waste as alternative raw materials in Portland cement clinker manufacture. Clinkerisation reactions and clinker characterisation
For some time the cement industry has been seeking procedures to effectively lower the higher energy costs involved in cement manufacture. Timahdit oil shale and Jerada coal waste could potentially be used as alternative raw materials to produce clinker. This study explored the possibility of applying those materials to a greener use, based on the reactivity and burnability of raw mixes containing Moroccan oil shale and coal waste. The findings showed that, irrespective of particle size, oil shale mixes delivered higher reactivity than coal waste materials, although reactivity was highest in the oil shale clinker with a particle size < 45 μm. The clinkers bearing oil shale with a particle size < 90 μm or a blend of oil shale and coal waste with a size < 45 μm contained higher proportions of alite ( > 70 %).
- Open Access
- 20 May 2014
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 11, 01048
Degradation of Alumina and Magnesia Chrome refractory bricks in Portland cement kiln – Corrected version*
- 20 May 2014
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 11, 01048
Open AccessDegradation of Alumina and Magnesia Chrome refractory bricks in Portland cement kiln – Corrected version*
- Open Access
- 28 April 2014
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 11, 01009
Characterization of Moroccan coal waste: valorization in the elaboration of the Portland clinker
Coal exploited in the mine of Jerada (northeast of Morocco) was accompanied by large quantities of waste. The purpose of this work is to characterize this waste with the aim of its use as a material for civil engineering. Mineral and chemical investigations on this waste in the raw state, and at different temperature of heat treatments, were carried out by various methods: X-ray fluorescence, X-ray diffraction, infrared spectroscopy. These analyzes showed that the studied waste, contain essentially a mineral part formed by silica and various clays, as well as coal’s residues. The thermal investigation of waste, by differential scanning calorimetry (DSC), revealed an exothermic phenomenon attributed to the combustion of coal residues. Other phenomena were noted on the thermograms due to the mineral part transformations. In this analysis a comparison was also made with pure coal. These characteristics of coal waste encourage studying its development in reducing energy consumption in the Portland cement manufacture. Mixtures of waste with limestone or with raw cement materials were studied, and the resulting products were analyzed by different methods.
- 28 April 2014
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 11, 01009
Open AccessCharacterization of Moroccan coal waste: valorization in the elaboration of the Portland clinker
Coal exploited in the mine of Jerada (northeast of Morocco) was accompanied by large quantities of waste. The purpose of this work is to characterize this waste with the aim of its use as a material for civil engineering. Mineral and chemical investigations on this waste in the raw state, and at different temperature of heat treatments, were carried out by various methods: X-ray fluorescence, X-ray diffraction, infrared spectroscopy. These analyzes showed that the studied waste, contain essentially a mineral part formed by silica and various clays, as well as coal’s residues. The thermal investigation of waste, by differential scanning calorimetry (DSC), revealed an exothermic phenomenon attributed to the combustion of coal residues. Other phenomena were noted on the thermograms due to the mineral part transformations. In this analysis a comparison was also made with pure coal. These characteristics of coal waste encourage studying its development in reducing energy consumption in the Portland cement manufacture. Mixtures of waste with limestone or with raw cement materials were studied, and the resulting products were analyzed by different methods.
- Open Access
- 3 September 2012
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 2, 01018
Ajout de phosphogypse à des mortiers à base de cendres volantes et filler calcaire
The objective of this paper is to study the possibility of valorization of phosphogypsum in building materials because his large availability as a by-product of the phosphate industry. We study the effect of adding phosphogypsum on a mixture of clinker, fly ash and limestone filler. The samples were prepared by adding 10% of phosphogypsum and 30% of fly ash to mixtures consisting of clinker and limestone filler. The mixtures are hydrated and characterized by X-ray diffraction and Infrared spectroscopy. Crystalline phases grow from the third day, and we note that the most common phases are: Portlandite Ca(OH) 2 , CaCO 3 calcite, ettringite Ca 6 Al 2 (SO 4) 3 (OH) 12 .26H 2 O, Ca 5 (SiO4) 2 (OH) 2 and gypsum CaSO 4 ,2H 2 O but their percentages vary depending on the mixtures. Measuring the setting time of mortars shows that the beginning and end of setting are usually delayed in proportion to the addition of fly ash and phosphogypsum. The microstructure of materials was also studied by measuring the apparent permeability; the results show that the addition of phosphogypsum has contributed to a decrease in the permeability of the samples against fly ash has the opposite effect. The compressive strength of mortars shows concordant results, the strengths increase with the decrease in permeability.
- 3 September 2012
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 2, 01018
Open AccessAjout de phosphogypse à des mortiers à base de cendres volantes et filler calcaire
The objective of this paper is to study the possibility of valorization of phosphogypsum in building materials because his large availability as a by-product of the phosphate industry. We study the effect of adding phosphogypsum on a mixture of clinker, fly ash and limestone filler. The samples were prepared by adding 10% of phosphogypsum and 30% of fly ash to mixtures consisting of clinker and limestone filler. The mixtures are hydrated and characterized by X-ray diffraction and Infrared spectroscopy. Crystalline phases grow from the third day, and we note that the most common phases are: Portlandite Ca(OH) 2 , CaCO 3 calcite, ettringite Ca 6 Al 2 (SO 4) 3 (OH) 12 .26H 2 O, Ca 5 (SiO4) 2 (OH) 2 and gypsum CaSO 4 ,2H 2 O but their percentages vary depending on the mixtures. Measuring the setting time of mortars shows that the beginning and end of setting are usually delayed in proportion to the addition of fly ash and phosphogypsum. The microstructure of materials was also studied by measuring the apparent permeability; the results show that the addition of phosphogypsum has contributed to a decrease in the permeability of the samples against fly ash has the opposite effect. The compressive strength of mortars shows concordant results, the strengths increase with the decrease in permeability.
- Open Access
- 3 September 2012
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 2, 01005
Hydration behavior of iron doped calcium sulfoaluminate phase at room temperature
Different samples of calcium sulfoaluminate phase doped with iron, (Ca 4 Al (6-2x) Fe 2x SO 16) with x = 0, 0.2 and 0.5, were synthesized at 1350°C. The hydration kinetics of the resulted phases was investigated by calorimetric and conductimetric techniques. The hydrated samples were analyzed by X-ray diffraction and scanning electron microscopy. The hydration of calcium sulfoaluminate was slightly modified by inclusion of iron in its structure. Dissolution rate of calcium sulfoaluminate phase doped with iron appeared to be slowed down such as the nucleation rate during the induction period while the percentage of reaction after 1 day was slightly increased. The analysis of hydrates indicated the formation of the same hydrates, ettringite and calcium monosulfoaluminate and the gibbsite, with or without iron replacement. Gibbsite played a major role in the kinetics of the induction period and thus the presence of iron may decrease its nucleation rate forming (A, F)H 3 instead of AH 3 .
- 3 September 2012
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 2, 01005
Open AccessHydration behavior of iron doped calcium sulfoaluminate phase at room temperature
Different samples of calcium sulfoaluminate phase doped with iron, (Ca 4 Al (6-2x) Fe 2x SO 16) with x = 0, 0.2 and 0.5, were synthesized at 1350°C. The hydration kinetics of the resulted phases was investigated by calorimetric and conductimetric techniques. The hydrated samples were analyzed by X-ray diffraction and scanning electron microscopy. The hydration of calcium sulfoaluminate was slightly modified by inclusion of iron in its structure. Dissolution rate of calcium sulfoaluminate phase doped with iron appeared to be slowed down such as the nucleation rate during the induction period while the percentage of reaction after 1 day was slightly increased. The analysis of hydrates indicated the formation of the same hydrates, ettringite and calcium monosulfoaluminate and the gibbsite, with or without iron replacement. Gibbsite played a major role in the kinetics of the induction period and thus the presence of iron may decrease its nucleation rate forming (A, F)H 3 instead of AH 3 .
- Open Access
- 3 September 2012
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 2, 01003
Permeability and mechanical properties of cement mortars colored by nano-mineral additives
This work concerns a preliminary study on issues that relate primarily to the permeability of cementitious materials under the influence of some specific inexpensive additions that can play an important role in preserving the environment. We studied the addition of dyes in the presence of TiO 2 on the Portland cement mortar. The used dyes are a yellow powder containing iron oxyhydroxide (FeO (OH)), a blue-based powder tellurate manganese (MnTe 2 O 5) and red powder containing iron oxide (Fe 2 O 3). We measure the setting time, permeability and mechanical properties of Portland cement mortars colored with nano-mineral oxides mentioned previously. Test results indicate that the addition of nano-particles has a little influence on the setting time, improves penetration resistance that is due the affinity of the pore structure of mortar and slightly improves the resistance to compression for low levels of nanoparticles of TiO 2 .
- 3 September 2012
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 2, 01003
Open AccessPermeability and mechanical properties of cement mortars colored by nano-mineral additives
This work concerns a preliminary study on issues that relate primarily to the permeability of cementitious materials under the influence of some specific inexpensive additions that can play an important role in preserving the environment. We studied the addition of dyes in the presence of TiO 2 on the Portland cement mortar. The used dyes are a yellow powder containing iron oxyhydroxide (FeO (OH)), a blue-based powder tellurate manganese (MnTe 2 O 5) and red powder containing iron oxide (Fe 2 O 3). We measure the setting time, permeability and mechanical properties of Portland cement mortars colored with nano-mineral oxides mentioned previously. Test results indicate that the addition of nano-particles has a little influence on the setting time, improves penetration resistance that is due the affinity of the pore structure of mortar and slightly improves the resistance to compression for low levels of nanoparticles of TiO 2 .
- 1 August 2010
- Published by Elsevier in Cement and Concrete Research
- Vol. 40 (8) , 1314-1319
Characterisation of iron inclusion during the formation of calcium sulfoaluminate phase
- 1 August 2010
- Published by Elsevier in Cement and Concrete Research
- Vol. 40 (8) , 1314-1319
Characterisation of iron inclusion during the formation of calcium sulfoaluminate phase
- 31 July 2006
- Published by International Information and Engineering Technology Association in European Journal of Control
- Vol. 31 (4)
Etude de la réactivité hydraulique d'un ciment composite par des analyses thermiques
Etude de la réactivité hydraulique d'un ciment composite par des analyses thermiques Study of the hydraulic reactivity of a composite cement by thermal analysis.
- 31 July 2006
- Published by International Information and Engineering Technology Association in European Journal of Control
- Vol. 31 (4)
Etude de la réactivité hydraulique d'un ciment composite par des analyses thermiques
Etude de la réactivité hydraulique d'un ciment composite par des analyses thermiques Study of the hydraulic reactivity of a composite cement by thermal analysis.
- 31 July 2006
- Published by International Information and Engineering Technology Association in European Journal of Control
- Vol. 31 (4) , 381-392
Réactivité hydraulique des silicates bicalciques et des clinkers bélitiques dopés au chrome et au phosphore
Réactivité hydraulique des silicates bicalciques et des clinkers bélitiques dopés au chrome et au phosphore Hydration reactivity of chromium-phosphorus doped dicalcium silicates and belitic clinkers
- 31 July 2006
- Published by International Information and Engineering Technology Association in European Journal of Control
- Vol. 31 (4) , 381-392
Réactivité hydraulique des silicates bicalciques et des clinkers bélitiques dopés au chrome et au phosphore
Réactivité hydraulique des silicates bicalciques et des clinkers bélitiques dopés au chrome et au phosphore Hydration reactivity of chromium-phosphorus doped dicalcium silicates and belitic clinkers