Marcel Utz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Marcel Utz has a total of 121 co-authors. Here are the top co-authors by number of shared publications:
Manvendra Sharma
School of Chemistry, University of Southampton, UK
13 shared publicationsWilliam Hale
School of Chemistry, University of Southampton, Southampton SO17 1BJ, United Kingdom
8 shared publications- Sylwia Joanna Barker
School of Chemistry, University of Southampton, UK
7 shared publications - Malcolm Harris Levitt
School of Chemistry University of Southampton SO17 1BJ UK
6 shared publications Bishnubrata Patra
School of Chemistry, University of Southampton, UK
4 shared publications- James Eills
Institute of Biological Information Processing (IBI-7), Forschungszentrum Jülich, Jülich, Germany
4 shared publications
Latest Publications
- Open Access
- 15 September 2026
- Published by Elsevier in SSRN Electronic Journal
3D Printed Hyperpolarization Compatible NMR Tubes
Magnetic resonance (MR) phenomena have proven themselves in high-precision spectroscopy with NMR and in in situ tomography with MRI. Fabrication of the novel devices and experiments largely relies on multi-step procedures that are time-consuming and equipment-intensive. Digital light processing (DLP), in part, offers a single-step fabrication, significantly dropping the costs, and allows rapid prototyping of the devices within a few micron resolution. However, the selection of DLP resins must be carefully considered. Many DLP resins undergo chemical degradation in liquid state MR, resulting in spectral artifacts; with only a few outstanding cases holding up in aggressive solvents. In this study, we investigate the effect of solvents on the most utilized and market-available resins and compare the reliability of DLP-processed devices for MR. Specifically, we selected and assessed the best resins and 3D-printed them following the designs of standard NMR tubes, with circular and hexagonal cross-sections. Finally, we also tested them in an example application, namely Signal Amplification by Reversible Exchange (SABRE) hyperpolarization with parahydrogen. This not only demonstrated that the tubes can be pressurized up to ∼5 bar, but also their suitability for NMR experiments, including a radiofrequency amplification by stimulated emission of radiation (RASER) experiment.
- 15 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open Access3D Printed Hyperpolarization Compatible NMR Tubes
Magnetic resonance (MR) phenomena have proven themselves in high-precision spectroscopy with NMR and in in situ tomography with MRI. Fabrication of the novel devices and experiments largely relies on multi-step procedures that are time-consuming and equipment-intensive. Digital light processing (DLP), in part, offers a single-step fabrication, significantly dropping the costs, and allows rapid prototyping of the devices within a few micron resolution. However, the selection of DLP resins must be carefully considered. Many DLP resins undergo chemical degradation in liquid state MR, resulting in spectral artifacts; with only a few outstanding cases holding up in aggressive solvents. In this study, we investigate the effect of solvents on the most utilized and market-available resins and compare the reliability of DLP-processed devices for MR. Specifically, we selected and assessed the best resins and 3D-printed them following the designs of standard NMR tubes, with circular and hexagonal cross-sections. Finally, we also tested them in an example application, namely Signal Amplification by Reversible Exchange (SABRE) hyperpolarization with parahydrogen. This not only demonstrated that the tubes can be pressurized up to ∼5 bar, but also their suitability for NMR experiments, including a radiofrequency amplification by stimulated emission of radiation (RASER) experiment.
- Open Access
- 4 February 2026
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 26 (6) , 2023-2034
Microfluidic NMR for operando monitoring of drug-induced metabolic fluxes in liver tissue slices
Monitoring metabolism in living tissues with high temporal resolution and broad metabolite coverage through microfluidic NMR.
- 4 February 2026
- Published by Royal Society of Chemistry (RSC) in Lab on a Chip
- Vol. 26 (6) , 2023-2034
Open AccessMicrofluidic NMR for operando monitoring of drug-induced metabolic fluxes in liver tissue slices
Monitoring metabolism in living tissues with high temporal resolution and broad metabolite coverage through microfluidic NMR.
- Open Access
- 24 October 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (43) , eady9103
Chemical hydrodynamics of nuclear spin states
Quantum mechanical equations of motion are strictly linear in density operators, but equations describing chemical kinetics and hydrodynamics may be nonlinear in concentrations. This incompatibility is fundamental, but special cases can be handled—for example, in magnetic resonance where nuclear spin interactions may be too weak influence concentration dynamics. For isolated spins and first-order reactions, this is a well-researched topic, but time evolution of complex nuclear spin systems in the presence of second-order kinetics, diffusion, and flow has so far remained intractable. In this communication, we report a numerically stable formalism for time-domain description of nuclear spin dynamics and relaxation in the simultaneous presence of diffusion, flow, and second-order chemical reactions. As an illustration, we use Diels-Alder cycloaddition of acrylonitrile to cyclopentadiene in the presence of diffusion and flow in a microfluidic NMR probe (a finite element model with thousands of Voronoi cells) with a spatially localized stripline radio frequency coil.
- 24 October 2025
- Published by American Association for the Advancement of Science (AAAS) in Science Advances
- Vol. 11 (43) , eady9103
Open AccessChemical hydrodynamics of nuclear spin states
Quantum mechanical equations of motion are strictly linear in density operators, but equations describing chemical kinetics and hydrodynamics may be nonlinear in concentrations. This incompatibility is fundamental, but special cases can be handled—for example, in magnetic resonance where nuclear spin interactions may be too weak influence concentration dynamics. For isolated spins and first-order reactions, this is a well-researched topic, but time evolution of complex nuclear spin systems in the presence of second-order kinetics, diffusion, and flow has so far remained intractable. In this communication, we report a numerically stable formalism for time-domain description of nuclear spin dynamics and relaxation in the simultaneous presence of diffusion, flow, and second-order chemical reactions. As an illustration, we use Diels-Alder cycloaddition of acrylonitrile to cyclopentadiene in the presence of diffusion and flow in a microfluidic NMR probe (a finite element model with thousands of Voronoi cells) with a spatially localized stripline radio frequency coil.
- Open Access
Operando Monitoring of Metabolic Fluxes In Cholestatic Murine Liver Tissue Slices By Microfluidic NMR
Monitoring metabolism in living tissues with high temporal resolution and broad metabo-lite coverage remains a major challenge. We introduce TISuMR, a microfluidic Lab-on-a-Chip platform that enables continuous, non-invasive operando NMR spectroscopy of live tissue slices. The TISuMR platform replaces the conventional NMR sample tube with a fully integrated microfluidic culture system that maintains tissue viability through dynamic nutrient perifusion, gas exchange via a diffusion membrane, and precise temperature control. Coupled with a custom-designed micro-NMR probe, the platform allows detection of nearly two dozens of metabolites from just 2.5 µ L of sample. In a proof-of-concept study, we demonstrate the platform’s unique ability to resolve dynamic metabolic fluxes and to monitor, in real time, the onset of chlorpromazine-induced cholestasis in murine liver tissue, with a time resolution of just over three minutes. This approach provides a powerful, minimally disruptive tool for studying tissue metabolism in real time.
Open AccessOperando Monitoring of Metabolic Fluxes In Cholestatic Murine Liver Tissue Slices By Microfluidic NMR
Monitoring metabolism in living tissues with high temporal resolution and broad metabo-lite coverage remains a major challenge. We introduce TISuMR, a microfluidic Lab-on-a-Chip platform that enables continuous, non-invasive operando NMR spectroscopy of live tissue slices. The TISuMR platform replaces the conventional NMR sample tube with a fully integrated microfluidic culture system that maintains tissue viability through dynamic nutrient perifusion, gas exchange via a diffusion membrane, and precise temperature control. Coupled with a custom-designed micro-NMR probe, the platform allows detection of nearly two dozens of metabolites from just 2.5 µ L of sample. In a proof-of-concept study, we demonstrate the platform’s unique ability to resolve dynamic metabolic fluxes and to monitor, in real time, the onset of chlorpromazine-induced cholestasis in murine liver tissue, with a time resolution of just over three minutes. This approach provides a powerful, minimally disruptive tool for studying tissue metabolism in real time.
- 8 August 2024
- Published by American Chemical Society (ACS) in Analytical Chemistry
- Vol. 96 (33) , 13588-13597
Exploration of Materials for Three-Dimensional NMR Microcoil Production via CNC Micromilling and Laser Etching
The excellent versatility of 5-axis computer numerical control (CNC) micromilling has led to its application for prototyping NMR microcoils tailored to mass-limited samples (reducing development time and cost). However, vibrations during 5-axis milling can hinder the creation of complex 3D volume microcoils (i.e., solenoids and saddle coils). To address these limitations, a high-resolution NSCNC ELARA 4-axis milling machine was developed with the extra precision required for making complex 3D volume microcoils. Upon investigating the performance of resonators made with various copper-coated dielectrics, resonators with poly(methyl methacrylate) (PMMA) provided the best SNR/line shape. Thus, complex 1.7 mm microcoil designs were machined from Cu-coated PMMA. A milled 6.4 mm solenoid also provided 6.6× the total carbon signal for a 13C-labeled broccoli seed compared to a commercial inverse 5 mm NMR probe (demonstrating potential for larger coil designs). However, the manufacture of coils 13C-labeled algae extract, while the solenoid was further tested on two copepod egg sacs (∼4 μg of total sample). In summary, the flexibility to prototype complex microcoils in-house allows laboratories to tailor microcoils to specific mass-limited samples while avoiding the costs of cleanrooms.
- 8 August 2024
- Published by American Chemical Society (ACS) in Analytical Chemistry
- Vol. 96 (33) , 13588-13597
Exploration of Materials for Three-Dimensional NMR Microcoil Production via CNC Micromilling and Laser Etching
The excellent versatility of 5-axis computer numerical control (CNC) micromilling has led to its application for prototyping NMR microcoils tailored to mass-limited samples (reducing development time and cost). However, vibrations during 5-axis milling can hinder the creation of complex 3D volume microcoils (i.e., solenoids and saddle coils). To address these limitations, a high-resolution NSCNC ELARA 4-axis milling machine was developed with the extra precision required for making complex 3D volume microcoils. Upon investigating the performance of resonators made with various copper-coated dielectrics, resonators with poly(methyl methacrylate) (PMMA) provided the best SNR/line shape. Thus, complex 1.7 mm microcoil designs were machined from Cu-coated PMMA. A milled 6.4 mm solenoid also provided 6.6× the total carbon signal for a 13C-labeled broccoli seed compared to a commercial inverse 5 mm NMR probe (demonstrating potential for larger coil designs). However, the manufacture of coils 13C-labeled algae extract, while the solenoid was further tested on two copepod egg sacs (∼4 μg of total sample). In summary, the flexibility to prototype complex microcoils in-house allows laboratories to tailor microcoils to specific mass-limited samples while avoiding the costs of cleanrooms.
- Open Access
- 25 June 2024
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 146 (27) , 18379-18386
Efficient Parahydrogen-Induced 13C Hyperpolarization on a Microfluidic Device
We show the direct production and detection of 13C-hyperpolarized fumarate by parahydrogen-induced polarization (PHIP) in a microfluidic lab-on-a-chip (LoC) device and achieve 8.5% 13C polarization. This is the first demonstration of 13C-hyperpolarization of a metabolite by PHIP in a microfluidic device. LoC technology allows the culture of mammalian cells in a highly controlled environment, providing an important tool for the life sciences. In-situ preparation of hyperpolarized metabolites greatly enhances the ability to quantify metabolic processes in such systems by microfluidic NMR. PHIP of 1H nuclei has been successfully implemented in microfluidic systems, with mass sensitivities in the range of pmol/s. However, metabolic NMR requires high-yield production of hyperpolarized metabolites with longer spin life times than is possible with 1H. This can be achieved by transfer of the polarization onto 13C nuclei, which exhibit much longer T1 relaxation times. We report an improved microfluidic PHIP device, optimized using a finite element model, that enables the direct and efficient production of 13C-hyperpolarized fumarate.
- 25 June 2024
- Published by American Chemical Society (ACS) in Journal of the American Chemical Society
- Vol. 146 (27) , 18379-18386
Open AccessEfficient Parahydrogen-Induced 13C Hyperpolarization on a Microfluidic Device
We show the direct production and detection of 13C-hyperpolarized fumarate by parahydrogen-induced polarization (PHIP) in a microfluidic lab-on-a-chip (LoC) device and achieve 8.5% 13C polarization. This is the first demonstration of 13C-hyperpolarization of a metabolite by PHIP in a microfluidic device. LoC technology allows the culture of mammalian cells in a highly controlled environment, providing an important tool for the life sciences. In-situ preparation of hyperpolarized metabolites greatly enhances the ability to quantify metabolic processes in such systems by microfluidic NMR. PHIP of 1H nuclei has been successfully implemented in microfluidic systems, with mass sensitivities in the range of pmol/s. However, metabolic NMR requires high-yield production of hyperpolarized metabolites with longer spin life times than is possible with 1H. This can be achieved by transfer of the polarization onto 13C nuclei, which exhibit much longer T1 relaxation times. We report an improved microfluidic PHIP device, optimized using a finite element model, that enables the direct and efficient production of 13C-hyperpolarized fumarate.
- Open Access
- 24 May 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Efficient Parahydrogen Induced 13C Hyperpolarization on a Microfluidic Device
We show the direct production and detection of 13C-hyperpolarized fumarate by parahydrogen-induced polarization (PHIP) in a microfluidic Lab-on-a-Chip (LoC) device and achieve 8.5% 13C polarization. This is the first demonstration of 13C-hyperpolarization of a metabolite by PHIP in a microfluidic device. LoC technology allows the culture of mammalian cells in a highly controlled environment, providing an important tool for the life sciences. In-situ preparation of hyperpolarized metabolites greatly enhances the ability to quantify metabolic processes in such systems by microfluidic NMR. PHIP of 1H nuclei has been successfully implemented in microfluidic systems, with mass sensitivities in the range of pmol √s. However, metabolic NMR requires high-yield production of hyperpolarized metabolites with longer spin life times than is possible with 1H. This can be achieved by transfer of the polarization onto 13C nuclei, which exhibit much longer T1 relaxation times. We report an improved microfluidic PHIP device, optimised using a finite element model, that enables the direct and efficient production of 13C hyperpolarized fumarate.
- 24 May 2024
- Published by American Chemical Society (ACS) in ChemRxiv
Open AccessEfficient Parahydrogen Induced 13C Hyperpolarization on a Microfluidic Device
We show the direct production and detection of 13C-hyperpolarized fumarate by parahydrogen-induced polarization (PHIP) in a microfluidic Lab-on-a-Chip (LoC) device and achieve 8.5% 13C polarization. This is the first demonstration of 13C-hyperpolarization of a metabolite by PHIP in a microfluidic device. LoC technology allows the culture of mammalian cells in a highly controlled environment, providing an important tool for the life sciences. In-situ preparation of hyperpolarized metabolites greatly enhances the ability to quantify metabolic processes in such systems by microfluidic NMR. PHIP of 1H nuclei has been successfully implemented in microfluidic systems, with mass sensitivities in the range of pmol √s. However, metabolic NMR requires high-yield production of hyperpolarized metabolites with longer spin life times than is possible with 1H. This can be achieved by transfer of the polarization onto 13C nuclei, which exhibit much longer T1 relaxation times. We report an improved microfluidic PHIP device, optimised using a finite element model, that enables the direct and efficient production of 13C hyperpolarized fumarate.
- Open Access
- 4 December 2023
- Published by American Chemical Society (ACS) in Analytical Chemistry
- Vol. 95 (49) , 17997-18005
Enzymatic Reactions Observed with Zero- and Low-Field Nuclear Magnetic Resonance
We demonstrate that enzyme-catalyzed reactions can be observed in zero- and low-field NMR experiments by combining recent advances in parahydrogen-based hyperpolarization methods with state-of-the-art magnetometry. Specifically, we investigated two model biological processes: the conversion of fumarate into malate, which is used in vivo as a marker of cell necrosis, and the conversion of pyruvate into lactate, which is the most widely studied metabolic process in hyperpolarization-enhanced imaging. In addition to this, we constructed a microfluidic zero-field NMR setup to perform experiments on microliter-scale samples of [1-13C]fumarate in a lab-on-a-chip device. Zero- to ultralow-field (ZULF) NMR has two key advantages over high-field NMR: the signals can pass through conductive materials (e.g., metals), and line broadening from sample heterogeneity is negligible. To date, the use of ZULF NMR for process monitoring has been limited to studying hydrogenation reactions. In this work, we demonstrate this emerging analytical technique for more general reaction monitoring and compare zero- vs low-field detection.
- 4 December 2023
- Published by American Chemical Society (ACS) in Analytical Chemistry
- Vol. 95 (49) , 17997-18005
Open AccessEnzymatic Reactions Observed with Zero- and Low-Field Nuclear Magnetic Resonance
We demonstrate that enzyme-catalyzed reactions can be observed in zero- and low-field NMR experiments by combining recent advances in parahydrogen-based hyperpolarization methods with state-of-the-art magnetometry. Specifically, we investigated two model biological processes: the conversion of fumarate into malate, which is used in vivo as a marker of cell necrosis, and the conversion of pyruvate into lactate, which is the most widely studied metabolic process in hyperpolarization-enhanced imaging. In addition to this, we constructed a microfluidic zero-field NMR setup to perform experiments on microliter-scale samples of [1-13C]fumarate in a lab-on-a-chip device. Zero- to ultralow-field (ZULF) NMR has two key advantages over high-field NMR: the signals can pass through conductive materials (e.g., metals), and line broadening from sample heterogeneity is negligible. To date, the use of ZULF NMR for process monitoring has been limited to studying hydrogenation reactions. In this work, we demonstrate this emerging analytical technique for more general reaction monitoring and compare zero- vs low-field detection.
- 7 September 2023
- Published by American Chemical Society (ACS) in Analytical Chemistry
- Vol. 95 (37) , 13932-13940
Development of Low-Magnetic Susceptibility Microcoils via 5-Axis Machining for Analysis of Biological and Environmental Samples
In environmental research, it is critical to understand how toxins impact invertebrate eggs and egg banks, which, due to their tiny size, are very challenging to study by conventional nuclear magnetic resonance (NMR) spectroscopy. Microcoil technology has been extensively utilized to enhance the mass-sensitivity of NMR. In a previous study, 5-axis computer numerical control (CNC) micromilling (shown to be a viable alternative to traditional microcoil production methods) was used to create a prototype copper slotted-tube resonator (STR). Despite the excellent limit of detection (LOD) of the resonator, the quality of the line shape was very poor due to the magnetic susceptibility of the copper resonator itself. This is best solved using magnetic susceptibility-matched materials. In this study, approaches are investigated that improve the susceptibility while retaining the versatility of coil milling. One method involves machining STRs from various copper/aluminum alloys, while the other involves machining ones from an aluminum 2011 alloy and electroplating them with copper. In all cases, combining copper and aluminum to produce resonators resulted in improved line shape and SNR compared to pure copper resonators due to their reduced magnetic susceptibility. However, the copper-plated aluminum resonators showed optimal performance from the devices tested. The enhanced LOD of these STRs allowed for the first H-1-C-13 heteronuclear multiple quantum coherence (HMQC) of a single intact C-13-labeled Daphnia magna egg (similar to 4 mu g total biomass). This is a key step toward future screening programs that aim to elucidate the toxic processes in aquatic eggs.
- 7 September 2023
- Published by American Chemical Society (ACS) in Analytical Chemistry
- Vol. 95 (37) , 13932-13940
Development of Low-Magnetic Susceptibility Microcoils via 5-Axis Machining for Analysis of Biological and Environmental Samples
In environmental research, it is critical to understand how toxins impact invertebrate eggs and egg banks, which, due to their tiny size, are very challenging to study by conventional nuclear magnetic resonance (NMR) spectroscopy. Microcoil technology has been extensively utilized to enhance the mass-sensitivity of NMR. In a previous study, 5-axis computer numerical control (CNC) micromilling (shown to be a viable alternative to traditional microcoil production methods) was used to create a prototype copper slotted-tube resonator (STR). Despite the excellent limit of detection (LOD) of the resonator, the quality of the line shape was very poor due to the magnetic susceptibility of the copper resonator itself. This is best solved using magnetic susceptibility-matched materials. In this study, approaches are investigated that improve the susceptibility while retaining the versatility of coil milling. One method involves machining STRs from various copper/aluminum alloys, while the other involves machining ones from an aluminum 2011 alloy and electroplating them with copper. In all cases, combining copper and aluminum to produce resonators resulted in improved line shape and SNR compared to pure copper resonators due to their reduced magnetic susceptibility. However, the copper-plated aluminum resonators showed optimal performance from the devices tested. The enhanced LOD of these STRs allowed for the first H-1-C-13 heteronuclear multiple quantum coherence (HMQC) of a single intact C-13-labeled Daphnia magna egg (similar to 4 mu g total biomass). This is a key step toward future screening programs that aim to elucidate the toxic processes in aquatic eggs.
- Open Access
- 21 February 2023
- Published by Elsevier in Journal of Magnetic Resonance
- Vol. 349, 107405
Operando NMR metabolomics of a microfluidic cell culture
- 21 February 2023
- Published by Elsevier in Journal of Magnetic Resonance
- Vol. 349, 107405
Open AccessOperando NMR metabolomics of a microfluidic cell culture