Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yuchun Li has a total of 22 co-authors. Here are the top co-authors by number of shared publications:

  • Qingshuang Di

    Senior Engineer, Earthquake Engineering Research Center, China Institute of Water Resources and Hydropower Research, Beijing 100038, China; Ph.D. Student, Dept. of Hydraulic Engineering, Tongji Univ., Shanghai 200092, China

    3 shared publications
  • Zhuang Wang

    Research Institute of Structural Engineering and Disaster Reduction, Tongji University, Shanghai, China

    3 shared publications
  • Chao Shen

    Department of Hydraulic Engineering, College of Civil Engineering, Tongji University, Shanghai, China

    2 shared publications
  • Bin Zhang

    Shanghai Polytech Univ, Sch Energy & Mat, Shanghai 201209, Peoples R China

    1 shared publication
  • Changhao Wei

    Shaanxi Key Laboratory of Safety and Durability of Concrete Structures, Xijing University, Xi’an 710123, China

    1 shared publication
  • Chao Shen

    Department of Hydraulic Engineering, College of Civil Engineering, Tongji University, Shanghai 200092, China

    1 shared publication

Latest Publications

  • Open Access

    Experimental and Finite Element Study on the Seismic Performance of Reinforced New-Type Joints: Adding Beams to Existing Columns

    by Jian Wu, Shi’En Zhang, Changhao Wei, Yifei Tao, Chunjuan Zhou, Yuxi Wang, Yuchun Li

    Currently, the development of civil engineering industry is gradually slowing down, with the focus gradually shifting toward the reinforcement and renovation of existing buildings. Among these existing structures, reinforced concrete (RC) structure is a kind of structure with high proportion. Therefore, this paper conducts research on the seismic properties of RC buildings after adding new beams to existing columns. This paper first introduces the design situation of the specimen, followed by an experimental investigation of its mechanical properties using pseudo-static tests. Based on the failure patterns and hysteresis curves, the differences between the new-type specimen and RC specimen are analyzed. The findings indicate that, while ensuring load-bearing capacity, the new-type joints exhibit better seismic performance: the bearing capacity and maximum displacement are increased by at most 9.2% and 14.9% respectively, and the fuller hysteresis curve shows that the new-type specimen has better energy dissipation capacity. Finally, this paper extends the analysis of the design parameters of the specimens using finite element components. The modeling results reveal that the bearing capacity varies by less than 1% with different parameters such as connector thickness, concrete strength grade, and bolts quantity and strength, indicating that these parameters have a relatively small impact on the bearing capacity. While for the specimen dimensions and thickness and strength of wrapped steel of beam, the maximum increase in bearing capacity is 32.3% and 6.0%, respectively. Indicating that their impact is quite significant. The findings of this paper provide a reference for structural design and contribute to advancing the work of reinforcement and renovation of existing concrete structures.

  • Open Access

    A Nonlinear Parametric Resonance Analysis of Planar Beam Structures Using Vector Form Intrinsic Finite Element Method

    by Yuchun Li, Chao Shen, Zhang Que

    The parametric resonance of a frame structure may lead to a disastrous consequence. Structural engineers need a straightforward and practical method to calculate the large nonlinear parametric resonance responses of the frame structure for assessing structural safety. This paper reports on a new Vector Form Intrinsic Finite Element (VFIFE) method to analyse the nonlinear parametric resonance of planar beam structures. By taking into account the geometric stiffness effect of the internal axial force for the frame element, a relationship between internal nodal forces and deformation components is firstly established based on the VFIFE principle and the parametric resonance mechanism of frame structures. The VFIFE scheme is then developed to analyse the nonlinear parametric resonance of frame structures. To demonstrate the efficacy of this approach, a simply-supported beam is used as a numerical example, and the resulting VFIFE calculations are compared to the solutions obtained by current analytical methods. A parametric resonance test of the cantilever beam is conducted to verify the applicability of the VFIFE method. The numerical results show that this approach can overcome the limitations of existing analytical methods, well simulate the nonlinear phenomena of parametric resonances, and produce predictions that are consistent with experimental observations. The numerical stability boundary of parametric resonance agrees well with the experimental boundary. Possible causes of deviations between the numerical and experimental results are discussed. The proposed VFIFE method is a simple and effective means of analyzing the stability and nonlinear responses of parametric resonance of planar beam structures.


  • Auto-parametric sloshing in a rectangular aqueduct excited by wind vortex-induced vibration: experimental investigation and stability analysis

    by Yuchun Li, Lishi Wang, Chao Shen

    The vortex-induced vibration of the aqueduct girder may excite the parametric sloshing of the contained water which will have substantial impacts on the normal running and structural safety of the aqueduct bridge. This paper first conducts a wind-tunnel experiment to investigate the auto-parametric sloshing caused by wind vortex-induced vibration for an elastically-hung rectangular aqueduct with contained water. When the vortex excitation frequency is close to the natural frequency of the structure and approximately equal to twice the natural frequency of the fluid the vortex-induced resonance of the structure and the strong auto-parametric sloshing (internal resonance) of water successively occur in the test. The auto-parametric sloshing for the non-internal resonance case is also experimentally investigated. The contained water can be simplified as a rigid mass for the stability analysis of sloshing. The instability boundaries of sloshing and the corresponding wind speed regions are theoretically determined and compared with the experimental results


  • Open Access

    Modeling Problem of Equivalent Mechanical Models of a Sloshing Fluid

    by Yu-Chun Li, Hong-Liang Gou

    Because the defects in the existing modeling methods for the equivalent mechanical model of a sloshing fluid have led to incorrect or inaccurate results in the existing equivalent models, this paper discusses three different modeling methods for the equivalent models: the traditional method, Housner’s method, and the modified method. The equivalent models obtained by the three methods are, respectively, presented and compared with each other for a liquid in rectangular and upright cylindrical tanks. The results show that the traditional method cannot provide the correct location expressions of the equivalent masses because the two types of different excitations are simultaneously used in one equivalent model. An equivalent model is exclusively applicable to a certain excitation (a translational excitation in a certain direction or a rotational excitation about a certain axis). Housner’s method is based on physical intuition, instead of fluid dynamics theory, therefore the calculation precision of Housner’s solution is not satisfactory. Housner’s method is only suitable for vertical tanks with a flat bottom subjected to a horizontal excitation. Based on a conceptual mistake in the traditional method, the concept of the equivalent model is reclarified, and the modified equivalence method is therefore suggested. A supplementary solution for the equivalent model in a cylindrical tank is presented. The correct models can be acquired using the modified equivalence method, which is applicable to tanks of arbitrary shape.


  • Modal Analysis of the Saint-Bachi Suspension Aqueduct Bridge Considering Fluid–Structure Interaction

    by Qingshuang Di, Yuchun Li, Yichuan Xing, Xiao Hu

    The aim of this paper is to reveal the unique dynamic characteristics of the Saint-Bachi suspension pipeline bridge with fluid–structure interaction. With commercial software, a three-dimensional finite-element (FE) model of this bridge is developed to simulate its dynamic properties. The solid and fluid elements are, respectively, applied to model the structural members (pipe girder, cables, and portal frames) of the bridge and the water in the pipe girder. The dry (without fluid) and wet (with fluid) modes of the suspension pipeline bridge are, respectively, calculated and compared. The dry modes are fundamentally the same as those of the ordinary highway suspension bridges. The number of wet modes has been greatly increased due to the interaction between sloshing water and structure. According to the oscillation phases of sloshing fluid and pipe girder, the wet modes can be divided into the in-phase, out-of-phase, and no-sloshing modes. The in-phase and out-of-phase modes represent the synchronous and unsynchronous motions of pipe girder and fluid, respectively. The no-sloshing mode denotes a pure girder bending vibration without water sloshing. The in-phase (synchronous) frequencies are decreased with increased fluid depth. The out-of-phase (unsynchronous) frequencies might be increased or decreased with increased fluid depth. The (local) wet frequencies of pylons and cables may increase with the increment of water depth due to increased tension force of the cables.


  • Unstable characteristics of two-dimensional parametric sloshing in various shape tanks: theoretical and experimental analyses

    by Yuchun Li, Zhuang Wang

    The equations of two-dimensional parametric sloshing are derived for a fluid in an arbitrary shape tank. The parametric instability of the liquid free surface is reduced to the Mathieu equation. An energy-growth exponent λ (EGE) and the corresponding non-dimensional energy-growth coefficient (EGC) η are defined for measuring the instability intensity and determining the stability boundaries of the parametrically-excited fluid system. A stability criterion is proposed by using the EGE. On the basis of the numerical tests, the analytical expressions of EGE/EGC are developed for the fluid system that is governed by the Mathieu equation. Under the small excitations, the stability boundaries by using EGE/EGC agree well with those by the traditional theory. The unstable properties, including instability intensity, instability boundaries and competition of unstable patterns etc, of parametric sloshing are analyzed and discussed in details with EGE/EGC for the fluid system. The fluid system always selects such an unstable pattern that possesses a larger energy-growth exponent. A two-dimensional parametric sloshing experiment is respectively conducted for the fluid in the rectangular, circular and U-shaped tanks. The theoretical and experimental stability boundaries of the principal parametric sloshing are obtained and compared for the fluid in three different shape tanks. Some theoretical predictions of the unstable properties of parametric sloshing are verified through the experiment.


  • Open Access

    An Approximate Analytical Solution of Sloshing Frequencies for a Liquid in Various Shape Aqueducts

    by Yuchun Li, Zhuang Wang

    An approximate analytical solution of sloshing frequencies for a liquid in the various shape aqueducts is formulated by using the Ritz method. The present approximate method is, respectively, applied to find the sloshing frequencies of the liquid in rectangular, trapezoid, oval, circular, U-shaped tanks (aqueducts), and various shape tuned liquid dampers (TLD). The first three antisymmetric and symmetric frequencies by the present approach are within 5% accuracy compared to the other analytical, numerical, and experimental values. The approximate solutions of this paper for the various shape aqueducts are acceptable to the engineering applications.