Xiaodong Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiaodong Li has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Han Dong
State Key Laboratory of Advanced Special Steel and Shanghai Key Laboratory of Advanced Ferrometallurgy, School of Materials Science and Engineering, Shanghai University, Shanghai, China
3 shared publicationsYing Chang
School of Automotive Engineering, Dalian University of Technology, Dalian, China
3 shared publications- Ying Chang
School of Materials Science and Engineering, Dalian University of Technology, Dalian, China
3 shared publications Cunyu Wang
Central Iron & Steel Research Institute (CISRI), Beijing, China
2 shared publications- Chunlin Li
State Key Laboratory of Metallic Materials for Marine Equipment and Applications, Anshan 114009, China
1 shared publication Chunning Jin
School of Automotive Engineering, Dalian University of Technology, Dalian, China
1 shared publication
Latest Publications
- Open Access
Hot-Formed, High-Strength, Integrated Automotive Parts: Numerical Analysis and Process Optimization
Hot-forming, as a typical representative forming technology of high-strength steel (HSS), is one of the most effective ways to manufacture structural components for achieving automotive lightweighting goal. In this paper, a newly-developed commercial microalloyed hot-formed steel is selected and its hot-forming is studied by experiments and simulations. The new steel has a wide undercooled austenite region, providing more suitable condition for the manufacturing of one-piece large-sized integrated parts. The high-temperature mechanical behaviors of the investigated steel show that the flow stress obviously decreases with the increase in deformation temperature, and it increases with the increasing strain rate. An integrated component assembly of the rear floor and longitudinal beam is selected as a typical one-piece integrated part when performing the hot-forming simulation to evaluate the formability. The influences of the key process parameters, namely forming velocity and frictional coefficient, on formability are further analyzed. Finally, the Latin Hypercube Sampling (LHS) method is used to generate the parameter combination and the Response Surface Method (RSM) is adopted in optimization. As a result, an optimal process parameter combination is obtained and its predicted result matches the simulated one very well, with a relative error of only 2.57%. The research results of this paper are favorable for understanding the mechanical behaviors of the hot-formed steel at elevated temperatures, improving the formability and providing a reference for the development of large-sized integrated hot-formed parts.
Open AccessHot-Formed, High-Strength, Integrated Automotive Parts: Numerical Analysis and Process Optimization
Hot-forming, as a typical representative forming technology of high-strength steel (HSS), is one of the most effective ways to manufacture structural components for achieving automotive lightweighting goal. In this paper, a newly-developed commercial microalloyed hot-formed steel is selected and its hot-forming is studied by experiments and simulations. The new steel has a wide undercooled austenite region, providing more suitable condition for the manufacturing of one-piece large-sized integrated parts. The high-temperature mechanical behaviors of the investigated steel show that the flow stress obviously decreases with the increase in deformation temperature, and it increases with the increasing strain rate. An integrated component assembly of the rear floor and longitudinal beam is selected as a typical one-piece integrated part when performing the hot-forming simulation to evaluate the formability. The influences of the key process parameters, namely forming velocity and frictional coefficient, on formability are further analyzed. Finally, the Latin Hypercube Sampling (LHS) method is used to generate the parameter combination and the Response Surface Method (RSM) is adopted in optimization. As a result, an optimal process parameter combination is obtained and its predicted result matches the simulated one very well, with a relative error of only 2.57%. The research results of this paper are favorable for understanding the mechanical behaviors of the hot-formed steel at elevated temperatures, improving the formability and providing a reference for the development of large-sized integrated hot-formed parts.
- Open Access
Fracture Behavior of the Hot-Stamped PHS2000 Steel Based on GISSMO Failure Model
Hot-stamped steel is currently the most widely used lightweight material in automobiles, and accurately predicting its failure risk during the simulation is a bottleneck problem in the automobile industry. In this study, the fracture failure behavior of the hot-stamped PHS2000 steel manufactured by Ben Gang Group (Benxi, China) is investigated by experiments and simulation. Static tension and high-speed tension tests are conducted to obtain the elastic-plastic stress-strain relations, and a Swift + Hockett–Sherby model is proposed to describe the hardening behavior under static and high-speed loads. Tests under five kinds of stress states, namely static shear, static tensile shear, notched static tension, center-hole static tension, and static punching, are conducted to obtain the ultimate fracture strains under different stress states for establishing a failure model. The finite element method (FEM) is used to inversely achieve the fracture parameters of the material, and the GISSMO model in LS-Dyna is adopted to describe the fracture characteristics of the material. A fracture card is further established for simulation analysis by combining fracture characteristics with high-speed tension curves and simultaneously loading size effect curves of meshes. Finally, the card is applied in the simulation of the three-point bending test. High-precision results of fracture simulation matching the experimental results are obtained. This research proves that the proposed fracture card is accurate and can be widely used in the simulation of fracture behaviors of the hot-stamped PHS2000 steel.
Open AccessFracture Behavior of the Hot-Stamped PHS2000 Steel Based on GISSMO Failure Model
Hot-stamped steel is currently the most widely used lightweight material in automobiles, and accurately predicting its failure risk during the simulation is a bottleneck problem in the automobile industry. In this study, the fracture failure behavior of the hot-stamped PHS2000 steel manufactured by Ben Gang Group (Benxi, China) is investigated by experiments and simulation. Static tension and high-speed tension tests are conducted to obtain the elastic-plastic stress-strain relations, and a Swift + Hockett–Sherby model is proposed to describe the hardening behavior under static and high-speed loads. Tests under five kinds of stress states, namely static shear, static tensile shear, notched static tension, center-hole static tension, and static punching, are conducted to obtain the ultimate fracture strains under different stress states for establishing a failure model. The finite element method (FEM) is used to inversely achieve the fracture parameters of the material, and the GISSMO model in LS-Dyna is adopted to describe the fracture characteristics of the material. A fracture card is further established for simulation analysis by combining fracture characteristics with high-speed tension curves and simultaneously loading size effect curves of meshes. Finally, the card is applied in the simulation of the three-point bending test. High-precision results of fracture simulation matching the experimental results are obtained. This research proves that the proposed fracture card is accurate and can be widely used in the simulation of fracture behaviors of the hot-stamped PHS2000 steel.
- Open Access
Influence of Cutting Process on the Flanging Formability of the Cut Edge for DP980 Steel
Flanging is a key process in the forming of automobile parts and is influenced by the cutting process before it. In this paper, a set of self-designed tools is adopted. The flanging height and flanging radius are specified as the indexes to investigate the influence of the cutting process on the flanging formability of DP980 steel. Microstructure, microhardness, and tensile properties are tested to evaluate the formability of cut edges. The results show that the flanging formability is positively correlated with an increase in flanging height and a decrease in flanging radius. The flanging formability of six cut edges can be ranked as: LC-L > LC-H > WEDM-HS > WEDM-LS > CNC milling > WJC. In the LC process, acicular martensite is formed and the microhardness of the cut edge significantly increases, with a heat-affected zone of about 150 μm. More and larger microvoids are found on the edge of WEDM-LS than WEDM-HS, which reduces the formability to a certain extent. Plastic deformation of the edges is the reason for the decrease in the formability of CNC milling. For WJC, the formation of irregular edge damage and the generation of burrs are the main reasons for the unstable performance. This research is helpful in guiding the selection of the cutting process, and it may contribute to a high part formability for DP980 steel.
Open AccessInfluence of Cutting Process on the Flanging Formability of the Cut Edge for DP980 Steel
Flanging is a key process in the forming of automobile parts and is influenced by the cutting process before it. In this paper, a set of self-designed tools is adopted. The flanging height and flanging radius are specified as the indexes to investigate the influence of the cutting process on the flanging formability of DP980 steel. Microstructure, microhardness, and tensile properties are tested to evaluate the formability of cut edges. The results show that the flanging formability is positively correlated with an increase in flanging height and a decrease in flanging radius. The flanging formability of six cut edges can be ranked as: LC-L > LC-H > WEDM-HS > WEDM-LS > CNC milling > WJC. In the LC process, acicular martensite is formed and the microhardness of the cut edge significantly increases, with a heat-affected zone of about 150 μm. More and larger microvoids are found on the edge of WEDM-LS than WEDM-HS, which reduces the formability to a certain extent. Plastic deformation of the edges is the reason for the decrease in the formability of CNC milling. For WJC, the formation of irregular edge damage and the generation of burrs are the main reasons for the unstable performance. This research is helpful in guiding the selection of the cutting process, and it may contribute to a high part formability for DP980 steel.
- 4 August 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 117 (3-4) , 1015-1027
Evaluation on the formability of the third-generation automotive medium-Mn steel based on experiment and simulation
- 4 August 2021
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 117 (3-4) , 1015-1027
Evaluation on the formability of the third-generation automotive medium-Mn steel based on experiment and simulation
- 1 January 2017
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 53 (8) , 35-42
Research on the Warm-hot Forming Process and Its Performance Evaluation for the Third-generation Automobile Steel
- 1 January 2017
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 53 (8) , 35-42
Research on the Warm-hot Forming Process and Its Performance Evaluation for the Third-generation Automobile Steel
- 28 March 2016
- Published by Springer Nature in Science China Technological Sciences
- Vol. 59 (5) , 832-838
Relation of martensite-retained austenite and its effect on microstructure and mechanical properties of the quenched and partitioned steels
- 28 March 2016
- Published by Springer Nature in Science China Technological Sciences
- Vol. 59 (5) , 832-838
Relation of martensite-retained austenite and its effect on microstructure and mechanical properties of the quenched and partitioned steels
- 22 January 2016
- Published by Elsevier in Applied Thermal Engineering
- Vol. 99, 419-428
Effect of contact pressure on IHTC and the formability of hot-formed 22MnB5 automotive parts
- 22 January 2016
- Published by Elsevier in Applied Thermal Engineering
- Vol. 99, 419-428
Effect of contact pressure on IHTC and the formability of hot-formed 22MnB5 automotive parts
- 20 June 2015
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 24 (8) , 3194-3200
Effect of Quenching and Partitioning with Hot Stamping on Martensite Transformation and Mechanical Properties of AHSS
- 20 June 2015
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 24 (8) , 3194-3200
Effect of Quenching and Partitioning with Hot Stamping on Martensite Transformation and Mechanical Properties of AHSS
- 1 May 2014
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 21 (5) , 517-520
Preparation of Nanoscale Sm2Co17 Flakes by Ball Milling in Magnetic Field
- 1 May 2014
- Published by Springer Nature in Journal of Iron and Steel Research International
- Vol. 21 (5) , 517-520
Preparation of Nanoscale Sm2Co17 Flakes by Ball Milling in Magnetic Field