TTTakahiro Tomioka

Takahiro Tomioka

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Takahiro Tomioka has a total of 76 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • オイラー角で質量の支持角度を指定する多軸動吸振器のためのばね要素の検討

    by Kyosuke Sato, Takahiro Tomioka

    The authors have been studying a multi-mode damping device consisting of a mass supported from multiple directions by eight springs, and the mass can vibrate in multi-directions. By this configuration, the device can show multi-axial vibration damping ability, so it can be called a multi-axial dynamic vibration absorber (DVA). A theory to specify the natural frequency in the x, y, and z directions fx, fy, and fz by the supporting angle of the mass has been reported in the former studies by the authors. However, some large differences were observed between experimental and theoretical results in the past studies. These disagreements are considered due to friction between the spring and supporting frame and/or the unexpected deformation of the springs. Therefore, a supporting frame to hold the springs without guides is designed in this study. We also focus on the shape of the supporting springs, and conical springs and short-length coil springs are employed. Some multi-axial DVA using the frame or springs are developed actually, and vibration measurement tests to check the natural frequency in every direction are conducted. This paper describes those experiments and discusses the obtained results.

  • 鉄道車両の実走行模擬加振による弾性トーラスの車体弾性振動低減効果の検証

    by Ken-Ichiro Aida, Yuki Akiyama, Takahiro Tomioka

    We have been developing an elastic torus filled with water or super absorbent polymer (SAP) as one of the methods for reducing car-body elastic vibrations. This device, which is inspired by vibration reduction effect by passengers, is a kind of dynamic vibration absorber utilizing elastic deformation of an elastic body. We carried out excitation tests using a Shinkansen type test vehicle in a rolling stock testing plant to examine the effect of reducing car-body vibrations. The results showed that two dominant peaks around 10Hz in the acceleration power spectrum densities of the floor corresponding to elastic vibration modes were reduced simultaneously when the elastic tori were loaded on the vehicle. The peak values decreased according to the increase of the number of elastic tori. And it has found that the ride comfort can be improved.

  • Numerical Investigation for Realization of Lightweight, High-rigidity and High Damping Performance Metal Laminated Materials

    by Yuki Sasage, Takahiro Tomioka, Hisashi Hori

    Laminated metals consisting of different metallic materials are expected to have advantages over single metal materials; high damping capability is one such additional value. This report describes a numerical approach for evaluating the damping capability of laminated metals. For this purpose, we employed the classical lamination theory, which is widely applied to FRPs or damping steels with viscoelastic layers, in this study. The modal characteristics (natural frequencies and natural mode shapes), specific damping capacity and modal loss factor, and frequency response functions (FRFs) against excitation input for laminated metal beams are calculated using the proposed method. Those results are compared with those using a finite element (FE) analysis and experiments, and the validity of the proposed method has been confirmed. Numerical studies are conducted to search for highly advantageous configurations of two metals (aluminum and copper) in terms of lightweight, high stiffness, and high damping performance.

  • Open Access

    Numerical study on the effect by the structural characteristics of carbody shell faces on elastic vibrations of railway vehicle carbodies

    by Shizuya Yamaguchi, Takahiro Tomioka

    Three-dimensional (3D) elastic vibrations in railway vehicle carbodies sometimes negatively impact ride comfort, and efficient numerical analysis methods are required to study effective countermeasures. The authors proposed in their former work a new vibration analysis model in which the railway vehicle carbody is modeled as a box-like structure composed of elastic plates, straight beams, and curved beams. This model can easily express complex 3D vibration shapes observed in actual carbody, such as the interaction between the roof, floor, and side structures. In this paper, an improved version of the previous model is proposed, firstly. Then, a series of numerical studies are carried out by changing the structural properties of each face of the carbody shell, including cross-sectional shapes or bending rigidities, to investigate their effect on the natural frequencies. According to the numerical results, it has been shown that the side pillars primarily affect the modes with cross-sectional deformation of the carbody. Additionally, as a general tendency, the bending and shear rigidities of the roof panel have been found to have a relatively significant effect on the first bending and the diagonal distortion modes.


  • Open Access

    Multimodal Reduction of Elastic Vibrations in Plate Structure using Super Absorbent Polymer Beads

    by Takahiro Tomioka, Karen Minamisawa

    This paper deals with multimodal reduction of structural elastic vibrations. Super absorbent polymer beads (SAP beads) have been introduced as a simple damping device inspired by the multimodal vibration reduction effect by passengers on railway vehicles. A series of vibration measurement tests using a 1:10 scale model of railway vehicle floor structure (model underframe) was carried out. The SAP beads which are sold commonly as water retention agent were stacked in a container and applied to the model underframe. From the experiments, multimodal vibration reduction effects have been demonstrated. A drastic difference has been observed when water was added together with SAP beads. To investigate the basic mechanism of the damping effect obtained by the experiments, an analytical model, which consists of multiple masses that are supported at an angle to each other, and its simplified model was proposed and numerical studies were conducted. Some specific combinations of the mass, spring, and damping elements in the model could express the experimental results well, and it has been estimated from the numerical results that each SAP layer act as an un-uniform subsystem.


  • A three-dimensional analytical model and parameter determination method of the elastic vibration of a railway vehicle carbody

    by Yuki Akiyama, Takahiro Tomioka, Tadao Takigami, Ken-Ichiro Aida, Takayoshi Kamada

    Reducing railway vehicles’ three-dimensional (3D) elastic vibration is needed to improve passenger comfort. This paper presents a 3D analytical model and parameter determination method for the elastic vibration of a carbody. The carbody is modelled as a simple box-type structure consisting of an anisotropic 3D elastic body treated as a continuous system. This model can express complicated 3D elastic vibration (such as lateral–vertical coupled vibration) with fewer degrees of freedom and at a lower computational cost than the detailed finite element model. A model parameter determination method using particle swarm optimisation was also proposed. Application to a Shinkansen-type test vehicle showed good agreement between measured and calculated results with a maximum natural frequency differences of the targeted six elastic vibration modes within 0.86%, indicating the effectiveness of the proposed model and parameter determination method.


  • Damping effect of multi-directional resiliently supported mass for railway vehicle carbodies (Excitation tests and FEM analysis for a scale model using a concept model)

    by Yasunobu Makita, Yuki Akiyama, Tadao Takigami, Takahiro Tomioka

    It has been shown that passengers have large reduction effect on the elastic vibration of a railway vehicle car body. That effect is considered due to the viscoelastic motion and multi-directional motion of a human body. This study focuses on the latter one and aims to develop a new vibration reduction device to mimic the multi-directional motion of passengers. In this paper, an experimented multi-directional dynamic vibration absorber (called MDDVA in this report) is developed. The MDDVA consists of a steel ball supported resiliently by elastic balls bottled in a rigid cylindrical vessel. The steel ball can vibrate multi-directionally in the vessel and is expected to work as a MDDVA. In addition, the natural frequency of the MDDVA can be changed by pressing the elastic balls from the top. To evaluate the effectiveness of the MDDVA, excitation tests by means of a scale model of a railway vehicle is conducted. As a result, the MDDVA can reduce the elastic vibration by adjusting the natural frequency of MDDVA to that of the scale model, and multi-modal vibration reduction effect is successfully observed. And then, FEM models of the MDDVA and a scale model of the railway vehicle are constructed to verify the mechanism of the multi-modal vibration reduction. As a result of the FEM analysis, it is confirmed that the multi-directional motion of the steel ball produces the multi-modal vibration reduction effect.

  • Experimental investigations on the damping effect due to passengers on flexural vibrations of railway vehicle carbody and basic studies on the mimicry of the effect with simple substitutions

    by T. Tomioka, T. Takigami, K. Aida

    The effect of passengers on a railway vehicle is usually considered as additional mass in designing a carbody. However, previous studies by means of stationary excitation tests or running tests using actual vehicles indicate that passengers behave not as mass but as damping. In this paper, the authors examined the passengers' damping effect under controlled excitation conditions on a roller rig through a series of excitation tests using a commuter-type vehicle. Large and multi-modal reductions of flexural vibrations of the carbody were observed when passengers existed. Influences of the number of passengers, distributions and postures of passengers were investigated. The authors also tried to mimic the damping effect by passengers using flexible tanks filled with fluids. Three kinds of fluids which have different viscosities have been tested. As a result of the excitation tests, good vibration reduction effects were observed by applying those tanks, and it has been found that the flexible tanks filled with fluids bring about vibration reduction effect (including multi-modal reduction) which is equal to or rather better than the case of similar mass of passengers in the carbody; the difference of viscosity gave little affect on the damping abilities. From these measurement results, a possibility of realising effective damping devices against flexural vibrations of railway vehicle carbodies representing passengers damping effect, in a simple, economical and environmental friendly way, has been demonstrated.