Ali Ajami
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ali Ajami has a total of 88 co-authors. Here are the top co-authors by number of shared publications:
- Ataollah Mokhberdoran
Department of Electrical and Computer Engineering, University of Porto, Porto, Portugal
8 shared publications Hossein Ardi
Electrical Engineering Department Azarbaijan Shahid Madani University Tabriz, East Azerbaijan Iran
8 shared publications- Mohammad Reza Jannati Oskuee
Young Researchers and elite Club, Tabriz Branch, Islamic Azad University, Tabriz, Iran
7 shared publications S.H. Hosseini
Electrical and Computer Engineering Faculty, Tabriz University, Tabriz, Iran
5 shared publicationsMehdi Armaghan
Islamic Azad Univ, Ardabil Branch, Young Researchers Club, Ardebil, Iran
4 shared publications- Amin Mohammadpour Shotorbani
Faculty of Electrical and Computer Engineering University of Tabriz Tabriz Iran
3 shared publications
Latest Publications
- 1 June 2026
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 39 (2) , 1157-1175
A Common Ground Non-Isolated Bidirectional DC-DC Converter with Low Stress and High Conversion ratio for Utilization in DC Micro-Grids
With the increasing integration of renewable energy sources and energy storage systems in DC micro-grids, there is a growing demand for bidirectional DC–DC converters that combine high efficiency, wide voltage conversion capability, and simple control structures. A non-isolated bidirectional DC–DC topology is introduced in this study, suitable for micro-grid utilizations, aiming to establish a common ground. The converter comprises four primary switches, supplemented by four capacitors and three inductors. Its straightforward configuration, high voltage gain conversion ratio, minimal voltage stress on switches, and common ground connectivity constitute key advantages. Additionally, the converter offers good step-up/step-down voltage conversion ratio, e.g. output voltage four times higher(lower) for step-up (step-down) mode with a fifty percent duty cycle. With its simple architecture and having only two modes in each switching period for both step-up and step-down operation states, the control for this topology becomes streamlined. The paper conducts a comprehensive analysis encompassing steady-state considerations in both operational directions, assessment of voltage stress on switches, and juxtaposition with alternative bidirectional converters. To prove the presented theoretical analyses, a 200 W laboratory model of the circuit is constructed and evaluated. The efficiency of the introduced circuit at nominal power is 92 percent.
- 1 June 2026
- Published by Gazi University Journal of Science in Gazi University Journal of Science
- Vol. 39 (2) , 1157-1175
A Common Ground Non-Isolated Bidirectional DC-DC Converter with Low Stress and High Conversion ratio for Utilization in DC Micro-Grids
With the increasing integration of renewable energy sources and energy storage systems in DC micro-grids, there is a growing demand for bidirectional DC–DC converters that combine high efficiency, wide voltage conversion capability, and simple control structures. A non-isolated bidirectional DC–DC topology is introduced in this study, suitable for micro-grid utilizations, aiming to establish a common ground. The converter comprises four primary switches, supplemented by four capacitors and three inductors. Its straightforward configuration, high voltage gain conversion ratio, minimal voltage stress on switches, and common ground connectivity constitute key advantages. Additionally, the converter offers good step-up/step-down voltage conversion ratio, e.g. output voltage four times higher(lower) for step-up (step-down) mode with a fifty percent duty cycle. With its simple architecture and having only two modes in each switching period for both step-up and step-down operation states, the control for this topology becomes streamlined. The paper conducts a comprehensive analysis encompassing steady-state considerations in both operational directions, assessment of voltage stress on switches, and juxtaposition with alternative bidirectional converters. To prove the presented theoretical analyses, a 200 W laboratory model of the circuit is constructed and evaluated. The efficiency of the introduced circuit at nominal power is 92 percent.
- Open Access
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 19 (1)
Coupled Inductor Based Quadratic High‐Gain DC‐DC Converter With Wide Range of CCM Operation for Photovoltaic Applications
This paper presents a novel DC‐DC converter designed to achieve a high step‐up voltage gain while maintaining a continuous input current. By incorporating a coupled inductor, the proposed converter achieves a high voltage conversion ratio. The continuous input current with minimal ripple makes this converter particularly suitable for a wide range of applications, especially in photovoltaic (PV) systems. The converter operates in continuous conduction mode (CCM) across a wide range of output loads, input voltages, and duty cycles. The use of a single power switch and gate driver circuit not only reduces costs but also enhances overall efficiency. The paper provides a detailed steady‐state mathematical analysis of the converter and examines its operation in CCM, discontinuous conduction mode (DCM), and boundary condition mode (BCM). Additionally, an efficiency analysis is presented. To validate the converter's performance, experimental results are provided for a prototype with an input voltage of 20 V, an output voltage of 400 V, an output power of 235 W, and a switching frequency of 33 kHz. These results are thoroughly analysed to confirm the converter's effectiveness. Finally, the proposed topology is compared with other existing topologies to further evaluate its performance. For instance, at a duty cycle (D) of 0.5, the converter achieves a voltage gain of 20, demonstrating its superior step‐up capability.
- 1 January 2025
- Published by Institution of Engineering and Technology (IET) in IET Renewable Power Generation
- Vol. 19 (1)
Open AccessCoupled Inductor Based Quadratic High‐Gain DC‐DC Converter With Wide Range of CCM Operation for Photovoltaic Applications
This paper presents a novel DC‐DC converter designed to achieve a high step‐up voltage gain while maintaining a continuous input current. By incorporating a coupled inductor, the proposed converter achieves a high voltage conversion ratio. The continuous input current with minimal ripple makes this converter particularly suitable for a wide range of applications, especially in photovoltaic (PV) systems. The converter operates in continuous conduction mode (CCM) across a wide range of output loads, input voltages, and duty cycles. The use of a single power switch and gate driver circuit not only reduces costs but also enhances overall efficiency. The paper provides a detailed steady‐state mathematical analysis of the converter and examines its operation in CCM, discontinuous conduction mode (DCM), and boundary condition mode (BCM). Additionally, an efficiency analysis is presented. To validate the converter's performance, experimental results are provided for a prototype with an input voltage of 20 V, an output voltage of 400 V, an output power of 235 W, and a switching frequency of 33 kHz. These results are thoroughly analysed to confirm the converter's effectiveness. Finally, the proposed topology is compared with other existing topologies to further evaluate its performance. For instance, at a duty cycle (D) of 0.5, the converter achieves a voltage gain of 20, demonstrating its superior step‐up capability.
- Open Access
- 14 October 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (15) , 2531-2548
Design and implementation of a solar power optimizer for module level power electronics application
Partial shading on series‐connected photovoltaic (PV) panels in conventional PV systems results in lower harvested power. To resolve this, it is vital to utilize module level power electronics (MLPE) such as Solar Power Optimizers (SPOs). This paper introduced a non‐isolated common ground non‐inverting output voltage buck‐boost converter as an SPO. Proposed converter benefits from continuous input and output currents which has a significant role in designing SPOs. Having a quadratic gain, beside acceptable step‐down range are other features of the converter. Operating principle, design, steady‐state, small‐signal analysis, and dynamic performance of proposed converter are included. Proposed converter is compared with other buck‐boost converters in terms of voltage gain, voltage stresses, continuous input and output current, and output polarity. To validate the performance of introduced converter, experimental results for a prototype with input voltage 24 V, output voltage 72 V for step‐up and 15 V for step‐down modes are given and results are examined. The maximum efficiency of the prototype is 93% and 89% for step‐up and step‐down modes, respectively. To evaluate the effect of proposed SPO for extracting maximum available power from PVs, simulation results of a grid connected PV system with two series connected SPOs is discussed.
- 14 October 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (15) , 2531-2548
Open AccessDesign and implementation of a solar power optimizer for module level power electronics application
Partial shading on series‐connected photovoltaic (PV) panels in conventional PV systems results in lower harvested power. To resolve this, it is vital to utilize module level power electronics (MLPE) such as Solar Power Optimizers (SPOs). This paper introduced a non‐isolated common ground non‐inverting output voltage buck‐boost converter as an SPO. Proposed converter benefits from continuous input and output currents which has a significant role in designing SPOs. Having a quadratic gain, beside acceptable step‐down range are other features of the converter. Operating principle, design, steady‐state, small‐signal analysis, and dynamic performance of proposed converter are included. Proposed converter is compared with other buck‐boost converters in terms of voltage gain, voltage stresses, continuous input and output current, and output polarity. To validate the performance of introduced converter, experimental results for a prototype with input voltage 24 V, output voltage 72 V for step‐up and 15 V for step‐down modes are given and results are examined. The maximum efficiency of the prototype is 93% and 89% for step‐up and step‐down modes, respectively. To evaluate the effect of proposed SPO for extracting maximum available power from PVs, simulation results of a grid connected PV system with two series connected SPOs is discussed.
- Open Access
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 14 (3) , 2466-2479
Voltage and frequency control of microgrid in presence of micro-turbine interfaced to matrix converter
The active and reactive load changes have a significant impact on voltage and frequency. In this paper, in order to stabilize the microgrid (MG) against load variations in islanding mode, the active and reactive power of all distributed generators (DGs), including energy storage (battery), diesel generator, and micro-turbine, are controlled. The micro-turbine generator is connected to MG through a three-phase to three-phase matrix converter, and the droop control method is applied for controlling the voltage and frequency of MG. In addition, a method is introduced for voltage and frequency control of micro-turbines in the transition state from grid-connected mode to islanding mode. A novel switching strategy of the matrix converter is used for converting the high-frequency output voltage of the micro-turbine to the grid-side frequency of the utility system. Moreover, using the switching strategy, the low-order harmonics in the output current and voltage are not produced, and consequently, the size of the output filter would be reduced. In fact, the suggested control strategy is load-independent and has no frequency conversion restrictions. The proposed approach for voltage and frequency regulation demonstrates exceptional performance and favorable response across various load alteration scenarios. The suggested strategy is examined in several scenarios in the MG test systems, and the simulation results are addressed.
- 1 June 2024
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 14 (3) , 2466-2479
Open AccessVoltage and frequency control of microgrid in presence of micro-turbine interfaced to matrix converter
The active and reactive load changes have a significant impact on voltage and frequency. In this paper, in order to stabilize the microgrid (MG) against load variations in islanding mode, the active and reactive power of all distributed generators (DGs), including energy storage (battery), diesel generator, and micro-turbine, are controlled. The micro-turbine generator is connected to MG through a three-phase to three-phase matrix converter, and the droop control method is applied for controlling the voltage and frequency of MG. In addition, a method is introduced for voltage and frequency control of micro-turbines in the transition state from grid-connected mode to islanding mode. A novel switching strategy of the matrix converter is used for converting the high-frequency output voltage of the micro-turbine to the grid-side frequency of the utility system. Moreover, using the switching strategy, the low-order harmonics in the output current and voltage are not produced, and consequently, the size of the output filter would be reduced. In fact, the suggested control strategy is load-independent and has no frequency conversion restrictions. The proposed approach for voltage and frequency regulation demonstrates exceptional performance and favorable response across various load alteration scenarios. The suggested strategy is examined in several scenarios in the MG test systems, and the simulation results are addressed.
- Open Access
- 14 February 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (4) , 564-575
A soft switched step‐up DC–DC converter using a low‐power auxiliary circuit and continuous input current
In this paper, a new high step‐up DC–DC converter is presented. The presence of an inductor at converter input reduces input current ripple. Furthermore, a coupled inductor with a voltage multiplier cell is also implemented to increase the voltage gain of the converter. The stored energy in leakage inductance of coupled inductor is recycled by a clamp circuit which increases efficiency and clamps voltage on power switch. The power switch is turned on and off under soft switching condition. The soft switching is also applied to auxiliary switch. All diodes are turned off under zero current condition which causes reverse recovery problem to be alleviated. A very low current flows through auxiliary components in a very short time. Therefore, a very low conduction loss is added to the converter by an auxiliary circuit. Soft switching condition is almost independent of specifications of circuit, especially the output power. Steady‐state analysis of the proposed converter is discussed. Finally, to verify the performance and validation of the proposed converter, laboratory results for a prototype with input voltage 30 V, output voltage 240 V, output power 220 W and switching frequency 50 kHz are presented and the results are discussed. The efficiency of the prototype converter at nominal power is 96%.
- 14 February 2024
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 17 (4) , 564-575
Open AccessA soft switched step‐up DC–DC converter using a low‐power auxiliary circuit and continuous input current
In this paper, a new high step‐up DC–DC converter is presented. The presence of an inductor at converter input reduces input current ripple. Furthermore, a coupled inductor with a voltage multiplier cell is also implemented to increase the voltage gain of the converter. The stored energy in leakage inductance of coupled inductor is recycled by a clamp circuit which increases efficiency and clamps voltage on power switch. The power switch is turned on and off under soft switching condition. The soft switching is also applied to auxiliary switch. All diodes are turned off under zero current condition which causes reverse recovery problem to be alleviated. A very low current flows through auxiliary components in a very short time. Therefore, a very low conduction loss is added to the converter by an auxiliary circuit. Soft switching condition is almost independent of specifications of circuit, especially the output power. Steady‐state analysis of the proposed converter is discussed. Finally, to verify the performance and validation of the proposed converter, laboratory results for a prototype with input voltage 30 V, output voltage 240 V, output power 220 W and switching frequency 50 kHz are presented and the results are discussed. The efficiency of the prototype converter at nominal power is 96%.
- Open Access
- 1 December 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 13 (6) , 6141-6155
Design and implementation a novel single switch high gain DC-DC converter based on coupled inductor with low-ripple input current
A novel high-gain and high-efficiency direct current to direct current (DC-DC) converter is introduced in this paper. The presented converter is suitable for low-voltage renewable energy resources such as photovoltaic (PV) and fuel cell (FC). The existence of series inductance with the input source ensures continuous and low-ramp input current, which is important for extracting maximum power from resources. Using coupled inductor technology and an intermediate capacitor in the suggested converter leads to a high gain voltage. In the presented topology for recovering energy from the leakage inductor, reducing voltage stress on the power switch, and so decreasing overall converter losses, a passive clamp circuit is used. The suitable operation range of duty cycle in the converter, besides the leakage inductor, decreases the problem of reverse recovery in diodes. The low value of the leakage inductor and the low volume and cost of the proposed converter are due to the low turn ratio of the coupled inductor. Details of the operation principles of the proposed converter have been discussed in this paper. The presented simulation and laboratory prototype results verify the theoretical analysis and performance of the suggested topology.
- 1 December 2023
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 13 (6) , 6141-6155
Open AccessDesign and implementation a novel single switch high gain DC-DC converter based on coupled inductor with low-ripple input current
A novel high-gain and high-efficiency direct current to direct current (DC-DC) converter is introduced in this paper. The presented converter is suitable for low-voltage renewable energy resources such as photovoltaic (PV) and fuel cell (FC). The existence of series inductance with the input source ensures continuous and low-ramp input current, which is important for extracting maximum power from resources. Using coupled inductor technology and an intermediate capacitor in the suggested converter leads to a high gain voltage. In the presented topology for recovering energy from the leakage inductor, reducing voltage stress on the power switch, and so decreasing overall converter losses, a passive clamp circuit is used. The suitable operation range of duty cycle in the converter, besides the leakage inductor, decreases the problem of reverse recovery in diodes. The low value of the leakage inductor and the low volume and cost of the proposed converter are due to the low turn ratio of the coupled inductor. Details of the operation principles of the proposed converter have been discussed in this paper. The presented simulation and laboratory prototype results verify the theoretical analysis and performance of the suggested topology.
- Open Access
- 11 June 2023
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 16 (12) , 2065-2075
Comprehensive reliability evaluation of three types of connection of DC–DC converters: single‐phase, two‐phase, and parallel input‐series output
With the increasing use of power electronic converters, the reliability studies of these converters are essential. The most important factor in increasing the reliability of power converters is their structures. In this paper the reliability evaluation of a DC–DC converter with various connections including single‐phase, interleaved, and parallel‐input and series‐output (PISO) topologies is presented. In the first view, it seems that the interleave topology has high reliability, but considering the more presented detailed indexes, it is identified that the PISO structure has a higher reliability than the interleave structure. In this paper for better evaluation, the various topologies are considered which operate at full rated power and half power. To calculate the reliability of the converters the important parameters such as the thermal and electrical stresses of elements are considered. The Markov model is used to evaluate the reliability. In order to verify the presented studies and analysis, the DC–DC converters with single‐phase, interleaved, and PISO have been implemented. The experimental results show that the PISO topology has higher reliability.
- 11 June 2023
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 16 (12) , 2065-2075
Open AccessComprehensive reliability evaluation of three types of connection of DC–DC converters: single‐phase, two‐phase, and parallel input‐series output
With the increasing use of power electronic converters, the reliability studies of these converters are essential. The most important factor in increasing the reliability of power converters is their structures. In this paper the reliability evaluation of a DC–DC converter with various connections including single‐phase, interleaved, and parallel‐input and series‐output (PISO) topologies is presented. In the first view, it seems that the interleave topology has high reliability, but considering the more presented detailed indexes, it is identified that the PISO structure has a higher reliability than the interleave structure. In this paper for better evaluation, the various topologies are considered which operate at full rated power and half power. To calculate the reliability of the converters the important parameters such as the thermal and electrical stresses of elements are considered. The Markov model is used to evaluate the reliability. In order to verify the presented studies and analysis, the DC–DC converters with single‐phase, interleaved, and PISO have been implemented. The experimental results show that the PISO topology has higher reliability.
- 1 October 2019
- Published by Springer Nature in Journal of Central South University
- Vol. 26 (10) , 2833-2844
A general analytical approach to reach maximum grid support by PMSG-based wind turbines under various grid faults
- 1 October 2019
- Published by Springer Nature in Journal of Central South University
- Vol. 26 (10) , 2833-2844
A general analytical approach to reach maximum grid support by PMSG-based wind turbines under various grid faults
- 26 December 2018
- Published by Wiley in International Transactions on Electrical Energy Systems
- Vol. 29 (4) , e2801
Analysis and implementation of a novel three input DC‐DC boost converter for sustainable energy applications
- 26 December 2018
- Published by Wiley in International Transactions on Electrical Energy Systems
- Vol. 29 (4) , e2801
Analysis and implementation of a novel three input DC‐DC boost converter for sustainable energy applications
- Open Access
- 1 November 2018
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 11 (13) , 2053-2062
Coupled‐winding‐based 11‐level inverter: design and cost analysis
A new 11‐level inverter using a coupled inductor and a transformer is proposed. The proposed inverter increases maximum output voltage and decreases current stress on switches. A comprehensive comparison is conducted among the proposed inverter and some of the recent presented inverters in terms of number of components, maximum output voltage, and voltage and current stresses on the switches. Moreover, the design calculations of a single‐phase inverter in addition to the transformer and coupled inductor design are given. In order to verify the performance of the proposed topologies, the experimental results are presented.
- 1 November 2018
- Published by Institution of Engineering and Technology (IET) in IET Power Electronics
- Vol. 11 (13) , 2053-2062
Open AccessCoupled‐winding‐based 11‐level inverter: design and cost analysis
A new 11‐level inverter using a coupled inductor and a transformer is proposed. The proposed inverter increases maximum output voltage and decreases current stress on switches. A comprehensive comparison is conducted among the proposed inverter and some of the recent presented inverters in terms of number of components, maximum output voltage, and voltage and current stresses on the switches. Moreover, the design calculations of a single‐phase inverter in addition to the transformer and coupled inductor design are given. In order to verify the performance of the proposed topologies, the experimental results are presented.