Mustafa Esen Marti
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Mustafa Esen Marti has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Hani Zeidan
Department of Applied Chemistry, Faculty of Science, Idlib University, Idlib, Syria
8 shared publications Hani Zeidan
Department of Chemical Engineering Konya Technical University Konya Turkey
4 shared publications- Ebru Erünal
Department of Chemical Engineering, Gebze Technical University, Kocaeli, Turkey
2 shared publications H. Zeidan
Department of Chemical Engineering, Konya Technical University, Konya, Türkiye
2 shared publicationsMukaddes Can
Department of Chemical Engineering, Konya Technical University, Konya, Turkey
2 shared publications- Anup Dutt Sharma
Department of Chemical and Biological Engineering, Iowa State University, Ames, IA 50011, United States; Neuroscience Program, Iowa State University, Ames, IA 50011, United States
1 shared publication
Latest Publications
- 28 August 2026
- Published by Pleiades Publishing Ltd in Colloid Journal
- Vol. 88 (5) , 915-930
Adsorption of Phenolic Compounds onto Reusable CeO2@SiO2 Nanocomposites: Kinetics, Equilibrium, and Thermodynamics in Batch and Column Systems
The recovery of phenol from aqueous solutions using CeO2−SiO2 nanocomposites was investigated. The optimal pH value for the process was determined to be 3. Higher phenol concentration decreased separation efficiency while increasing adsorption capacity. Conversely, increasing the adsorbent dosage led to a higher separation efficiency but lower adsorption capacity. The highest batch adsorption capacity (136 mg/g) and maximum efficiency were achieved with CeSi-3 (CeO2 : SiO2 = 1 : 0.5), which possesses the highest cerium oxide content. Higher temperatures reduced both adsorption efficiency and capacity. Thermodynamic parameters indicate that the process is non-spontaneous and exothermic. The isotherm, thermodynamic, and kinetic analyses demonstrated that the adsorption process was governed by a combination of physical and chemical interactions. Complete desorption (100%) was achieved using 0.5 M NaOH, and following ten reuse cycles of CeSi-3, the removal efficiency decreased from 72 to 50%. Column studies revealed that adsorption capacity was influenced by flow rate and bed height. The maximum adsorption capacity (qe = 63.3 mg/g) was achieved at a flow rate of 3 mL/min and a bed height of 80 mm. In this research, CeO2−SiO2 nanocomposites exhibit significant potential for sustainable recovery of phenolic compounds, according to their superior performance, reusability, and efficient desorption capabilities.
- 28 August 2026
- Published by Pleiades Publishing Ltd in Colloid Journal
- Vol. 88 (5) , 915-930
Adsorption of Phenolic Compounds onto Reusable CeO2@SiO2 Nanocomposites: Kinetics, Equilibrium, and Thermodynamics in Batch and Column Systems
The recovery of phenol from aqueous solutions using CeO2−SiO2 nanocomposites was investigated. The optimal pH value for the process was determined to be 3. Higher phenol concentration decreased separation efficiency while increasing adsorption capacity. Conversely, increasing the adsorbent dosage led to a higher separation efficiency but lower adsorption capacity. The highest batch adsorption capacity (136 mg/g) and maximum efficiency were achieved with CeSi-3 (CeO2 : SiO2 = 1 : 0.5), which possesses the highest cerium oxide content. Higher temperatures reduced both adsorption efficiency and capacity. Thermodynamic parameters indicate that the process is non-spontaneous and exothermic. The isotherm, thermodynamic, and kinetic analyses demonstrated that the adsorption process was governed by a combination of physical and chemical interactions. Complete desorption (100%) was achieved using 0.5 M NaOH, and following ten reuse cycles of CeSi-3, the removal efficiency decreased from 72 to 50%. Column studies revealed that adsorption capacity was influenced by flow rate and bed height. The maximum adsorption capacity (qe = 63.3 mg/g) was achieved at a flow rate of 3 mL/min and a bed height of 80 mm. In this research, CeO2−SiO2 nanocomposites exhibit significant potential for sustainable recovery of phenolic compounds, according to their superior performance, reusability, and efficient desorption capabilities.
- 1 June 2026
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 98 (10) , 630-640
Reactive Extraction of Tartaric Acid Using Sustainable and Eco‐Friendly Solvents From Aqueous Media
This study investigates the use of vegetable oils as sustainable diluents in the reactive extraction of tartaric acid (TA) using trioctylamine (TOA). Their performance was compared with 1‐octanol as a reference solvent. All oils showed comparable efficiencies, with canola oil (CNO) performing slightly better. Extraction was strongly affected by pH, temperature, and concentrations. The highest efficiency was obtained at the natural pH (1.42), whereas higher temperatures and TA concentrations reduced performance. Increasing TOA concentration improved extraction. Under optimal conditions (0.2 M TA, 1.0 M TOA, and 298.15 K), efficiencies reached 91% (distribution coefficient, K D = 10.11) for CNO and 97.2% ( K D = 35.1) for 1‐octanol. More than 99% of TA was recovered from the loaded organic phase, and the organic phase was reused with minimal loss. These results demonstrate that vegetable oils are promising green alternatives for TA extraction.
- 1 June 2026
- Published by Wiley in Chemie Ingenieur Technik
- Vol. 98 (10) , 630-640
Reactive Extraction of Tartaric Acid Using Sustainable and Eco‐Friendly Solvents From Aqueous Media
This study investigates the use of vegetable oils as sustainable diluents in the reactive extraction of tartaric acid (TA) using trioctylamine (TOA). Their performance was compared with 1‐octanol as a reference solvent. All oils showed comparable efficiencies, with canola oil (CNO) performing slightly better. Extraction was strongly affected by pH, temperature, and concentrations. The highest efficiency was obtained at the natural pH (1.42), whereas higher temperatures and TA concentrations reduced performance. Increasing TOA concentration improved extraction. Under optimal conditions (0.2 M TA, 1.0 M TOA, and 298.15 K), efficiencies reached 91% (distribution coefficient, K D = 10.11) for CNO and 97.2% ( K D = 35.1) for 1‐octanol. More than 99% of TA was recovered from the loaded organic phase, and the organic phase was reused with minimal loss. These results demonstrate that vegetable oils are promising green alternatives for TA extraction.
- 13 May 2026
- Published by Wiley in Chemical Engineering & Technology
- Vol. 49 (5) , e70233
Highly Selective and Effective Adsorption of Ionic Dyes Using Reusable CeO 2 –SiO 2 Nanoadsorbents
CeO 2 –SiO 2 nanoadsorbents synthesized via a simple and energy‐efficient approach were used for the removal of ionic dyes from single and binary aqueous solutions. The effects of pH, temperature, contact time, and adsorbate/adsorbent dosage on adsorption performance were examined as a function of the CeO 2 –SiO 2 ratio. Adsorption isotherms, kinetics, and thermodynamic parameters were interpreted using characterization data and theoretical models. The adsorbent with the highest CeO 2 content exhibited the best adsorption performance, following pseudo‐second‐order kinetics and showing strong pH dependence. High selectivity (>97%) was obtained. Moreover, effective desorption and good reusability were observed, with only a slight decline in adsorption efficiency after 10 cycles. Continuous adsorption experiments conducted in a packed column revealed good agreement with the Thomas model, yielding breakthrough capacities of 86.22 and 78.18 mg g −1 for RR120 and MB, respectively.
- 13 May 2026
- Published by Wiley in Chemical Engineering & Technology
- Vol. 49 (5) , e70233
Highly Selective and Effective Adsorption of Ionic Dyes Using Reusable CeO 2 –SiO 2 Nanoadsorbents
CeO 2 –SiO 2 nanoadsorbents synthesized via a simple and energy‐efficient approach were used for the removal of ionic dyes from single and binary aqueous solutions. The effects of pH, temperature, contact time, and adsorbate/adsorbent dosage on adsorption performance were examined as a function of the CeO 2 –SiO 2 ratio. Adsorption isotherms, kinetics, and thermodynamic parameters were interpreted using characterization data and theoretical models. The adsorbent with the highest CeO 2 content exhibited the best adsorption performance, following pseudo‐second‐order kinetics and showing strong pH dependence. High selectivity (>97%) was obtained. Moreover, effective desorption and good reusability were observed, with only a slight decline in adsorption efficiency after 10 cycles. Continuous adsorption experiments conducted in a packed column revealed good agreement with the Thomas model, yielding breakthrough capacities of 86.22 and 78.18 mg g −1 for RR120 and MB, respectively.
- Open Access
- 30 March 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (14) , 7699-7710
Selective Cu(II) Adsorption Using a Smart Amine-Functionalized and Activated Carbon-Supported CeO 2 @SiO 2 Composite
- 30 March 2026
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 65 (14) , 7699-7710
Open AccessSelective Cu(II) Adsorption Using a Smart Amine-Functionalized and Activated Carbon-Supported CeO 2 @SiO 2 Composite
- Open Access
- 23 May 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (21) , 21450-21462
A Novel Architecture Based on a Pyrrole-Functionalized Dithieno[3,2-b:2′,3′-d]pyrrole (DTP)-Type Conducting Polymer and Thiol-Modified Calixarene Derivative for Biophotovoltaic Solar Cells: Photocurrent and Hydrogen Generations via Both Photosynthesis and Respiratory System
This review explores the potential of biophotovoltaic devices (BPVs) as a sustainable solution for addressing the global energy crisis and combating climate change. BPVs generate renewable electricity from sunlight and water through the photosynthetic activity of microorganisms such as cyanobacteria and algae, which act as living photocatalysts. The study essentially focuses on improving photocurrent outputs through developing efficient anode materials. An innovative photoanode design is introduced employing cyanobacteria immobilized on a P(DTP-Ph-Pyr)/Calixarene-AuNP-modified surface. This design features a porous structure conducive to cyanobacterial attachment and efficient electron transfer. As a first step, the conductive polymeric film of 4-(4-(1H-pyrrol-1-yl)phenyl)-4H-dithieno[3,2-b:2′,3′-d]pyrrole (DTP-Ph-Pyr) monomer was coated onto a gold electrode via electropolymerization method. Then, a mixture of thiol- and carboxylic group-modified calixarene and gold nanoparticles (AuNPs) was applied to enhance the photoelectrode’s performance. The surface of the modified electrode enabled the successful immobilization of Leptolyngbya sp. cyanobacterial cells, providing a reliable interface for efficient photocurrent and hydrogen generation. Calixarenes and their derivatives act as favorable agents for cyanobacterial immobilization due to their specific configurations. Moreover, the formation of covalent bonds between the carboxyl groups of calixarenes and the amino groups in cyanobacteria facilitates the robust immobilization of cyanobacterial cells while maintaining their well-ordered structural integrity and organized cellular architecture. A complementary cathode structure, employing aniline-modified Pt nanoparticles, facilitates the reduction of protons to generate hydrogen gas. Overall, this study underscores the promise of BPVs as feasible clean energy technologies and introduces innovative methods to improve their efficiency and sustainability.
- 23 May 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (21) , 21450-21462
Open AccessA Novel Architecture Based on a Pyrrole-Functionalized Dithieno[3,2-b:2′,3′-d]pyrrole (DTP)-Type Conducting Polymer and Thiol-Modified Calixarene Derivative for Biophotovoltaic Solar Cells: Photocurrent and Hydrogen Generations via Both Photosynthesis and Respiratory System
This review explores the potential of biophotovoltaic devices (BPVs) as a sustainable solution for addressing the global energy crisis and combating climate change. BPVs generate renewable electricity from sunlight and water through the photosynthetic activity of microorganisms such as cyanobacteria and algae, which act as living photocatalysts. The study essentially focuses on improving photocurrent outputs through developing efficient anode materials. An innovative photoanode design is introduced employing cyanobacteria immobilized on a P(DTP-Ph-Pyr)/Calixarene-AuNP-modified surface. This design features a porous structure conducive to cyanobacterial attachment and efficient electron transfer. As a first step, the conductive polymeric film of 4-(4-(1H-pyrrol-1-yl)phenyl)-4H-dithieno[3,2-b:2′,3′-d]pyrrole (DTP-Ph-Pyr) monomer was coated onto a gold electrode via electropolymerization method. Then, a mixture of thiol- and carboxylic group-modified calixarene and gold nanoparticles (AuNPs) was applied to enhance the photoelectrode’s performance. The surface of the modified electrode enabled the successful immobilization of Leptolyngbya sp. cyanobacterial cells, providing a reliable interface for efficient photocurrent and hydrogen generation. Calixarenes and their derivatives act as favorable agents for cyanobacterial immobilization due to their specific configurations. Moreover, the formation of covalent bonds between the carboxyl groups of calixarenes and the amino groups in cyanobacteria facilitates the robust immobilization of cyanobacterial cells while maintaining their well-ordered structural integrity and organized cellular architecture. A complementary cathode structure, employing aniline-modified Pt nanoparticles, facilitates the reduction of protons to generate hydrogen gas. Overall, this study underscores the promise of BPVs as feasible clean energy technologies and introduces innovative methods to improve their efficiency and sustainability.
- 12 December 2024
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 103 (7) , 3368-3378
Adsorptive separation of propionic acid from aqueous medium using efficient anion exchange resins in batch and fixed bed column systems
The recovery of propionic acid (PA) from aqueous medium using a strongly basic, Lewatit M‐600 (LM‐600), and a weakly basic, Lewatit MP‐62 (LMP‐62), anion exchanger was investigated. Medium conditions such as pH, temperature, PA concentration, and resin dose affected the performance of the process. The highest capacities were achieved at pH 5 and 2 with LM‐600 and LMP‐62, respectively. Equilibrium was reached in 35 min, and the process followed the pseudo‐second‐order kinetics for both anion exchangers. LMP‐62 was more effective at pH values lower than 5. The exothermic process was found to be spontaneous. The maximum capacities of the strong and weak basic exchangers in batch experiments were 135.7 and 363 mg/g, respectively. However, the breakthrough capacities obtained in fixed bed systems were lower than those attained in batch systems (94.75 and 123.73 mg/g for LM‐600 and LMP‐62, respectively), and the column was successfully regenerated using 0.6 M NaOH. The Freundlich isotherm model yielded the highest determination coefficients in the isotherm analysis, suggesting that physical forces between PA and resins primarily drive the process.
- 12 December 2024
- Published by Wiley in The Canadian Journal of Chemical Engineering
- Vol. 103 (7) , 3368-3378
Adsorptive separation of propionic acid from aqueous medium using efficient anion exchange resins in batch and fixed bed column systems
The recovery of propionic acid (PA) from aqueous medium using a strongly basic, Lewatit M‐600 (LM‐600), and a weakly basic, Lewatit MP‐62 (LMP‐62), anion exchanger was investigated. Medium conditions such as pH, temperature, PA concentration, and resin dose affected the performance of the process. The highest capacities were achieved at pH 5 and 2 with LM‐600 and LMP‐62, respectively. Equilibrium was reached in 35 min, and the process followed the pseudo‐second‐order kinetics for both anion exchangers. LMP‐62 was more effective at pH values lower than 5. The exothermic process was found to be spontaneous. The maximum capacities of the strong and weak basic exchangers in batch experiments were 135.7 and 363 mg/g, respectively. However, the breakthrough capacities obtained in fixed bed systems were lower than those attained in batch systems (94.75 and 123.73 mg/g for LM‐600 and LMP‐62, respectively), and the column was successfully regenerated using 0.6 M NaOH. The Freundlich isotherm model yielded the highest determination coefficients in the isotherm analysis, suggesting that physical forces between PA and resins primarily drive the process.
- Open Access
- 4 December 2024
- Published by Society of Chemists and Technologists of Macedonia in Macedonian Journal of Chemistry and Chemical Engineering
- Vol. 43 (2) , 257-270
Preparation, characterization, and use of trimethoxy[3-(methylamino)propyl]silane functionalized SBA-15 for Congo Red adsorption
Mesoporous materials have a broad range of applications in industry, and one of which is their potential use in adsorptive separations. This research investigates the use of a secondary amine-functionalized SBA-15 for the separation of a diazo dye, Congo Red (CR), from aqueous solutions. The synthesized SBA-15 was modified with trimethoxy[3-(methylamino)propyl] silane by a post-grafting method. The produced material was characterized using X-ray diffraction, N2 physisorption, scanning electron microscopy, and transmission electron microscopy. The hexagonal mesostructure was preserved after functionalization; however, the specific surface area, pore diameter, and total pore volume of SBA-15 silica decreased. The adsorption of the diazo dye reached equilibrium by 50 minutes, and the data followed pseudo-second-order kinetics. While the yield increased with rising dosage and temperature, it decreased with CR concentration. The maximum adsorption capacity of functionalized SBA-15 (F-SBA-15) for CR uptake was found to be 211.07 mg/g. Thermodynamic data and parameters indicated the potential combination of physical and chemical interactions occurring during the adsorption process. The separation was endothermic and non-spontaneous; the equilibrium data fitted to the Freundlich adsorption isotherm at all tested temperatures. This study demonstrates that the secondary amine-functionalized SBA-15 can be used for the elimination of a toxic anionic diazo dye from aqueous solutions.
- 4 December 2024
- Published by Society of Chemists and Technologists of Macedonia in Macedonian Journal of Chemistry and Chemical Engineering
- Vol. 43 (2) , 257-270
Open AccessPreparation, characterization, and use of trimethoxy[3-(methylamino)propyl]silane functionalized SBA-15 for Congo Red adsorption
Mesoporous materials have a broad range of applications in industry, and one of which is their potential use in adsorptive separations. This research investigates the use of a secondary amine-functionalized SBA-15 for the separation of a diazo dye, Congo Red (CR), from aqueous solutions. The synthesized SBA-15 was modified with trimethoxy[3-(methylamino)propyl] silane by a post-grafting method. The produced material was characterized using X-ray diffraction, N2 physisorption, scanning electron microscopy, and transmission electron microscopy. The hexagonal mesostructure was preserved after functionalization; however, the specific surface area, pore diameter, and total pore volume of SBA-15 silica decreased. The adsorption of the diazo dye reached equilibrium by 50 minutes, and the data followed pseudo-second-order kinetics. While the yield increased with rising dosage and temperature, it decreased with CR concentration. The maximum adsorption capacity of functionalized SBA-15 (F-SBA-15) for CR uptake was found to be 211.07 mg/g. Thermodynamic data and parameters indicated the potential combination of physical and chemical interactions occurring during the adsorption process. The separation was endothermic and non-spontaneous; the equilibrium data fitted to the Freundlich adsorption isotherm at all tested temperatures. This study demonstrates that the secondary amine-functionalized SBA-15 can be used for the elimination of a toxic anionic diazo dye from aqueous solutions.
- 17 October 2024
- Published by Croatian Society of Chemical Engineers/HDKI in Chemical and Biochemical Engineering Quarterly
- Vol. 38 (3) , 207-217
Efficient Separation of Levulinic Acid Using Fly Ash from Sugar Beet Processing
Levulinic acid (LA) is a significant building block in industry. It can be produced by the hydrolysis of lignocellulosic feedstocks and needs to be separated from the aqueous production medium. This study focuses on evaluating fly ash, a waste byproduct from a sugar factory, for use in the adsorption of LA from aqueous media. The sugar beet processing fly ash (SBFA) was characterized using XRD, FTIR, SEM, and N2 adsorption-desorption analysis. The data fit the pseudo-second-order kinetic model, with good agreement between the experimentally measured (454.55 mg g–1) and calculated (452.40 mg g–1) adsorption capacities. It was observed that the efficiency slightly decreased with increasing temperature, with the effect more pronounced at lower concentrations. Calculated thermodynamic parameters demonstrated that the process was exergonic and exothermic. The capacity of LA adsorption reduced with SBFA dose while enhanced with acid concentration, achieving a maximum of 464 mg LA/g SBFA, higher than values previously achieved with other adsorbents. The Langmuir isotherm model fit well with equilibrium data. Complete recovery of LA was achieved using 0.2 M NaOH, and SBFA could be reused with high efficiency for five consecutive cycles.
- 17 October 2024
- Published by Croatian Society of Chemical Engineers/HDKI in Chemical and Biochemical Engineering Quarterly
- Vol. 38 (3) , 207-217
Efficient Separation of Levulinic Acid Using Fly Ash from Sugar Beet Processing
Levulinic acid (LA) is a significant building block in industry. It can be produced by the hydrolysis of lignocellulosic feedstocks and needs to be separated from the aqueous production medium. This study focuses on evaluating fly ash, a waste byproduct from a sugar factory, for use in the adsorption of LA from aqueous media. The sugar beet processing fly ash (SBFA) was characterized using XRD, FTIR, SEM, and N2 adsorption-desorption analysis. The data fit the pseudo-second-order kinetic model, with good agreement between the experimentally measured (454.55 mg g–1) and calculated (452.40 mg g–1) adsorption capacities. It was observed that the efficiency slightly decreased with increasing temperature, with the effect more pronounced at lower concentrations. Calculated thermodynamic parameters demonstrated that the process was exergonic and exothermic. The capacity of LA adsorption reduced with SBFA dose while enhanced with acid concentration, achieving a maximum of 464 mg LA/g SBFA, higher than values previously achieved with other adsorbents. The Langmuir isotherm model fit well with equilibrium data. Complete recovery of LA was achieved using 0.2 M NaOH, and SBFA could be reused with high efficiency for five consecutive cycles.
- Open Access
- 22 May 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (24) , 16765-16777
Effective isolation of succinic acid from aqueous media with the use of anion exchange resins
The primary objective of this study was to examine the isolation of succinic acid (SA) from aqueous-based solutions through the utilization of adsorption and ion exchange methods. Four kinds of anion exchange resins were employed, two of which were strong basic (Lewatit M-500 and Lewatit M-600), and the other two were weak basic (Lewatit MP-64 and Lewatit MP-62). The impacts of various variables on the efficiency of the process were examined. The aqueous pH strongly influenced the separation yield. Weak basic exchangers achieved the maximum yield at pH 2.1. However, the highest performance with Lewatit M-600 and Lewatit M-500 was obtained at pH 5 and 6, respectively. The SA separation with the tested resins reached equilibrium in about an hour. The recovery data revealed consistency with the Langmuir isotherm and pseudo-second-order kinetics. Efficiency improved with resin dosage and reduced with SA concentration. It was found that weak basic anion exchange resins were more efficient than strong basic exchangers for the recovery process. Among the resins tested, Lewatit MP-62 demonstrated the highest sorption capacity of 321 mg g−1 and 97.5% yield. The performance of the system decreased with temperature for all alternatives tested; however, its impact was not notable. The isolation process had an exergonic, exothermic, and favorable character based on the thermodynamic constants. Acid-loaded resins were successfully regenerated using trimethylamine and HCl for weak and strong anion exchange resins, respectively.
- 22 May 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (24) , 16765-16777
Open AccessEffective isolation of succinic acid from aqueous media with the use of anion exchange resins
The primary objective of this study was to examine the isolation of succinic acid (SA) from aqueous-based solutions through the utilization of adsorption and ion exchange methods. Four kinds of anion exchange resins were employed, two of which were strong basic (Lewatit M-500 and Lewatit M-600), and the other two were weak basic (Lewatit MP-64 and Lewatit MP-62). The impacts of various variables on the efficiency of the process were examined. The aqueous pH strongly influenced the separation yield. Weak basic exchangers achieved the maximum yield at pH 2.1. However, the highest performance with Lewatit M-600 and Lewatit M-500 was obtained at pH 5 and 6, respectively. The SA separation with the tested resins reached equilibrium in about an hour. The recovery data revealed consistency with the Langmuir isotherm and pseudo-second-order kinetics. Efficiency improved with resin dosage and reduced with SA concentration. It was found that weak basic anion exchange resins were more efficient than strong basic exchangers for the recovery process. Among the resins tested, Lewatit MP-62 demonstrated the highest sorption capacity of 321 mg g−1 and 97.5% yield. The performance of the system decreased with temperature for all alternatives tested; however, its impact was not notable. The isolation process had an exergonic, exothermic, and favorable character based on the thermodynamic constants. Acid-loaded resins were successfully regenerated using trimethylamine and HCl for weak and strong anion exchange resins, respectively.
- Open Access
- 3 April 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (15) , 16959-16968
Eco-Friendly Approach for the Recovery of Lactic Acid by Complex Extraction
To meet the growing demand for high-purity lactic acid (LA) for biocompatible and biodegradable polymers, LA recovery by green techniques has been attracting the attention. This study focuses on the evaluation of vegetable oils as organic phase diluents in complex extraction of LA with an aliphatic tertiary amine extractant, trioctylamine (TOA). Eight vegetable oils were tested, and their performances were evaluated individually and compared with those obtained using 1-octanol. Extraction yields with these oils were similar; however, efficiencies with safflower oil (SFO) were slightly higher than those obtained with other oils tested. Efficiency with SFO + TOA varied inversely with temperature and pH; however, it increased with higher LA and TOA concentrations. Within the ranges of parameters investigated, the highest yield in SFO was 66% and was achieved at the highest TOA (1.0 M) and LA (1.5 M) concentrations. The efficiency obtained in 1-octanol under the identical conditions was 76%. Thus, the yields obtained with SFO + TOA and 1-octanol + TOA were comparable under most of the conditions tested, especially at the higher LA concentrations, which is preferred for commercial production. Following that, >99% of the LA was transferred from the organic phase to the (second) aqueous phase using NaOH (1.0 M) as a stripping agent. The organic phase was tested in subsequent extractions, and yields comparable to those obtained in the first uses were achieved. This study demonstrated that vegetable oils have the potential to be used as organic phase diluents during complex extraction of LA.
- 3 April 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (15) , 16959-16968
Open AccessEco-Friendly Approach for the Recovery of Lactic Acid by Complex Extraction
To meet the growing demand for high-purity lactic acid (LA) for biocompatible and biodegradable polymers, LA recovery by green techniques has been attracting the attention. This study focuses on the evaluation of vegetable oils as organic phase diluents in complex extraction of LA with an aliphatic tertiary amine extractant, trioctylamine (TOA). Eight vegetable oils were tested, and their performances were evaluated individually and compared with those obtained using 1-octanol. Extraction yields with these oils were similar; however, efficiencies with safflower oil (SFO) were slightly higher than those obtained with other oils tested. Efficiency with SFO + TOA varied inversely with temperature and pH; however, it increased with higher LA and TOA concentrations. Within the ranges of parameters investigated, the highest yield in SFO was 66% and was achieved at the highest TOA (1.0 M) and LA (1.5 M) concentrations. The efficiency obtained in 1-octanol under the identical conditions was 76%. Thus, the yields obtained with SFO + TOA and 1-octanol + TOA were comparable under most of the conditions tested, especially at the higher LA concentrations, which is preferred for commercial production. Following that, >99% of the LA was transferred from the organic phase to the (second) aqueous phase using NaOH (1.0 M) as a stripping agent. The organic phase was tested in subsequent extractions, and yields comparable to those obtained in the first uses were achieved. This study demonstrated that vegetable oils have the potential to be used as organic phase diluents during complex extraction of LA.