Jun Cai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jun Cai has a total of 76 co-authors. Here are the top co-authors by number of shared publications:
- Guoping Qian
School of Transportation, Changsha University of Science & Technology
4 shared publications Haochuang Zhao
4 shared publicationsHai Ning
3 shared publicationsHuanan Yu
3 shared publicationsWangzhou Li
3 shared publicationsFan Gu
2 shared publications
Latest Publications
- Open Access
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
An Integrated Pavement-Roadside Cascade Purification System for Porous Cement Concrete: Construction and Performance Based on Synergistic Physical Adsorption and Biodegradation
Increased highway traffic has caused a sharp rise in pollutants from service areas, threatening the surrounding water environment. Conventional paving materials cannot balance purification with structural performance, while typical Low Impact Development (LID) techniques require large land areas, hindering efficient pollutant degradation in parking and refueling zones. To address this, an integrated “Graded Porous Cement Concrete (PC) Pavement–Roadside Cascade Purification System (CPS)” is proposed, using a synergistic “physical filtration/adsorption – biodegradation/absorption” pathway. Experimental results show: (1) Short-term operation achieved near-complete removal (≈100%) of Total Phosphorus (TP), Suspended Solids (SS), and heavy metals, with initial Total Nitrogen (TN) and Chemical Oxygen Demand (COD) removal rates of 76.8% and 61.9%, respectively. (2) The system demonstrated sustained capacity. After seven cycles (simulating three months of runoff), TN and TP removal rates remained at 58.8% and 41.1%. Using a COD removal rate of 10% as a failure threshold, performance was effectively restored by rinsing and replacing activated carbon. (3) Micro-characterization (SEM-EDS, FTIR, XRD) revealed that removal occurs through synergistic physical filtration/adsorption, chemical ion exchange, and biodegradation/absorption. This study provides a technically, economically, and operationally feasible integrated solution for highway service area runoff pollution control.
- 4 June 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAn Integrated Pavement-Roadside Cascade Purification System for Porous Cement Concrete: Construction and Performance Based on Synergistic Physical Adsorption and Biodegradation
Increased highway traffic has caused a sharp rise in pollutants from service areas, threatening the surrounding water environment. Conventional paving materials cannot balance purification with structural performance, while typical Low Impact Development (LID) techniques require large land areas, hindering efficient pollutant degradation in parking and refueling zones. To address this, an integrated “Graded Porous Cement Concrete (PC) Pavement–Roadside Cascade Purification System (CPS)” is proposed, using a synergistic “physical filtration/adsorption – biodegradation/absorption” pathway. Experimental results show: (1) Short-term operation achieved near-complete removal (≈100%) of Total Phosphorus (TP), Suspended Solids (SS), and heavy metals, with initial Total Nitrogen (TN) and Chemical Oxygen Demand (COD) removal rates of 76.8% and 61.9%, respectively. (2) The system demonstrated sustained capacity. After seven cycles (simulating three months of runoff), TN and TP removal rates remained at 58.8% and 41.1%. Using a COD removal rate of 10% as a failure threshold, performance was effectively restored by rinsing and replacing activated carbon. (3) Micro-characterization (SEM-EDS, FTIR, XRD) revealed that removal occurs through synergistic physical filtration/adsorption, chemical ion exchange, and biodegradation/absorption. This study provides a technically, economically, and operationally feasible integrated solution for highway service area runoff pollution control.
- Open Access
Performance Evolution of Rubber–Plastic-Based Elastomer-Modified Asphalt Under Different Aging Conditions
To reveal the long-term anti-aging mechanisms of rubber–plastic elastomer-modified asphalt in complex service environments and overcome the inherent defects of single polymer modifiers—namely their susceptibility to degradation or phase separation—this study prepared styrene-butadiene-styrene (SBS), low Mooney rubber (LMMR), and low-density polyethylene (LDPE)-modified asphalts. Simultaneously, an LMMR-LDPE rubber–plastic thermoplastic elastomer (TPE) was fabricated utilizing twin-screw extrusion technology and subsequently used to prepare a composite-modified asphalt. Three aging protocols were simulated: short-term thermo-oxidative aging (RTFOT), long-term pressure aging (PAV), and ultraviolet light aging (UV). A multi-scale quantitative characterization was conducted using a dynamic shear rheometer, Fourier transform infrared spectroscopy, and atomic force microscopy to evaluate the rutting factor, carbonyl index, and surface microroughness of each system before and after aging. The experimental results indicate that the coupled effect of long-term stress and thermal oxidation causes the most severe damage to the colloidal structure of modified asphalt. Conventional SBS-modified asphalt, due to its abundance of unsaturated double bonds, exhibits a sharp increase in the carbonyl index and aging index of the rutting factor after aging, making it highly susceptible to oxidative chain scission. Although LDPE-modified asphalt possesses chemical inertness, it is prone to crystalline phase separation under aging conditions, resulting in a microroughness distortion rate of up to 86.36%. In contrast, the LMMR-LDPE composite system, leveraging the high chemical stability of the saturated aliphatic carbon chain and the flexibility-enhancing and crystallization-inhibiting effects of LMMR, effectively reduces active oxidation sites and improves interfacial compatibility. This composite system exhibits the lowest carbonyl increment and rheological attenuation under all aging conditions, while effectively inhibiting the free migration and agglomeration of macromolecular components. The LMMR-LDPE composite modification technology effectively overcomes the inherent drawbacks of single polymers, such as susceptibility to degradation or segregation, demonstrating excellent long-term macroscopic rheological stability and microscopic phase morphology anti-aging capability. The present findings provide laboratory-scale mechanistic support for the design of durable rubber–plastic-modified asphalt systems, while further pilot-scale, economic, and field validation is still required before practical engineering application can be fully assessed.
Open AccessPerformance Evolution of Rubber–Plastic-Based Elastomer-Modified Asphalt Under Different Aging Conditions
To reveal the long-term anti-aging mechanisms of rubber–plastic elastomer-modified asphalt in complex service environments and overcome the inherent defects of single polymer modifiers—namely their susceptibility to degradation or phase separation—this study prepared styrene-butadiene-styrene (SBS), low Mooney rubber (LMMR), and low-density polyethylene (LDPE)-modified asphalts. Simultaneously, an LMMR-LDPE rubber–plastic thermoplastic elastomer (TPE) was fabricated utilizing twin-screw extrusion technology and subsequently used to prepare a composite-modified asphalt. Three aging protocols were simulated: short-term thermo-oxidative aging (RTFOT), long-term pressure aging (PAV), and ultraviolet light aging (UV). A multi-scale quantitative characterization was conducted using a dynamic shear rheometer, Fourier transform infrared spectroscopy, and atomic force microscopy to evaluate the rutting factor, carbonyl index, and surface microroughness of each system before and after aging. The experimental results indicate that the coupled effect of long-term stress and thermal oxidation causes the most severe damage to the colloidal structure of modified asphalt. Conventional SBS-modified asphalt, due to its abundance of unsaturated double bonds, exhibits a sharp increase in the carbonyl index and aging index of the rutting factor after aging, making it highly susceptible to oxidative chain scission. Although LDPE-modified asphalt possesses chemical inertness, it is prone to crystalline phase separation under aging conditions, resulting in a microroughness distortion rate of up to 86.36%. In contrast, the LMMR-LDPE composite system, leveraging the high chemical stability of the saturated aliphatic carbon chain and the flexibility-enhancing and crystallization-inhibiting effects of LMMR, effectively reduces active oxidation sites and improves interfacial compatibility. This composite system exhibits the lowest carbonyl increment and rheological attenuation under all aging conditions, while effectively inhibiting the free migration and agglomeration of macromolecular components. The LMMR-LDPE composite modification technology effectively overcomes the inherent drawbacks of single polymers, such as susceptibility to degradation or segregation, demonstrating excellent long-term macroscopic rheological stability and microscopic phase morphology anti-aging capability. The present findings provide laboratory-scale mechanistic support for the design of durable rubber–plastic-modified asphalt systems, while further pilot-scale, economic, and field validation is still required before practical engineering application can be fully assessed.
- Open Access
- 2 April 2026
- Published by Elsevier in SSRN Electronic Journal
An Integrated Pavement-Roadside Cascade Purification System for Porous Cement Concrete
Increased highway traffic has elevated pollutant loads from service areas, endangering adjacent water environments. Conventional pavements lack integrated purification and structural capacity, while standard Low Impact Development (LID) practices require extensive land, limiting their use in space-constrained zones. Here, we propose a coupled ”Graded Porous Concrete Pavement–Cascade Purification System” leveraging synergistic physical filtration, adsorption, and biodegradation. Short-term operation achieved near-complete removal (~100%) of total phosphorus (TP), suspended solids, and heavy metals, with initial total nitrogen (TN) and chemical oxygen demand (COD) removals of 76.8% and 61.9%, respectively. After seven runoff cycles simulating three months, TP and TN removals remained at 58.8% and 41.1%. System efficacy was restored by rinsing and replacing activated carbon upon COD removal dropping to 10%. Micro-analyses (SEM-EDS, FTIR, XRD) confirmed combined removal mechanisms. This integrated solution offers a technically and economically feasible approach for highway service area runoff treatment.
- 2 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAn Integrated Pavement-Roadside Cascade Purification System for Porous Cement Concrete
Increased highway traffic has elevated pollutant loads from service areas, endangering adjacent water environments. Conventional pavements lack integrated purification and structural capacity, while standard Low Impact Development (LID) practices require extensive land, limiting their use in space-constrained zones. Here, we propose a coupled ”Graded Porous Concrete Pavement–Cascade Purification System” leveraging synergistic physical filtration, adsorption, and biodegradation. Short-term operation achieved near-complete removal (~100%) of total phosphorus (TP), suspended solids, and heavy metals, with initial total nitrogen (TN) and chemical oxygen demand (COD) removals of 76.8% and 61.9%, respectively. After seven runoff cycles simulating three months, TP and TN removals remained at 58.8% and 41.1%. System efficacy was restored by rinsing and replacing activated carbon upon COD removal dropping to 10%. Micro-analyses (SEM-EDS, FTIR, XRD) confirmed combined removal mechanisms. This integrated solution offers a technically and economically feasible approach for highway service area runoff treatment.
- 9 January 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 509
Effect of rejuvenators on the comprehensive performance of cold central plant recycled asphalt mixtures
- 9 January 2026
- Published by Elsevier in Construction and Building Materials
- Vol. 509
Effect of rejuvenators on the comprehensive performance of cold central plant recycled asphalt mixtures
- 1 October 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 496
Design a durable and self-luminous pavement surface material by optimizing optical and mechanical performance
- 1 October 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 496
Design a durable and self-luminous pavement surface material by optimizing optical and mechanical performance
- Open Access
- 14 May 2025
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 22
Development of modified balanced mix design method for cold recycled asphalt mixture
- 14 May 2025
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 22
Open AccessDevelopment of modified balanced mix design method for cold recycled asphalt mixture
- 14 February 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 467
Optimal design and validation of double-layer porous asphalt structure based on thin-layer process
- 14 February 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 467
Optimal design and validation of double-layer porous asphalt structure based on thin-layer process
- 28 January 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 464
Polyaryl polymethylene isocyanate/waste engine oil modified asphalt: Performance and modification mechanism
- 28 January 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 464
Polyaryl polymethylene isocyanate/waste engine oil modified asphalt: Performance and modification mechanism