SRShelley Dyan Rawson

Shelley Dyan Rawson

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Shelley Dyan Rawson has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Tailoring the Microstructure of Lamellar Ti3C2Tx MXene Aerogel by Compressive Straining

    by Shelley D. Rawson, Vildan Bayram, Samuel A. McDonald, Pei Yang, Loic Courtois, Yi Guo, Jiaqi Xu, Timothy L. Burnett, Suelen Barg, Philip J. Withers

    Aerogels are attracting increasing interest due to their functional properties, such as lightweight and high porosity, which make them promising materials for energy storage and advanced composites. Compressive deformation allows the nano- and microstructure of lamellar freeze-cast aerogels to be tailored toward the aforementioned applications, where a 3D nanostructure of closely spaced, aligned sheets is desired. Quantitatively characterizing their microstructural evolution during compression is needed to allow optimization of manufacturing, understand in-service structural changes, and determine how aerogel structure relates to functional properties. Herein we have developed methods to quantitatively analyze lamellar aerogel domains, sheet spacing, and sheet orientation in 3D and to track their evolution as a function of increasing compression through synchrotron phase contrast X-ray microcomputed tomography (μCT). The as-cast domains are predominantly aligned with the freezing direction with random orientation in the orthogonal plane. Generally the sheets rotate toward flat and their spacing narrows progressively with increasing compression with negligible lateral strain (zero Poisson’s ratio). This is with the exception of sheets close to parallel with the loading direction (Z), which maintain their orientation and sheet spacing until ∼60% compression, beyond which they exhibit buckling. These data suggest that a single-domain, fully aligned as-cast aerogel is not necessary to produce a post-compression aligned lamellar structure and indicate how the spacing can be tailored as a function of compressive strain. The analysis methods presented herein are applicable to optimizing freeze-casting process and quantifying lamellar microdomain structures generally.


  • Open Access

    Realization of 3D epoxy resin/Ti3C2T x MXene aerogel composites for low-voltage electrothermal heating

    by Pei Yang, Tian Xia, Subrata Ghosh, Jiacheng Wang, Shelley D Rawson, Philip J Withers, Ian A Kinloch, Suelen Barg

    Suitable electrothermal materials with high heating rates at low electric power are highly desirable for de-icing and thermal management applications. Herein, 3D epoxy resin/Ti3C2T x MXene composites are synthesised and shown to be promising candidates for electrothermal heaters where the MXene serves as a nanoheater and the epoxy resin spreads the heat. A unidirectional freeze-casting technique was used to prepare an anisotropic Ti3C2T x aerogel into which epoxy resin was then vacuum infiltrated and cured. The resulting composite showed an excellent Joule heating performance over repeated heating–cooling cycles. A steady-state temperature of 123 °C was obtained by applying a low voltage of 2 V with 5.1 A current, giving a total power output of 6.1 W cm−2. Such epoxy/MXene aerogel composites, prepared by a simple and cost-effective manner, offer a potential alternative to the traditional metal-based and nanocarbon-based electrothermal materials.


  • MXene Tunable Lamellae Architectures for Supercapacitor Electrodes

    by Vildan Bayram, Michael Ghidiu, Jae Jong Byun, Shelley Dyan Rawson, Pei Yang, Samuel A. Mcdonald, Matthew Lindley, Simon M. Fairclough, Sarah J. Haigh, Philip J. Withers, et al.


  • Four-Dimensional Imaging of Soft Tissue and Implanted Biomaterial Mechanics: A Barbed Suture Case Study for Tendon Repair

    by Shelley Dyan Rawson, Tom Shearer, Tristan Lowe, Marie O’bRien, Jason K. F. Wong, Lee Margetts, Sarah H. Cartmell

    Timely, recent developments in X-ray micro-computed tomography (XµCT) imaging such as increased resolution and improved sample preparation are enabling non-destructive time lapse imaging of polymeric biomaterials when implanted in soft tissue, which we demonstrate herein. Imaging the full 3D structure of an implanted biomaterial provides new opportunities to assess micromechanics of the interface between implant and tissues, and how this changes over time as force is applied in load bearing musculoskeletal applications. In this paper we present a case study demonstrating in situ XµCT and FE analysis, using a dynamically loaded barbed suture repair for its novel use in tendon tissue. The aim of this study was to identify the distribution of stress in the suture and tendon as load is applied. The data gained demonstrates clear 3D visualization of micro-scale features in both the tissue and implant in wet conditions. XµCT imaging has revealed, for the first time, pores around the suture, preventing full engagement of all the barbs with the tendon tissue. Subsequent finite element analysis reveals the localized stress and strain, which is not evenly distributed along the suture, or throughout the tissue. This case study demonstrates for the first time a powerful in situ mechanical imaging tool, which could be readily adapted by other laboratories to interrogate and optimize the interface between implanted biomaterials and soft tissue.