Mariusz Kuglarz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Mariusz Kuglarz has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Klaudiusz Grübel
Faculty of Materials, Civil and Environmental Engineering, University of Bielsko-Biala
10 shared publications - Irini Angelidaki
Department of Chemical and Biochemical Engineering, Technical University of Denmark, DK-2800 Kgs. Lyngby, Denmark
7 shared publications - Jolanta Bohdziewicz
Institute of Water and Wastewater Engineering, Silesian Technical University, Gliwice, Poland
6 shared publications - Merlin Alvarado-Morales
Technical University of Denmark
3 shared publications Dimitar Karakashev
Department of Environmental Engineering, Technical University of Denmark, DK-2800 Kongens Lyngby, Denmark
2 shared publicationsIngólfur B. Gunnarsson
Department of Environmental Engineering, Technical University of Denmark, Building 115, DK-2800 Lyngby, Denmark
2 shared publications
Latest Publications
- Open Access
- 27 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (21) , 10641
Influence of UV Lamp Configuration on the Degradation, Transformation Products, and Toxicity of Emerging Contaminants in Rainwater During Photolysis and TiO2 Photocatalysis
This study compared the degradation of twelve emerging organic contaminants in rainwater by direct photolysis and TiO2-assisted heterogeneous photocatalysis using two UV lamp configurations with different emission spectra and wavelength-specific radiant fluxes ranging from 297 to 578 nm. Differences in micropollutant degradation were observed between the two lamp configurations; however, because their wavelength-specific radiant fluxes differed, these effects cannot be attributed exclusively to the spectral distribution of the emitted radiation. The presence of TiO2 increased the degradation of the investigated organic compounds; only for butylated hydroxytoluene (BHT), triallate (TRI) and oxadiazon (ODZ) were higher removal efficiencies observed during direct photolysis. The analysis of the kinetics of the process led to the conclusion that the type of UV lamp affects the rate of decomposition of micropollutants. GC–MS analysis revealed several transformation products, which were tentatively identified by comparison of their EI mass spectra with the NIST 17 mass spectral library. A greater number of transformation products was detected in samples irradiated with the TQ lamp than in those treated with the TQ-Z2 lamp. Toxicological analysis showed that the toxicity of some treated samples increased during irradiation, coinciding with the detection of transformation products. However, the contribution of individual transformation products to the observed toxicity could not be established.
- 27 October 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (21) , 10641
Open AccessInfluence of UV Lamp Configuration on the Degradation, Transformation Products, and Toxicity of Emerging Contaminants in Rainwater During Photolysis and TiO2 Photocatalysis
This study compared the degradation of twelve emerging organic contaminants in rainwater by direct photolysis and TiO2-assisted heterogeneous photocatalysis using two UV lamp configurations with different emission spectra and wavelength-specific radiant fluxes ranging from 297 to 578 nm. Differences in micropollutant degradation were observed between the two lamp configurations; however, because their wavelength-specific radiant fluxes differed, these effects cannot be attributed exclusively to the spectral distribution of the emitted radiation. The presence of TiO2 increased the degradation of the investigated organic compounds; only for butylated hydroxytoluene (BHT), triallate (TRI) and oxadiazon (ODZ) were higher removal efficiencies observed during direct photolysis. The analysis of the kinetics of the process led to the conclusion that the type of UV lamp affects the rate of decomposition of micropollutants. GC–MS analysis revealed several transformation products, which were tentatively identified by comparison of their EI mass spectra with the NIST 17 mass spectral library. A greater number of transformation products was detected in samples irradiated with the TQ lamp than in those treated with the TQ-Z2 lamp. Toxicological analysis showed that the toxicity of some treated samples increased during irradiation, coinciding with the detection of transformation products. However, the contribution of individual transformation products to the observed toxicity could not be established.
- Open Access
- 5 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (24) , 12873
Laser Truncation of Silicon Nanowires Fabricated by Ag-Assisted Chemical Etching for Reliable Electrode Deposition in Solar Cells
Silicon nanowires (SiNWs) fabricated by Ag-assisted metal-assisted chemical etching (MACE) exhibit excellent light-trapping performance, yet their fragile high-aspect-ratio morphology severely limits reliable metallization in photovoltaic devices. Conventional electrode deposition methods often fail on dense SiNW arrays due to poor mechanical stability of the nanowire tips, leading to delamination, inhomogeneous coverage, and high contact resistance. In this work, we introduce a maskless laser-based truncation technique that selectively shortens MACE-derived SiNWs to controlled residual heights of 300–500 nm exclusively within the regions intended for electrode formation, while preserving the full nanowire morphology in active areas. A detailed parametric study of laser power, scanning speed, and pulse repetition frequency allowed the identification of an optimal processing window enabling controlled tip melting without damaging the nanowire roots or the crystalline silicon substrate. High-resolution SEM imaging confirms uniform planarization, well-preserved structural integrity, and the absence of subsurface defects in the laser-processed tracks. Optical reflectance measurements further demonstrate that introducing 2% and 5% truncated surface fractions—corresponding to the minimum and maximum metallized front-grid coverage in industrial Si solar cells—results in only a minimal reflectance increase, preserving the advantageous the light-trapping behavior of the SiNW texture. The proposed laser truncation approach provides a clean, scalable, and industrially compatible route toward creating electrode-ready surfaces on nanostructured silicon, enabling reliable metallization while maintaining optical performance. This method offers strong potential for integration into silicon photovoltaics, photodetectors, and nanoscale electronic and sensing devices.
- 5 December 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (24) , 12873
Open AccessLaser Truncation of Silicon Nanowires Fabricated by Ag-Assisted Chemical Etching for Reliable Electrode Deposition in Solar Cells
Silicon nanowires (SiNWs) fabricated by Ag-assisted metal-assisted chemical etching (MACE) exhibit excellent light-trapping performance, yet their fragile high-aspect-ratio morphology severely limits reliable metallization in photovoltaic devices. Conventional electrode deposition methods often fail on dense SiNW arrays due to poor mechanical stability of the nanowire tips, leading to delamination, inhomogeneous coverage, and high contact resistance. In this work, we introduce a maskless laser-based truncation technique that selectively shortens MACE-derived SiNWs to controlled residual heights of 300–500 nm exclusively within the regions intended for electrode formation, while preserving the full nanowire morphology in active areas. A detailed parametric study of laser power, scanning speed, and pulse repetition frequency allowed the identification of an optimal processing window enabling controlled tip melting without damaging the nanowire roots or the crystalline silicon substrate. High-resolution SEM imaging confirms uniform planarization, well-preserved structural integrity, and the absence of subsurface defects in the laser-processed tracks. Optical reflectance measurements further demonstrate that introducing 2% and 5% truncated surface fractions—corresponding to the minimum and maximum metallized front-grid coverage in industrial Si solar cells—results in only a minimal reflectance increase, preserving the advantageous the light-trapping behavior of the SiNW texture. The proposed laser truncation approach provides a clean, scalable, and industrially compatible route toward creating electrode-ready surfaces on nanostructured silicon, enabling reliable metallization while maintaining optical performance. This method offers strong potential for integration into silicon photovoltaics, photodetectors, and nanoscale electronic and sensing devices.
- Open Access
- 6 March 2023
- Published by MDPI AG in Fermentation
- Vol. 9 (3) , 259
Succinic Production from Source-Separated Kitchen Biowaste in a Biorefinery Concept: Focusing on Alternative Carbon Dioxide Source for Fermentation Processes
This study presents sustainable succinic acid production from the organic fraction of household kitchen wastes, i.e., the organic fraction of household kitchen waste (OFHKW), pretreated with enzymatic hydrolysis (100% cocktail dosage: 62.5% Cellic® CTec2, 31%% β-Glucanase and 6.5% Cellic ® HTec2, cellulase activity of 12.5 FPU/g-glucan). For fermentation, A. succinogenes was used, which consumes CO2 during the process. OFHKW at biomass loading > 20% (dry matter) resulted in a final concentration of fermentable sugars 81–85 g/L and can be treated as a promising feedstock for succinic production. Obtained results state that simultaneous addition of gaseous CO2 and MgCO3 (>20 g/dm3) resulted in the highest sugar conversion (79–81%) and succinic yields (74–75%). Additionally, CH4 content in biogas, used as a CO2 source, increased by 21–22% and reached 91–92% vol. Liquid fraction of source-separated kitchen biowaste and the residue after succinic fermentation were successfully converted into biogas. Results obtained in this study clearly document the possibility of integrated valuable compounds (succinic acid) and energy (biogas) production from the organic fraction of household kitchen wastes (OFHKW).
- 6 March 2023
- Published by MDPI AG in Fermentation
- Vol. 9 (3) , 259
Open AccessSuccinic Production from Source-Separated Kitchen Biowaste in a Biorefinery Concept: Focusing on Alternative Carbon Dioxide Source for Fermentation Processes
This study presents sustainable succinic acid production from the organic fraction of household kitchen wastes, i.e., the organic fraction of household kitchen waste (OFHKW), pretreated with enzymatic hydrolysis (100% cocktail dosage: 62.5% Cellic® CTec2, 31%% β-Glucanase and 6.5% Cellic ® HTec2, cellulase activity of 12.5 FPU/g-glucan). For fermentation, A. succinogenes was used, which consumes CO2 during the process. OFHKW at biomass loading > 20% (dry matter) resulted in a final concentration of fermentable sugars 81–85 g/L and can be treated as a promising feedstock for succinic production. Obtained results state that simultaneous addition of gaseous CO2 and MgCO3 (>20 g/dm3) resulted in the highest sugar conversion (79–81%) and succinic yields (74–75%). Additionally, CH4 content in biogas, used as a CO2 source, increased by 21–22% and reached 91–92% vol. Liquid fraction of source-separated kitchen biowaste and the residue after succinic fermentation were successfully converted into biogas. Results obtained in this study clearly document the possibility of integrated valuable compounds (succinic acid) and energy (biogas) production from the organic fraction of household kitchen wastes (OFHKW).
- 1 April 2019
- Published by Elsevier in Bioresource Technology
- Vol. 278, 82-91
Miscanthus straw as substrate for biosuccinic acid production: Focusing on pretreatment and downstream processing
- 1 April 2019
- Published by Elsevier in Bioresource Technology
- Vol. 278, 82-91
Miscanthus straw as substrate for biosuccinic acid production: Focusing on pretreatment and downstream processing
- 27 February 2019
- Published by Taylor & Francis in Journal of Environmental Science and Health, Part A
- Vol. 54 (7) , 694-700
Improvement of the thermophilic anaerobic digestion and hygienisation of waste activated sludge by synergistic pretreatment
Hybrid disintegration of waste activated sludge (WAS) before the thermophilic anaerobic stabilization of WAS contributes to the intensification of organic compounds decomposition and increases the effectiveness of the anaerobic stabilization process compared to the fermentation of raw WAS. This article investigates the influence of a chemical–thermal pretreatment procedure with the use of NaOH and freezing by the dry ice on WAS. We found that the hybrid pretreatment of WAS causes higher concentration of released organics in the liquid phase (represented here as a change in soluble chemical oxygen demand – SCOD value) in comparison to these disintegration techniques used separately. The use of disintegrated WAS (WASD) as an additional material in the digester chambers impacts (varying on its proportion added), the generation of biogas and its yield. The recorded amount of the produced biogas and biogas yield after 21 days of fermentation increased by 26.6% and 2.7%, respectively (in comparison to blank sample). In addition, it was observed that the hybrid process before anaerobic stabilization contributes to a higher hygienisation of the digested sludge.
- 27 February 2019
- Published by Taylor & Francis in Journal of Environmental Science and Health, Part A
- Vol. 54 (7) , 694-700
Improvement of the thermophilic anaerobic digestion and hygienisation of waste activated sludge by synergistic pretreatment
Hybrid disintegration of waste activated sludge (WAS) before the thermophilic anaerobic stabilization of WAS contributes to the intensification of organic compounds decomposition and increases the effectiveness of the anaerobic stabilization process compared to the fermentation of raw WAS. This article investigates the influence of a chemical–thermal pretreatment procedure with the use of NaOH and freezing by the dry ice on WAS. We found that the hybrid pretreatment of WAS causes higher concentration of released organics in the liquid phase (represented here as a change in soluble chemical oxygen demand – SCOD value) in comparison to these disintegration techniques used separately. The use of disintegrated WAS (WASD) as an additional material in the digester chambers impacts (varying on its proportion added), the generation of biogas and its yield. The recorded amount of the produced biogas and biogas yield after 21 days of fermentation increased by 26.6% and 2.7%, respectively (in comparison to blank sample). In addition, it was observed that the hybrid process before anaerobic stabilization contributes to a higher hygienisation of the digested sludge.
- Open Access
- 1 January 2019
- Published by EJournal Publishing in International Journal of Environmental Science and Development
- Vol. 10 (11) , 362-367
Influence of Carbon Dioxide and Nitrogen Source on Sustainable Production of Succinic Acid from Miscanthus Hydrolysates
- 1 January 2019
- Published by EJournal Publishing in International Journal of Environmental Science and Development
- Vol. 10 (11) , 362-367
Open AccessInfluence of Carbon Dioxide and Nitrogen Source on Sustainable Production of Succinic Acid from Miscanthus Hydrolysates
- Open Access
- 1 December 2018
- Published by Walter de Gruyter GmbH in Ecological Chemistry and Engineering S
- Vol. 25 (4) , 521-536
Integrated Production of Biofuels and Succinic Acid from Biomass after Thermochemical Pretreatments
The aim of this study was to develop an effective thermochemical method for treatment of industrial hemp, in order to increase its bioconversion to biofuels and bio-products. Industrial hemp was subjected to various thermochemical pretreatments using: alkaline (3 % NaOH), oxidative (3 % H2O2 at pH 11.5) and glycerol-based methods (70-90 % of glycerol, 1-3 % NaOH), prior to enzymatic hydrolysis with Cellic® CTec2/Cellic® HTec2 (15 FPU∙g−1 glucan). Innovative pretreatment with glycerol fraction (80 % glycerol content, 2 % NaOH, 12.5 % biomass loading) showed to be superior over commonly used alkaline and oxidative methods with respect to by-products generation and sugar losses. Integrated process of ethanol production from enriched cellulose fraction (172 kg EtOH∙Mg−1 of dry hemp) and succinic production from xylose-rich residue after ethanol fermentation (59 kg∙Mg−1 of dry hemp) allowed to convert about 97 % of sugars released (glucose and xylose) during enzymatic hydrolysis of pre-treated biomass. The present study showed that it is possible to replace 50 % of the costly yeast extract, used during succinic fermentation as nitrogen source, by alternative nitrogen source (rapeseed cakes) without significant deterioration of succinic yield. Pretreatment liquor after lignin precipitation (52 kg∙Mg−1 of biomass treated) exhibited a high biodegradability (92 %) and allowed to produce 420 m3 CH4/Mg VS). Results obtained in this study clearly document the possibility of biofuels (bioethanol, biogas) and bio-chemicals production from industrial hemp, in a biorefinery approach.
- 1 December 2018
- Published by Walter de Gruyter GmbH in Ecological Chemistry and Engineering S
- Vol. 25 (4) , 521-536
Open AccessIntegrated Production of Biofuels and Succinic Acid from Biomass after Thermochemical Pretreatments
The aim of this study was to develop an effective thermochemical method for treatment of industrial hemp, in order to increase its bioconversion to biofuels and bio-products. Industrial hemp was subjected to various thermochemical pretreatments using: alkaline (3 % NaOH), oxidative (3 % H2O2 at pH 11.5) and glycerol-based methods (70-90 % of glycerol, 1-3 % NaOH), prior to enzymatic hydrolysis with Cellic® CTec2/Cellic® HTec2 (15 FPU∙g−1 glucan). Innovative pretreatment with glycerol fraction (80 % glycerol content, 2 % NaOH, 12.5 % biomass loading) showed to be superior over commonly used alkaline and oxidative methods with respect to by-products generation and sugar losses. Integrated process of ethanol production from enriched cellulose fraction (172 kg EtOH∙Mg−1 of dry hemp) and succinic production from xylose-rich residue after ethanol fermentation (59 kg∙Mg−1 of dry hemp) allowed to convert about 97 % of sugars released (glucose and xylose) during enzymatic hydrolysis of pre-treated biomass. The present study showed that it is possible to replace 50 % of the costly yeast extract, used during succinic fermentation as nitrogen source, by alternative nitrogen source (rapeseed cakes) without significant deterioration of succinic yield. Pretreatment liquor after lignin precipitation (52 kg∙Mg−1 of biomass treated) exhibited a high biodegradability (92 %) and allowed to produce 420 m3 CH4/Mg VS). Results obtained in this study clearly document the possibility of biofuels (bioethanol, biogas) and bio-chemicals production from industrial hemp, in a biorefinery approach.
- Open Access
- 14 November 2018
- Published by MDPI AG in Proceedings
- Vol. 6 (1) , 4
Toxicology Classification of Pool Water Quality in Relation to Selected Pollutant Fractions Present in Washings Samples
The aim of the study is to determine the fractional share of organic pollutants in washing samples collected after pressure filter washings. The evaluation of the physicochemical and toxicological quality of raw washings, fractions ® and Artoxkit M. The concentration of TOC in the analyzed samples of the raw washings was ranged from 2.50–11.00 mgC/L. The presented study showed a significant share of the organic pollutants fraction with a molar weight below 300 Da in the examined washings (the TOC was from 0.71 to 1.48 mgC/L). No correlation was observed between the concentration of TOC and the percentage of toxic effect. Screening toxicity tests can be a signal of swimming pool water quality, but they need to be extended with additional test organisms or observations of more morphological parameters of these organisms.
- 14 November 2018
- Published by MDPI AG in Proceedings
- Vol. 6 (1) , 4
Open AccessToxicology Classification of Pool Water Quality in Relation to Selected Pollutant Fractions Present in Washings Samples
The aim of the study is to determine the fractional share of organic pollutants in washing samples collected after pressure filter washings. The evaluation of the physicochemical and toxicological quality of raw washings, fractions ® and Artoxkit M. The concentration of TOC in the analyzed samples of the raw washings was ranged from 2.50–11.00 mgC/L. The presented study showed a significant share of the organic pollutants fraction with a molar weight below 300 Da in the examined washings (the TOC was from 0.71 to 1.48 mgC/L). No correlation was observed between the concentration of TOC and the percentage of toxic effect. Screening toxicity tests can be a signal of swimming pool water quality, but they need to be extended with additional test organisms or observations of more morphological parameters of these organisms.
- 1 October 2018
- Published by Elsevier in Bioresource Technology
- Vol. 265, 191-199
Integrated production of cellulosic bioethanol and succinic acid from rapeseed straw after dilute-acid pretreatment
- 1 October 2018
- Published by Elsevier in Bioresource Technology
- Vol. 265, 191-199
Integrated production of cellulosic bioethanol and succinic acid from rapeseed straw after dilute-acid pretreatment
- Open Access
- 1 March 2017
- Published by Elsevier in Desalination and Water Treatment
- Vol. 69, 35-42
Application of membrane filtration for integrated production of ethanol and carboxylic acids from pre-treated straw
- 1 March 2017
- Published by Elsevier in Desalination and Water Treatment
- Vol. 69, 35-42
Open AccessApplication of membrane filtration for integrated production of ethanol and carboxylic acids from pre-treated straw