Eleonora Balducci
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Eleonora Balducci has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Andrea Morri
Department of Industrial Engineering (DIN), Alma Mater Studiorum – University of Bologna, Bologna, Italy
3 shared publicationsL. Ceschini
3 shared publications- Lorella Ceschini
Department of Industrial Engineering (DIN), Alma Mater Studiorum, University of Bologna, Viale Risorgimento 4, 40136 Bologna, Italy
3 shared publications Alessandro Morri
Department of Industrial Engineering (DIN), Alma Mater Studiorum – University of Bologna, Bologna, Italy
2 shared publicationsS. Messieri
Department of Industrial Engineering, Alma Mater Studiorum University of Bologna, Bologna, Italy
2 shared publicationsAlessandro Ascari
University of Bologna, Bologna, Italy
1 shared publication
Latest Publications
- 1 October 2018
- Published by Elsevier in Engineering Failure Analysis
- Vol. 92, 12-31
Knock induced erosion on Al pistons: Examination of damage morphology and its causes
- 1 October 2018
- Published by Elsevier in Engineering Failure Analysis
- Vol. 92, 12-31
Knock induced erosion on Al pistons: Examination of damage morphology and its causes
- 9 July 2018
- Published by Springer Nature in JOM
- Vol. 70 (11) , 2716-2725
High Temperature Tensile Tests of the Lightweight 2099 and 2055 Al-Cu-Li Alloy: A Comparison
- 9 July 2018
- Published by Springer Nature in JOM
- Vol. 70 (11) , 2716-2725
High Temperature Tensile Tests of the Lightweight 2099 and 2055 Al-Cu-Li Alloy: A Comparison
- 24 July 2017
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 26 (8) , 3802-3812
EN AW-4032 T6 Piston Alloy After High-Temperature Exposure: Residual Strength and Microstructural Features
- 24 July 2017
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 26 (8) , 3802-3812
EN AW-4032 T6 Piston Alloy After High-Temperature Exposure: Residual Strength and Microstructural Features
- 1 April 2017
- Published by Elsevier in Materials & Design
- Vol. 119, 54-64
Thermal stability of the lightweight 2099 Al-Cu-Li alloy: Tensile tests and microstructural investigations after overaging
- 1 April 2017
- Published by Elsevier in Materials & Design
- Vol. 119, 54-64
Thermal stability of the lightweight 2099 Al-Cu-Li alloy: Tensile tests and microstructural investigations after overaging
- 1 January 2017
- Published by Elsevier in Materials & Design
- Vol. 114, 312-325
Experimental observations of engine piston damage induced by knocking combustion
- 1 January 2017
- Published by Elsevier in Materials & Design
- Vol. 114, 312-325
Experimental observations of engine piston damage induced by knocking combustion
- 27 June 2016
- Published by ASME International
Selective Laser Melting of AISI316L: Process Optimization and Mechanical Property Evaluation
The influence of selective laser melting (SLM) process parameters such as laser power, build direction and scan hatch spacing on mechanical properties, microstructures and porosity formation in AISI 316L components is presented. Experimental activities are performed based on a statistical design-of-experiment approach based on a three-factor, two-level experimental plane. Mechanical tests, as well as optical and SEM analyses were carried out to correlate the resulting microstructures and defects to the process parameters. In order to better characterize the process, gas type, gas flux, coater speed and component positioning were also taken into account.
- 27 June 2016
- Published by ASME International
Selective Laser Melting of AISI316L: Process Optimization and Mechanical Property Evaluation
The influence of selective laser melting (SLM) process parameters such as laser power, build direction and scan hatch spacing on mechanical properties, microstructures and porosity formation in AISI 316L components is presented. Experimental activities are performed based on a statistical design-of-experiment approach based on a three-factor, two-level experimental plane. Mechanical tests, as well as optical and SEM analyses were carried out to correlate the resulting microstructures and defects to the process parameters. In order to better characterize the process, gas type, gas flux, coater speed and component positioning were also taken into account.
- 1 January 2015
- Published by Elsevier in Materials Today: Proceedings
- Vol. 2 (10) , 5037-5044
High Temperature Behavior of the EN AW-2618A Piston Alloy Containing 0.12wt% Zr: Influence of Heat Treatment
- 1 January 2015
- Published by Elsevier in Materials Today: Proceedings
- Vol. 2 (10) , 5037-5044
High Temperature Behavior of the EN AW-2618A Piston Alloy Containing 0.12wt% Zr: Influence of Heat Treatment