David Massoubre
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
David Massoubre has a total of 236 co-authors. Here are the top co-authors by number of shared publications:
- Martin D. Dawson
University of Strathclyde
29 shared publications - Zheng Gong
Institute of Semiconductors, Guangdong Academy of Sciences, No. 363 Changxing Road, Tianhe District, Guangzhou 510650, China
25 shared publications Erdan Gu
Institute of Photonics, University of Strathclyde, Glasgow, U.K.
20 shared publications- Jonathan James Donald McKendry
University of Strathclyde
17 shared publications E. Gu
Institute of Photonics, SUPA, University of Strathclyde 1 , 106 Rottenrow, Glasgow G4 0NW, United Kingdom
16 shared publications- I. M. Watson
Institute of Photonics, Department of Physics, University of Strathclyde, Glasgow G1 1RD (UK)
15 shared publications
Latest Publications
- 12 January 2016
- Published by Wiley in Physica Status Solidi (b)
- Vol. 253 (5) , 824-828
Effect of SiC‐on‐Si template residual stress on GaN residual stress and crystal quality
- 12 January 2016
- Published by Wiley in Physica Status Solidi (b)
- Vol. 253 (5) , 824-828
Effect of SiC‐on‐Si template residual stress on GaN residual stress and crystal quality
- Open Access
- 3 December 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 17811
Silicon etching using only Oxygen at high temperature: An alternative approach to Si micro-machining on 150 mm Si wafers
Using a combination of low-pressure oxygen and high temperatures, isotropic and anisotropic silicon (Si) etch rates can be controlled up to ten micron per minute. By varying the process conditions, we show that the vertical-to-lateral etch rate ratio can be controlled from 1:1 isotropic etch to 1.8:1 anisotropic. This simple Si etching technique combines the main respective advantages of both wet and dry Si etching techniques such as fast Si etch rate, stiction-free, and high etch rate uniformity across a wafer. In addition, this alternative O2-based Si etching technique has additional advantages not commonly associated with dry etchants such as avoiding the use of halogens and has no toxic by-products, which improves safety and simplifies waste disposal. Furthermore, this process also exhibits very high selectivity (>1000:1) with conventional hard masks such as silicon carbide, silicon dioxide and silicon nitride, enabling deep Si etching. In these initial studies, etch rates as high as 9.2 μm/min could be achieved at 1150 °C. Empirical estimation for the calculation of the etch rate as a function of the feature size and oxygen flow rate are presented and used as proof of concepts.
- 3 December 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 17811
Open AccessSilicon etching using only Oxygen at high temperature: An alternative approach to Si micro-machining on 150 mm Si wafers
Using a combination of low-pressure oxygen and high temperatures, isotropic and anisotropic silicon (Si) etch rates can be controlled up to ten micron per minute. By varying the process conditions, we show that the vertical-to-lateral etch rate ratio can be controlled from 1:1 isotropic etch to 1.8:1 anisotropic. This simple Si etching technique combines the main respective advantages of both wet and dry Si etching techniques such as fast Si etch rate, stiction-free, and high etch rate uniformity across a wafer. In addition, this alternative O2-based Si etching technique has additional advantages not commonly associated with dry etchants such as avoiding the use of halogens and has no toxic by-products, which improves safety and simplifies waste disposal. Furthermore, this process also exhibits very high selectivity (>1000:1) with conventional hard masks such as silicon carbide, silicon dioxide and silicon nitride, enabling deep Si etching. In these initial studies, etch rates as high as 9.2 μm/min could be achieved at 1150 °C. Empirical estimation for the calculation of the etch rate as a function of the feature size and oxygen flow rate are presented and used as proof of concepts.
- Open Access
- 25 November 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 17026
Vertically Conductive Single-Crystal SiC-Based Bragg Reflector Grown on Si Wafer
Single-crystal silicon carbide (SiC) thin-films on silicon (Si) were used for the fabrication and characterization of electrically conductive distributed Bragg reflectors (DBRs) on 100 mm Si wafers. The DBRs, each composed of 3 alternating layers of SiC and Al(Ga)N grown on Si substrates, show high wafer uniformity with a typical maximum reflectance of 54% in the blue spectrum and a stopband (at 80% maximum reflectance) as large as 100 nm. Furthermore, high vertical electrical conduction is also demonstrated resulting to a density of current exceeding 70 A/cm2 above 1.5 V. Such SiC/III-N DBRs with high thermal and electrical conductivities could be used as pseudo-substrate to enhance the efficiency of SiC-based and GaN-based optoelectronic devices on large Si wafers.
- 25 November 2015
- Published by Springer Nature in Scientific Reports
- Vol. 5 (1) , 17026
Open AccessVertically Conductive Single-Crystal SiC-Based Bragg Reflector Grown on Si Wafer
Single-crystal silicon carbide (SiC) thin-films on silicon (Si) were used for the fabrication and characterization of electrically conductive distributed Bragg reflectors (DBRs) on 100 mm Si wafers. The DBRs, each composed of 3 alternating layers of SiC and Al(Ga)N grown on Si substrates, show high wafer uniformity with a typical maximum reflectance of 54% in the blue spectrum and a stopband (at 80% maximum reflectance) as large as 100 nm. Furthermore, high vertical electrical conduction is also demonstrated resulting to a density of current exceeding 70 A/cm2 above 1.5 V. Such SiC/III-N DBRs with high thermal and electrical conductivities could be used as pseudo-substrate to enhance the efficiency of SiC-based and GaN-based optoelectronic devices on large Si wafers.
- 1 September 2015
- Published by Elsevier in Superlattices and Microstructures
- Vol. 85, 543-550
A method for extraction of electron mobility in power HEMTs
- 1 September 2015
- Published by Elsevier in Superlattices and Microstructures
- Vol. 85, 543-550
A method for extraction of electron mobility in power HEMTs
- 30 June 2015
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 821-823, 205-208
Si Surface Preparation for Heteroepitaxial Growth of SiC Using In Situ Oxidation
To achieve high quality SiC growth on Si substrate, it is essential to get a smooth Si surface without forming SiC and graphitic islands during the surface cleaning and before the carbonisation process. In this paper, a novel in-situ surface cleaning method designed for the hetero-epitaxial growth of SiC on Si substrate is developed using a custom-made low-pressure chemical vapour deposition reactor. The results indicate that the combination of ramping in oxygen and subsequent flowing of SiH4 avoids the contamination of Si, enables the oxide layer to be removed smoothly, and subsequently creates a smooth Si surface with regular atomic steps. SiC grown on off-axis Si has better crystallinity and significantly smaller roughness than that grown on on-axis Si.
- 30 June 2015
- Published by Trans Tech Publications, Ltd. in Materials Science Forum
- Vol. 821-823, 205-208
Si Surface Preparation for Heteroepitaxial Growth of SiC Using In Situ Oxidation
To achieve high quality SiC growth on Si substrate, it is essential to get a smooth Si surface without forming SiC and graphitic islands during the surface cleaning and before the carbonisation process. In this paper, a novel in-situ surface cleaning method designed for the hetero-epitaxial growth of SiC on Si substrate is developed using a custom-made low-pressure chemical vapour deposition reactor. The results indicate that the combination of ramping in oxygen and subsequent flowing of SiH4 avoids the contamination of Si, enables the oxide layer to be removed smoothly, and subsequently creates a smooth Si surface with regular atomic steps. SiC grown on off-axis Si has better crystallinity and significantly smaller roughness than that grown on on-axis Si.
- Open Access
- 10 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 62 (6) , 1918-1925
Active-Matrix GaN Micro Light-Emitting Diode Display With Unprecedented Brightness
Displays based on microsized gallium nitride light-emitting diodes possess extraordinary brightness. It is demonstrated here both theoretically and experimentally that the layout of the n-contact in these devices is important for the best device performance. We highlight, in particular, the significance of a nonthermal increase of differential resistance upon multipixel operation. These findings underpin the realization of a blue microdisplay with a luminance of 10 6 cd/m 2 .
- 10 April 2015
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 62 (6) , 1918-1925
Open AccessActive-Matrix GaN Micro Light-Emitting Diode Display With Unprecedented Brightness
Displays based on microsized gallium nitride light-emitting diodes possess extraordinary brightness. It is demonstrated here both theoretically and experimentally that the layout of the n-contact in these devices is important for the best device performance. We highlight, in particular, the significance of a nonthermal increase of differential resistance upon multipixel operation. These findings underpin the realization of a blue microdisplay with a luminance of 10 6 cd/m 2 .
- 14 January 2014
- Published by Optica Publishing Group in Optics Express
- Vol. 22 (2) , 1372-1380
Optoelectronic tweezers system for single cell manipulation and fluorescence imaging of live immune cells
Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
- 14 January 2014
- Published by Optica Publishing Group in Optics Express
- Vol. 22 (2) , 1372-1380
Optoelectronic tweezers system for single cell manipulation and fluorescence imaging of live immune cells
Optics InfoBase is the Optical Society's online library for flagship journals, partnered and copublished journals, and recent proceedings from OSA conferences.
- 16 December 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 103 (25) , 253302
Nanoscale-accuracy transfer printing of ultra-thin AlInGaN light-emitting diodes onto mechanically flexible substrates
The transfer printing of 2 μm-thick aluminum indium gallium nitride (AlInGaN) micron-size light-emitting diodes with 150 nm (±14 nm) minimum spacing is reported. The thin AlInGaN structures were assembled onto mechanically flexible polyethyleneterephthalate/polydimethylsiloxane substrates in a representative 16 × 16 array format using a modified dip-pen nano-patterning system. Devices in the array were positioned using a pre-calculated set of coordinates to demonstrate an automated transfer printing process. Individual printed array elements showed blue emission centered at 486 nm with a forward-directed optical output power up to 80 μW (355 mW/cm2) when operated at a current density of 20 A/cm2.
- 16 December 2013
- Published by AIP Publishing in Applied Physics Letters
- Vol. 103 (25) , 253302
Nanoscale-accuracy transfer printing of ultra-thin AlInGaN light-emitting diodes onto mechanically flexible substrates
The transfer printing of 2 μm-thick aluminum indium gallium nitride (AlInGaN) micron-size light-emitting diodes with 150 nm (±14 nm) minimum spacing is reported. The thin AlInGaN structures were assembled onto mechanically flexible polyethyleneterephthalate/polydimethylsiloxane substrates in a representative 16 × 16 array format using a modified dip-pen nano-patterning system. Devices in the array were positioned using a pre-calculated set of coordinates to demonstrate an automated transfer printing process. Individual printed array elements showed blue emission centered at 486 nm with a forward-directed optical output power up to 80 μW (355 mW/cm2) when operated at a current density of 20 A/cm2.
- 3 December 2013
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 29 (1)
Micro-structured light emission from planar InGaN light-emitting diodes
- 3 December 2013
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 29 (1)
Micro-structured light emission from planar InGaN light-emitting diodes
- Open Access
- 17 September 2013
- Published by Wiley in Laser & Photonics Reviews
- Vol. 7 (6) , 1065-1078
Micro‐LED pumped polymer laser: A discussion of future pump sources for organic lasers
Optical pumping conditions for organic solid‐state lasers (OSLs) are discussed with particular emphasis on the use of gallium nitride based light‐emitting diodes (LEDs) as pump sources. LEDs operate in a regime where the pump should be optimized for a short rise time and high peak intensity, whereas fall time and overall pulse duration are less important. Lasers pumped with this approach need to have very low thresholds which can now be routinely created using (one‐dimensional) distributed feedback lasers. In this particular case stripe‐shaped excitation with linearly polarized light is beneficial. Arrays of micron‐sized flip‐chip LEDs have been arranged in an appropriate stripe shape and the array dimensions were chosen such that the divergence of LED emission does not cause a loss in peak intensity. These micro‐LED arrays have successfully been used to pump OSLs with thresholds near 300 W/cm2 (∼9 ns rise time, 35 ns pulse duration), paving the way for compact arrays of indirectly electrically pumped OSLs.
- 17 September 2013
- Published by Wiley in Laser & Photonics Reviews
- Vol. 7 (6) , 1065-1078
Open AccessMicro‐LED pumped polymer laser: A discussion of future pump sources for organic lasers
Optical pumping conditions for organic solid‐state lasers (OSLs) are discussed with particular emphasis on the use of gallium nitride based light‐emitting diodes (LEDs) as pump sources. LEDs operate in a regime where the pump should be optimized for a short rise time and high peak intensity, whereas fall time and overall pulse duration are less important. Lasers pumped with this approach need to have very low thresholds which can now be routinely created using (one‐dimensional) distributed feedback lasers. In this particular case stripe‐shaped excitation with linearly polarized light is beneficial. Arrays of micron‐sized flip‐chip LEDs have been arranged in an appropriate stripe shape and the array dimensions were chosen such that the divergence of LED emission does not cause a loss in peak intensity. These micro‐LED arrays have successfully been used to pump OSLs with thresholds near 300 W/cm2 (∼9 ns rise time, 35 ns pulse duration), paving the way for compact arrays of indirectly electrically pumped OSLs.