Wenmei Zhang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Wenmei Zhang has a total of 115 co-authors. Here are the top co-authors by number of shared publications:
- Xinwei Chen
Shanxi University
26 shared publications - Liping Han
College of Physics and Electronic Engineering Shanxi University Taiyuan China
21 shared publications - Runbo Ma
Shanxi University
16 shared publications - Guorui Han
School of Physics and Electronic Engineering, Shanxi University, Shanxi, China
15 shared publications Liping Han
College of Physics and Electronics Engineering, Shanxi University, Taiyuan, China
15 shared publications- Rongcao Yang
School of Physics and Electronics Engineering Shanxi University Taiyuan China
13 shared publications
Latest Publications
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (8) , 11871-11879
Design of an Asymmetric Double-Sided Microwave Dielectric Sensor Based on ELC-CSRR Composite Structure
This paper proposes an asymmetric double-sided microwave sensor suitable for permittivity detection of general materials. The front side of the sensor is loaded with an improved Electric-LC resonator to realize the sensing function, while the back side is integrated with a Complementary Split-Ring Resonator as a reference resonator. The CSRR not only provides a stable reference frequency but also deepens the amplitude dip of the transmission zero induced by the ELC, thereby improving the detection capability for high-loss materials. To ensure the stability of the reference frequency, decoupling between the ELC and CSRR is achieved through vertical isolation and horizontal misalignment. An equivalent circuit model of the sensor is established, and the working principle as well as the performance enhancement mechanism are systematically explained through theoretical derivation. Both simulated and experimental results demonstrate that the sensor achieves a relative sensitivity of 5.2% within a compact detection area of 22 mm × 15 mm.
- 1 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 26 (8) , 11871-11879
Design of an Asymmetric Double-Sided Microwave Dielectric Sensor Based on ELC-CSRR Composite Structure
This paper proposes an asymmetric double-sided microwave sensor suitable for permittivity detection of general materials. The front side of the sensor is loaded with an improved Electric-LC resonator to realize the sensing function, while the back side is integrated with a Complementary Split-Ring Resonator as a reference resonator. The CSRR not only provides a stable reference frequency but also deepens the amplitude dip of the transmission zero induced by the ELC, thereby improving the detection capability for high-loss materials. To ensure the stability of the reference frequency, decoupling between the ELC and CSRR is achieved through vertical isolation and horizontal misalignment. An equivalent circuit model of the sensor is established, and the working principle as well as the performance enhancement mechanism are systematically explained through theoretical derivation. Both simulated and experimental results demonstrate that the sensor achieves a relative sensitivity of 5.2% within a compact detection area of 22 mm × 15 mm.
- 24 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (6) , 5504-5514
Multipolarization Array Antenna With Adjustable Beam Based on Catenary Metasurface
In this paper, a multi-polarization array antenna based on the catenary metasurface (MS) is proposed. The catenary MS unit provides continuous phase coverage of 2π through its inherent geometric curvature and can convert linearly polarized (LP) waves into left-hand (LHCP) and right‑hand circularly polarized (RHCP) waves. Employing it, a dual-CP element that simultaneously radiates LHCP and RHCP beams is designed. It achieves an efficiency of 65% in dimensions of 88 × 88 × 2 mm3. Further, by integrating a reconfigurable feed network, a 2 × 2 multi-polarization array antenna is implemented in a low profile. The results indicate that the realized antenna can radiate multi-polarized waves assembled by different LP/LHCP/RHCP wave through controlling PIN diodes to select different subarrays. Also, beam directions can be adjusted. When activating a single PIN diode, the array achieves a 3 dB axial ratio bandwidth (ARBW) of 1.7% and a peak gain of 10.3 dBi at 6 GHz. The proposed antenna design demonstrates compact size, real-time polarization control and wavefront reconfigurability, making it suitable for adaptive wireless and satellite applications.
- 24 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 74 (6) , 5504-5514
Multipolarization Array Antenna With Adjustable Beam Based on Catenary Metasurface
In this paper, a multi-polarization array antenna based on the catenary metasurface (MS) is proposed. The catenary MS unit provides continuous phase coverage of 2π through its inherent geometric curvature and can convert linearly polarized (LP) waves into left-hand (LHCP) and right‑hand circularly polarized (RHCP) waves. Employing it, a dual-CP element that simultaneously radiates LHCP and RHCP beams is designed. It achieves an efficiency of 65% in dimensions of 88 × 88 × 2 mm3. Further, by integrating a reconfigurable feed network, a 2 × 2 multi-polarization array antenna is implemented in a low profile. The results indicate that the realized antenna can radiate multi-polarized waves assembled by different LP/LHCP/RHCP wave through controlling PIN diodes to select different subarrays. Also, beam directions can be adjusted. When activating a single PIN diode, the array achieves a 3 dB axial ratio bandwidth (ARBW) of 1.7% and a peak gain of 10.3 dBi at 6 GHz. The proposed antenna design demonstrates compact size, real-time polarization control and wavefront reconfigurability, making it suitable for adaptive wireless and satellite applications.
- 23 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (12) , 4850-4854
Dual-Beam Power Allocation Transmitarray Antenna Based on Independently Regulated Copolarized Amplitude/Phase Metasurface
In this letter, a transmissive metasurface (MS) with independently regulated co-polarized amplitude and phase is proposed. The unit of MS is composed of four metal layers printed on two substrates. The co-polarized transmission phase and amplitude are adjusted by double-split ring resonator (DSRR1) and DSRR2 surrounding the circular patch, respectively. By adjusting the opening angle of DSRR1, a wide phase coverage range of 333° is achieved. Additionally, by rotating DSRR2, continuous amplitude control is attained while maintaining a constant transmission phase. The DSRR1 and DSRR2 are placed on same metal layers and circular patches are placed in each metal layer to decouple the amplitude and phase modulation. Besides, the proposed MS manipulate the co-polarized wave without the need for polarized gratings. Thus, the number of substrate layer is reduced compared to other reported multi-layer co-polarized transmissive units. To demonstrate its characteristics, we design a transmitarray antenna for power allocation that can generate dual beams with power ratios of 2:1 or 1:1. Finally, a prototype with 2:1 power ratio is fabricated and measured. Its beams are directed at (θ = 10°, ϕ = 0°) and (θ = 25°, ϕ = 90°). The measured results are consistent with the designed goals and the aperture efficiency (AE) can reach 25.13%.
- 23 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (12) , 4850-4854
Dual-Beam Power Allocation Transmitarray Antenna Based on Independently Regulated Copolarized Amplitude/Phase Metasurface
In this letter, a transmissive metasurface (MS) with independently regulated co-polarized amplitude and phase is proposed. The unit of MS is composed of four metal layers printed on two substrates. The co-polarized transmission phase and amplitude are adjusted by double-split ring resonator (DSRR1) and DSRR2 surrounding the circular patch, respectively. By adjusting the opening angle of DSRR1, a wide phase coverage range of 333° is achieved. Additionally, by rotating DSRR2, continuous amplitude control is attained while maintaining a constant transmission phase. The DSRR1 and DSRR2 are placed on same metal layers and circular patches are placed in each metal layer to decouple the amplitude and phase modulation. Besides, the proposed MS manipulate the co-polarized wave without the need for polarized gratings. Thus, the number of substrate layer is reduced compared to other reported multi-layer co-polarized transmissive units. To demonstrate its characteristics, we design a transmitarray antenna for power allocation that can generate dual beams with power ratios of 2:1 or 1:1. Finally, a prototype with 2:1 power ratio is fabricated and measured. Its beams are directed at (θ = 10°, ϕ = 0°) and (θ = 25°, ϕ = 90°). The measured results are consistent with the designed goals and the aperture efficiency (AE) can reach 25.13%.
- 17 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (12) , 10241-10249
Dual-Band Energy-Selective Surface With Wide Absorption Band
A dual-band energy-selective surface (ESS) that achieves stealth for in-band and out-of-band electromagnetic (EM) waves is proposed in this article. It consists of an absorptive layer and a switchable layer. The absorptive layer integrates cross-shaped and gear-shaped metal patches loaded with resistors and p-i-n diodes. The switchable layer uses double concentric ring slots embedded with diodes. Compared with existing ESSs, the proposed ESS controls the absorption band by integrating diodes in the absorption layer. Furthermore, high-power microwaves (HPMs) inside and outside the passbands are absorbed. The experimental results demonstrate that the ESS exhibits the insertion loss (IL) of 0.8 dB at 3.76 and 5.86 GHz when the low-power signal is incident. The out-of-band absorption bands range from 1.81 to 3.43 GHz and from 4.1 to 5.59 GHz. Under HPM, the shielding effectiveness (SE) is more than 10 dB in the range of 1–6.3 GHz. Also, the relative bandwidth of the absorption band reaches 108% (1.86–6.3 GHz). By integrating HPM shielding, wideband absorption, and dual-band operation, this ESS shows significant application prospects in EM compatibility and stealth technologies.
- 17 September 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (12) , 10241-10249
Dual-Band Energy-Selective Surface With Wide Absorption Band
A dual-band energy-selective surface (ESS) that achieves stealth for in-band and out-of-band electromagnetic (EM) waves is proposed in this article. It consists of an absorptive layer and a switchable layer. The absorptive layer integrates cross-shaped and gear-shaped metal patches loaded with resistors and p-i-n diodes. The switchable layer uses double concentric ring slots embedded with diodes. Compared with existing ESSs, the proposed ESS controls the absorption band by integrating diodes in the absorption layer. Furthermore, high-power microwaves (HPMs) inside and outside the passbands are absorbed. The experimental results demonstrate that the ESS exhibits the insertion loss (IL) of 0.8 dB at 3.76 and 5.86 GHz when the low-power signal is incident. The out-of-band absorption bands range from 1.81 to 3.43 GHz and from 4.1 to 5.59 GHz. Under HPM, the shielding effectiveness (SE) is more than 10 dB in the range of 1–6.3 GHz. Also, the relative bandwidth of the absorption band reaches 108% (1.86–6.3 GHz). By integrating HPM shielding, wideband absorption, and dual-band operation, this ESS shows significant application prospects in EM compatibility and stealth technologies.
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (6) , 4158-4163
Wideband RCS Reduction of Dual-Band Fabry-Perot Cavity Antenna Using Pancharatnam-Berry Phase Coding Metasurface and AMC Surface
In this communication, we propose a dual-band Fabry–Perot (F-P) cavity antenna with a wideband low radar cross section (RCS) by integrating a Pancharatnam–Berry phase coding metasurface (PBPCM) and artificial magnetic conductor (AMC) surfaces. This antenna comprises two partially reflective surfaces (PRSs) that form two nested F-P cavities for signal in two bands. To reduce the monostatic RCS at high frequencies, a PBPCM is placed on the top side of the upper PRS, leveraging its ability to redirect reflected waves into different directions by encoding the phase on the metasurface. Additionally, two AMC surfaces etched on the top side of both the lower PRS and the ground plane further reduce the low-frequency RCS through phase cancellation. The overall antenna profile is also minimized owing to the AMC’s flexible phase adjustment. The simulated and measured results verify the feasibility of the proposed method. The prototyped F-P cavity antenna exhibits a measured −10 dB impedance bandwidth of 4.15-4.8 and 7.8–8.4 GHz, with peak gains of 10 dBi at 4.45 GHz and 15.9 dBi at 8.3 GHz, respectively. Moreover, a wideband RCS-reduction bandwidth from 3 to 16 GHz is achieved under both x- and y-polarizations.
- 3 March 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Antennas and Propagation
- Vol. 73 (6) , 4158-4163
Wideband RCS Reduction of Dual-Band Fabry-Perot Cavity Antenna Using Pancharatnam-Berry Phase Coding Metasurface and AMC Surface
In this communication, we propose a dual-band Fabry–Perot (F-P) cavity antenna with a wideband low radar cross section (RCS) by integrating a Pancharatnam–Berry phase coding metasurface (PBPCM) and artificial magnetic conductor (AMC) surfaces. This antenna comprises two partially reflective surfaces (PRSs) that form two nested F-P cavities for signal in two bands. To reduce the monostatic RCS at high frequencies, a PBPCM is placed on the top side of the upper PRS, leveraging its ability to redirect reflected waves into different directions by encoding the phase on the metasurface. Additionally, two AMC surfaces etched on the top side of both the lower PRS and the ground plane further reduce the low-frequency RCS through phase cancellation. The overall antenna profile is also minimized owing to the AMC’s flexible phase adjustment. The simulated and measured results verify the feasibility of the proposed method. The prototyped F-P cavity antenna exhibits a measured −10 dB impedance bandwidth of 4.15-4.8 and 7.8–8.4 GHz, with peak gains of 10 dBi at 4.45 GHz and 15.9 dBi at 8.3 GHz, respectively. Moreover, a wideband RCS-reduction bandwidth from 3 to 16 GHz is achieved under both x- and y-polarizations.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Chipless RFID Sensor Detecting the Angle and Width of Crack in the Metal With High Sensitivity
In this paper, a metal crack sensor based on chipless RFID technology is proposed. It is used to monitor the angle and width of cracks in the internet of things (IoT). The sensor is composed of square, rectangular and bow-tie patches and operate within the frequency range of 3.5-7 GHz. By using polarization multiplexing and a modified bow-tie patch, the sensitivity of the sensor is improved. The results show that the sensor can accurately identify the cracks along the directions of 0°, 45°, 90° and 135°. The corresponding sensitivity in each direction is 50.20 MHz/0.1 mm, 23.50 MHz/0.1 mm, 50.41 MHz/0.1 mm, and 33.88 MHz/0.1 mm. The sensor has the characteristics of passive, low-cost and simple structure.
- 26 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-8
Chipless RFID Sensor Detecting the Angle and Width of Crack in the Metal With High Sensitivity
In this paper, a metal crack sensor based on chipless RFID technology is proposed. It is used to monitor the angle and width of cracks in the internet of things (IoT). The sensor is composed of square, rectangular and bow-tie patches and operate within the frequency range of 3.5-7 GHz. By using polarization multiplexing and a modified bow-tie patch, the sensitivity of the sensor is improved. The results show that the sensor can accurately identify the cracks along the directions of 0°, 45°, 90° and 135°. The corresponding sensitivity in each direction is 50.20 MHz/0.1 mm, 23.50 MHz/0.1 mm, 50.41 MHz/0.1 mm, and 33.88 MHz/0.1 mm. The sensor has the characteristics of passive, low-cost and simple structure.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (4) , 1003-1007
Low Sidelobe Dual-Beam Metasurface Antenna Based on Taylor Distribution and Digital Filtering Methods
The Taylor distribution is often used to design low sidelobe level (SLL) antennas. While using this method to reduce SLL, it also leads to gain loss. To overcome this drawback, a method combining Taylor distribution with dual median and Gaussian filtering is proposed in this letter. First, the Taylor distribution modified with an amplitude compensation matrix is adopted to reduce the SLL when using uniform distribution. Then, an innovative dual filtering strategy is introduced, which uses median filtering to suppress the SLL and Gaussian filtering to mitigate the gain loss. Finally, by finely readjusting the unit amplitudes according to phases, optimized performance is achieved. According to these steps, a dual-beam antenna is designed, fabricated and measured, which has a low SLL of -28.91 dB and a high gain of 16.6 dBi at 10 GHz. Compared with the metasurface antenna using only phase modulation, the SLL is reduced by 7.6 dB, while the gain is just decreased by 0.3 dBi.
- 30 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (4) , 1003-1007
Low Sidelobe Dual-Beam Metasurface Antenna Based on Taylor Distribution and Digital Filtering Methods
The Taylor distribution is often used to design low sidelobe level (SLL) antennas. While using this method to reduce SLL, it also leads to gain loss. To overcome this drawback, a method combining Taylor distribution with dual median and Gaussian filtering is proposed in this letter. First, the Taylor distribution modified with an amplitude compensation matrix is adopted to reduce the SLL when using uniform distribution. Then, an innovative dual filtering strategy is introduced, which uses median filtering to suppress the SLL and Gaussian filtering to mitigate the gain loss. Finally, by finely readjusting the unit amplitudes according to phases, optimized performance is achieved. According to these steps, a dual-beam antenna is designed, fabricated and measured, which has a low SLL of -28.91 dB and a high gain of 16.6 dBi at 10 GHz. Compared with the metasurface antenna using only phase modulation, the SLL is reduced by 7.6 dB, while the gain is just decreased by 0.3 dBi.
- 27 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (2) , 514-518
Design and Synthesis of a High-Selectivity and Wide Stopband Suppression Filtering Antenna With Symmetric Coupling Structure
A fourth-order high selectivity and wide stopband suppression filtering antenna with symmetric coupling structure is presented. By incorporating resonant units with different structures, harmonics are effectively suppressed due to the resonators' identical fundamental mode and distinct second-order harmonics. By introducing of a cross-coupling path, two controllable radiation nulls are achieved, further enhancing the antenna's selectivity. Additionally, the symmetric coupling structure is employed to minimize cross-polarization. Finally, the theory of coupling matrix is utilized in the synthesis of filtering antenna, and the relevant physical parameters are obtained. The results demonstrate that the proposed filtering antenna exhibits a bandwidth of 2.40-2.66 GHz for |S11|<-10 dB, a peak gain of 6.1 dBi, and two radiation nulls at 1.98 and 3.12 GHz, resulting in enhanced selectivity with suppression levels exceeding 37.5 dB and cross-polarization levels below -38.1 dB.
- 27 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (2) , 514-518
Design and Synthesis of a High-Selectivity and Wide Stopband Suppression Filtering Antenna With Symmetric Coupling Structure
A fourth-order high selectivity and wide stopband suppression filtering antenna with symmetric coupling structure is presented. By incorporating resonant units with different structures, harmonics are effectively suppressed due to the resonators' identical fundamental mode and distinct second-order harmonics. By introducing of a cross-coupling path, two controllable radiation nulls are achieved, further enhancing the antenna's selectivity. Additionally, the symmetric coupling structure is employed to minimize cross-polarization. Finally, the theory of coupling matrix is utilized in the synthesis of filtering antenna, and the relevant physical parameters are obtained. The results demonstrate that the proposed filtering antenna exhibits a bandwidth of 2.40-2.66 GHz for |S11|<-10 dB, a peak gain of 6.1 dBi, and two radiation nulls at 1.98 and 3.12 GHz, resulting in enhanced selectivity with suppression levels exceeding 37.5 dB and cross-polarization levels below -38.1 dB.
- 22 October 2024
- Published by Taylor & Francis in Electromagnetics
- Vol. 44 (8) , 604-613
Full-space trifunctional metasurface with independent amplitude/phase control and its application to asymmetric spatial power divider
- 22 October 2024
- Published by Taylor & Francis in Electromagnetics
- Vol. 44 (8) , 604-613
Full-space trifunctional metasurface with independent amplitude/phase control and its application to asymmetric spatial power divider