GHGuoqiang Han

Guoqiang Han

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Guoqiang Han has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Adaptive Compressive Sensing Imaging in AFM Based on Target Block Detection

    by Yongheng Zeng, Yongjian Chen, Teng Wu, Guoqiang Han

    Atomic force microscopy (AFM) is essential for studying the surface properties of samples at the micro‐ and nanoscales. Traditional AFM scanning methods are time‐consuming, particularly for obtaining high‐resolution images. Compressive sensing (CS) has been utilized for fast AFM imaging. However, as the size and resolution requirements of the images increase, the measurement matrix for compressive sensing also becomes larger. Block compressive sensing (BCS) divides the image into blocks and reconstructs them with a small measurement matrix, but it is difficult to balance the imaging quality between regions. Therefore, we propose an innovative adaptive CS‐AFM imaging scheme. A low‐resolution image is obtained through fast scanning, and a high‐resolution image is generated using bicubic interpolation. The Otsu and eight‐connectivity methods detect the location of the target blocks, while the GRNN model adapts the sampling rate for it. A supplementary scan is performed on the target block, followed by reconstruction using the TVAL3 algorithm. Finally, the target region is replaced with the reconstructed high‐quality target blocks. Compared to other schemes, the results demonstrate that our method excels in achieving fast, high‐quality, and high‐resolution imaging.


  • Open Access

    Adaptive compressive sensing imaging in AFM based on target block detection

    by Yongheng Zeng, Yongjian Chen, Teng Wu, Guoqiang Han

    Atomic force microscopy (AFM) is essential for studying the surface properties of samples at the micro- and nanoscales. Traditional AFM scanning methods are time-consuming, particularly for obtaining high-resolution images. Compressive sensing (CS) has been utilized for fast AFM imaging. However, as the size and resolution requirements of the images increase, the measurement matrix for compressive sensing also becomes larger. Block compressive sensing (BCS) divides the image into blocks and reconstructs them with a small measurement matrix, but it is difficult to balance the imaging quality between regions. Therefore, we propose an innovative adaptive CS-AFM imaging scheme. A low-resolution image is obtained through fast scanning, and a high-resolution image is generated using bicubic interpolation. The Otsu and eight-connectivity methods detect the location of the target blocks, while the GRNN model adapts the sampling rate for it. Supplementary scan is performed on the target block, followed by reconstruction using the TVAL3 algorithm. Finally, the target region is replaced with the reconstructed high-quality target blocks. Compared to other schemes, the results demonstrate that our method excels in achieving fast, high-quality, and high-resolution imaging.

  • Adaptive block imaging based on compressive sensing in AFM

    by Yuchuan Zhang, Yongjian Chen, Teng Wu, Guoqiang Han

    Atomic force microscopy (AFM) is a kind of high‐precision instrument to measure the surface morphology of various conductive or nonconductive samples. However, obtaining a high‐resolution image with standard AFM scanning requires more time. Using block compressive sensing (BCS) is an effective approach to achieve rapid AFM imaging. But, the routine BCS‐AFM imaging is difficult to balance the image quality of each local area. It is easy to lead to excessive sampling in some flat areas, resulting in time‐consuming. At the same time, there is a lack of sampling in some areas with significant details, resulting in poor imaging quality. Thus, an innovative adaptive BCS‐AFM imaging method is proposed. The overlapped block is used to eliminate blocking artifacts. Characteristic parameters (GTV, Lu, and SD) are used to predict the local morphological characteristics of the samples. Back propagation neural network is employed to acquire the appropriate sampling rate of each sub‐block. Sampling points are obtained by pre‐scanning and adaptive supplementary scanning. Afterward, all sub‐block images are reconstructed using the TVAL3 algorithm. Each sample is capable of achieving uniform, excellent image quality. Image visual effects and evaluation indicators (PSNR and SSIM) are employed for the purpose of evaluating and analyzing the imaging effects of samples. Compared with two nonadaptive and two other adaptive imaging schemes, our proposed scheme has the characteristics of a high degree of automation, uniformly high‐quality imaging, and rapid imaging speed.Highlights: The proposed adaptive BCS method can address the issues of uneven image quality and slow imaging speed in AFM. The appropriate sampling rate of each sub‐block of the sample can be obtained by BP neural network. The introduction of GTV, Lu, and SD can effectively reveal the morphological features of AFM images. Seven samples with different morphology are used to test the performance of the proposed adaptive algorithm. Practical experiments are carried out with two samples to verify the feasibility of the proposed adaptive algorithm.


  • Open Access

    Image reconstruction of TGZ3 grating by eliminating tip‐sample convolution effect in AFM

    by Teng Wu, Luyao Lv, Yu Zou, Guoqiang Han

    Accurate and meticulous measurement is an important prerequisite to obtain the real surface information of samples in atomic force microscopy (AFM). A severe problem is the frequent occurrence of measurement errors, which are mainly caused by the nonlinearity of the probe driver, the temperature drift of the system and the tip characteristics. The measurement errors caused by probe tip are the main source of errors in AFM nanoscale measurements. The shape and state of AFM tip will distort the AFM image from the actual sample morphology. If the information about the probe is known, the measurement error caused by the probe tip can be greatly reduced. In order to obtain accurate AFM images, a new method based on geometric measurement model and blind tip reconstruction is proposed to eliminate tip‐sample convolution in the measurement of grating samples. The static and dynamic characteristics of the AFM tip are described by four parameters: cone angle, curvature radius, scanning inclination angle and mounting inclination angle. Finally, the feasibility and effectiveness of the new calibration method are verified by evaluating the image reconstruction quality. In conclusion, the proposed method can effectively reconstruct accurate AFM images of the grating.


  • Fast AFM Imaging Based on Compressive Sensing Using Undersampled Raster Scan

    by Yixiang Niu, Guoqiang Han

    Atomic force microscope (AFM), which has nanoscale precision, is a widely used instrument in material science and biomedical science. Nevertheless, conventional AFM scanning is a time-consuming procedure. Compressive sensing (CS) and undersampling techniques have been introduced to accomplish fast AFM imaging in recent years. At present, existing undersampled scan patterns cannot simultaneously guarantee imaging efficiency and quality well. Therefore, a novel one called undersampled raster (USR) scan is put forward in this article. It has higher imaging efficiency than most existing scan patterns, which is drawn by calculating the scanning time with the proposed estimation formulas. Experimental results show that the imaging quality is obviously better than using other combinations of fast scan patterns and reconstruction algorithms when the regular form of the USR scan is employed with Total Variation Minimization by Augmented Lagrangian and Alternating Direction Algorithm (TVAL3). The universality of this imaging scheme is verified by using a variety of samples. In the end, the applications of regular USR scan or its variant for super-resolution AFM imaging and predicting appropriate sampling rates are proposed. In conclusion, applying regular USR scan and TVAL3 algorithm to CS-based AFM can effectively realize fast and high-quality imaging.


  • Coral-flake Co particles electrodeposited into the porous NiAl matrix

    by Jianjun Gao, Jian Luo, Haibin Geng, Jianhua Zhong, Guoqiang Han, Kai Cui, Zhilong Zhao, Lin Liu