Krzysztof Wincza
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Krzysztof Wincza has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Slawomir Gruszczynski
Institute of Electronics, AGH University of Krakow, Krakw, Poland
42 shared publications - Ilona Piekarz
Institute of Electronics, AGH University of Krakow, Krakw, Poland
14 shared publications - Jakub Sorocki
AGH University of Krakow
13 shared publications - Kamil Staszek
Institute of Electronics, AGH University of Krakow, Krakw, Poland
13 shared publications - Robert Smolarz
AGH University of Krakow, Kraków, Poland
13 shared publications - Andrzej Dudek
AGH University of Krakow
6 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (9) , 8235-8245
Compact OTA-Like Measurement System Based on Mikaelian GRIN Lens Antennas for Complex Permittivity Evaluation
- 1 September 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 74 (9) , 8235-8245
Open AccessCompact OTA-Like Measurement System Based on Mikaelian GRIN Lens Antennas for Complex Permittivity Evaluation
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 131265-131276
A Fully Planar Feeding Network for Excitation of Series-Fed Dual-Polarized Antenna Arrays With Even Number of Radiating Elements
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 131265-131276
Open AccessA Fully Planar Feeding Network for Excitation of Series-Fed Dual-Polarized Antenna Arrays With Even Number of Radiating Elements
- Open Access
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- p. 1-12
Ultrawideband Multiprobe Reflectometer Designated for MMIC Technology
- 1 January 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- p. 1-12
Open AccessUltrawideband Multiprobe Reflectometer Designated for MMIC Technology
- Open Access
- 5 August 2025
- Published by MDPI AG in Electronics
- Vol. 14 (15) , 3123
Novel Synthesis Method for Microwave Parallel-Coupled Resonator Bandpass Filters
In this study, a novel synthesis method for bandpass filters is proposed. The method relies on Richard’s transform and avoids approximations in circuit realizations. Thus, proper frequency responses are obtained for bandpass filters with bandwidths ranging from narrow to wide. In the presented approach, a method for removing the input and output inverters/transformers is proposed and is used to show how classic parallel-coupled resonator filters can be designed using the proposed method. Also, a degree of freedom is introduced that allows the overall impedance level of the fabricated filter to be tuned, which is used to tune the frequency response of the filter to the theoretical one. Both narrow-band and wideband solutions in terms of impedance inverter realization are discussed in the paper. The theoretical investigations are confirmed by an experimental realization of two bandpass filters with parallel-coupled shorted resonators.
- 5 August 2025
- Published by MDPI AG in Electronics
- Vol. 14 (15) , 3123
Open AccessNovel Synthesis Method for Microwave Parallel-Coupled Resonator Bandpass Filters
In this study, a novel synthesis method for bandpass filters is proposed. The method relies on Richard’s transform and avoids approximations in circuit realizations. Thus, proper frequency responses are obtained for bandpass filters with bandwidths ranging from narrow to wide. In the presented approach, a method for removing the input and output inverters/transformers is proposed and is used to show how classic parallel-coupled resonator filters can be designed using the proposed method. Also, a degree of freedom is introduced that allows the overall impedance level of the fabricated filter to be tuned, which is used to tune the frequency response of the filter to the theoretical one. Both narrow-band and wideband solutions in terms of impedance inverter realization are discussed in the paper. The theoretical investigations are confirmed by an experimental realization of two bandpass filters with parallel-coupled shorted resonators.
- Open Access
- 26 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 111567-111576
Low-Cost and Highly Sensitive Reflective-Mode Phase-Variation Sensor for Bacteria Detection
This paper presents a reflective-mode planar microwave biosensor based on phase-variation allowing for the detection of low bacteria concentration. The sensor is a one-port coplanar waveguide (CPW) structure implemented by means of a pair of weakly coupled step-impedance resonators (SIRs). The high sensitivity needed for bacteria detection is obtained by modulating (reducing) the coupling level between the pair of resonators, which simply requires separating such resonators enough. A sensor demonstrator is developed to operate in K-band, resulting in a compact structure manufactured using a single-layer metal-on-glass technology. An experimental study is conducted on an example of detection of various concentrations of E. coli bacteria, where the phase variation at single frequency is an indicator of the bacteria presence. The measurement results show that as low as 100 colony-forming-unit in 1 ml (100 CFU/ml) of bacteria suspension can be easily detected with sensitivity of 3.24° per order of concentration, indicating potential to go even lower with detection threshold, which is superior to many state-of-the-art E. coli microwave biosensors.
- 26 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 111567-111576
Open AccessLow-Cost and Highly Sensitive Reflective-Mode Phase-Variation Sensor for Bacteria Detection
This paper presents a reflective-mode planar microwave biosensor based on phase-variation allowing for the detection of low bacteria concentration. The sensor is a one-port coplanar waveguide (CPW) structure implemented by means of a pair of weakly coupled step-impedance resonators (SIRs). The high sensitivity needed for bacteria detection is obtained by modulating (reducing) the coupling level between the pair of resonators, which simply requires separating such resonators enough. A sensor demonstrator is developed to operate in K-band, resulting in a compact structure manufactured using a single-layer metal-on-glass technology. An experimental study is conducted on an example of detection of various concentrations of E. coli bacteria, where the phase variation at single frequency is an indicator of the bacteria presence. The measurement results show that as low as 100 colony-forming-unit in 1 ml (100 CFU/ml) of bacteria suspension can be easily detected with sensitivity of 3.24° per order of concentration, indicating potential to go even lower with detection threshold, which is superior to many state-of-the-art E. coli microwave biosensors.
- Open Access
- 22 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (8) , 2692-2696
Compact Modified Mikaelian GRIN Lens Antenna With Gain and Bandwidth Improvement
This letter proposes a compact Mikaelian lens antenna (LA). The proposed antenna consists of an aperture-coupled patch (ACP) antenna with a patch printed directly on a graded refractive index (GRIN) lens. By loading the ACP antenna with the dielectric lens, the antenna impedance bandwidth increases from 17.5% to 33%. In addition, the lens refractive index (RI) profile is angularly modified with the use of $cos(2\phi)$ function to improve the radiation pattern and gain of the LA to achieve the maximum theoretical aperture efficiency (AE) of 116% at 24 GHz. The proposed concept was validated in simulations and measurements of the LA operating in the 23–34.5 GHz frequency range. The fabricated LA has a volume of $2\lambda \times 2\lambda \times 1.76\lambda$ at 24 GHz. It achieves a maximum AE of 58% at 23.5 GHz for gain of 13.7 dBi, which could be improved to 96% with the use of low-loss materials.
- 22 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 24 (8) , 2692-2696
Open AccessCompact Modified Mikaelian GRIN Lens Antenna With Gain and Bandwidth Improvement
This letter proposes a compact Mikaelian lens antenna (LA). The proposed antenna consists of an aperture-coupled patch (ACP) antenna with a patch printed directly on a graded refractive index (GRIN) lens. By loading the ACP antenna with the dielectric lens, the antenna impedance bandwidth increases from 17.5% to 33%. In addition, the lens refractive index (RI) profile is angularly modified with the use of $cos(2\phi)$ function to improve the radiation pattern and gain of the LA to achieve the maximum theoretical aperture efficiency (AE) of 116% at 24 GHz. The proposed concept was validated in simulations and measurements of the LA operating in the 23–34.5 GHz frequency range. The fabricated LA has a volume of $2\lambda \times 2\lambda \times 1.76\lambda$ at 24 GHz. It achieves a maximum AE of 58% at 23.5 GHz for gain of 13.7 dBi, which could be improved to 96% with the use of low-loss materials.
- Open Access
- 20 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (12) , 4683-4687
Series-Fed Dual-Polarized Antenna Arrays for Single-Layer Photolithography Fabrication
This letter proposes a novel method to design series-fed (SF) dual-polarized antenna arrays. The proposed antenna arrays consist of $nm$ radiating elements placed in $n \times m$ grids, where $n$ and $m$ are arbitrary odd numbers. The proposed arrays are fed by two probes, each of which is used to excite one of the TM 10 and TM 01 modes in the middle patch, and hence, one of two orthogonal linear polarizations. For each polarization, the middle patch operates also as a four-way power divider to distribute the signals that excite this polarization across the array. Both the radiating elements and the feeding network of the antenna array are realized on a single metal layer, which makes the proposed antenna array a low-cost solution. The proposed antenna concept has been verified by the design and measurements of a $3 \times 3$ antenna array. The prototype operates over 5.53–5.87 GHz frequency range and achieves a maximum gain of 15.8 dBi at 5.84 GHz.
- 20 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Antennas and Wireless Propagation Letters
- Vol. 23 (12) , 4683-4687
Open AccessSeries-Fed Dual-Polarized Antenna Arrays for Single-Layer Photolithography Fabrication
This letter proposes a novel method to design series-fed (SF) dual-polarized antenna arrays. The proposed antenna arrays consist of $nm$ radiating elements placed in $n \times m$ grids, where $n$ and $m$ are arbitrary odd numbers. The proposed arrays are fed by two probes, each of which is used to excite one of the TM 10 and TM 01 modes in the middle patch, and hence, one of two orthogonal linear polarizations. For each polarization, the middle patch operates also as a four-way power divider to distribute the signals that excite this polarization across the array. Both the radiating elements and the feeding network of the antenna array are realized on a single metal layer, which makes the proposed antenna array a low-cost solution. The proposed antenna concept has been verified by the design and measurements of a $3 \times 3$ antenna array. The prototype operates over 5.53–5.87 GHz frequency range and achieves a maximum gain of 15.8 dBi at 5.84 GHz.
- Open Access
- 8 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 93841-93847
Impedance-Transforming Transdirectional Coupled-Line Directional Couplers With Maximum Achievable Transformation Ratio
A novel concept of impedance-transforming transdirectional coupled-line directional couplers that feature maximum available impedance transformation ratio is proposed. It is shown that such couplers can be designed as an appropriate connection of two uncoupled two-wire transmission lines, having electrical lengths equal 90° and 270°. The conditions for ideal impedance match and isolation in such couplers are derived and formulas describing the required characteristic impedances of the two two-wire transmission lines are given. It is shown that in such circuits the input and isolated port can be terminated with different impedances than the coupled and through ports. The major advantage of the proposed circuits is their reciprocity which allows for application in multiport amplifiers. The concept has been verified by the design and measurement of a 3-dB transdirectional coupler operating at a center frequency of 1 GHz that allows for achieving impedance transformation ratio $R =2$ proving the correctness of the presented analysis.
- 8 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 93841-93847
Open AccessImpedance-Transforming Transdirectional Coupled-Line Directional Couplers With Maximum Achievable Transformation Ratio
A novel concept of impedance-transforming transdirectional coupled-line directional couplers that feature maximum available impedance transformation ratio is proposed. It is shown that such couplers can be designed as an appropriate connection of two uncoupled two-wire transmission lines, having electrical lengths equal 90° and 270°. The conditions for ideal impedance match and isolation in such couplers are derived and formulas describing the required characteristic impedances of the two two-wire transmission lines are given. It is shown that in such circuits the input and isolated port can be terminated with different impedances than the coupled and through ports. The major advantage of the proposed circuits is their reciprocity which allows for application in multiport amplifiers. The concept has been verified by the design and measurement of a 3-dB transdirectional coupler operating at a center frequency of 1 GHz that allows for achieving impedance transformation ratio $R =2$ proving the correctness of the presented analysis.
- Open Access
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 83260-83268
Broadband Impedance Inverters for Application in Synthesis and Realization of Bandpass Filters
A novel circuit of impedance inverter has been proposed, which allows for efficient design of bandpass microwave filters. The synthesis approach relies on direct application of Richard’s transform to a lumped element prototype. Further impedance inverters are applied, which are composed of transmission-line sections with quarterwave-long shorted sections having negative impedance. The proposed impedance inverters are well suited for filters having from narrow to broad bandwidths. The proposed design method has been applied in the design of exemplary 5th and 9th order badndpass filters with directly connected transmission-line sections. The obtained measurement results support the proposed design method showing a good agreement with the theoretical results.
- 11 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 83260-83268
Open AccessBroadband Impedance Inverters for Application in Synthesis and Realization of Bandpass Filters
A novel circuit of impedance inverter has been proposed, which allows for efficient design of bandpass microwave filters. The synthesis approach relies on direct application of Richard’s transform to a lumped element prototype. Further impedance inverters are applied, which are composed of transmission-line sections with quarterwave-long shorted sections having negative impedance. The proposed impedance inverters are well suited for filters having from narrow to broad bandwidths. The proposed design method has been applied in the design of exemplary 5th and 9th order badndpass filters with directly connected transmission-line sections. The obtained measurement results support the proposed design method showing a good agreement with the theoretical results.
- Open Access
- 16 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 129425-129435
Broadband Monolithic GaN Balanced Amplifier Composed of Mixed Cascade-Tandem Directional Couplers and Cascode Stages
In this paper we present a broadband monolithic balanced amplifier reaching 30 dBm output power over a range from 5.7 GHz up to 35.1 GHz. To the best of our knowledge, such broad operational bandwidth has never been reported in literature for balanced topology. The amplifier is composed of broadband tandem-cascade directional couplers and amplifying blocks designed in cascode topology. It is worth noticing that for the first time the mixed tandem-cascade couplers have been integrated in monolithic process, in which only one metallization layer is available for transmission-line structures. The broadband balanced amplifier has been fabricated in high power GH15 gallium nitride (GaN) process offered by United Monolithic Semiconductors (UMS). The measured saturation output power and 1-dB compression point are equal to 30 dBm and 27.8 dBm, respectively.
- 16 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 129425-129435
Open AccessBroadband Monolithic GaN Balanced Amplifier Composed of Mixed Cascade-Tandem Directional Couplers and Cascode Stages
In this paper we present a broadband monolithic balanced amplifier reaching 30 dBm output power over a range from 5.7 GHz up to 35.1 GHz. To the best of our knowledge, such broad operational bandwidth has never been reported in literature for balanced topology. The amplifier is composed of broadband tandem-cascade directional couplers and amplifying blocks designed in cascode topology. It is worth noticing that for the first time the mixed tandem-cascade couplers have been integrated in monolithic process, in which only one metallization layer is available for transmission-line structures. The broadband balanced amplifier has been fabricated in high power GH15 gallium nitride (GaN) process offered by United Monolithic Semiconductors (UMS). The measured saturation output power and 1-dB compression point are equal to 30 dBm and 27.8 dBm, respectively.