Natalia Yu Babaeva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Natalia Yu Babaeva has a total of 52 co-authors. Here are the top co-authors by number of shared publications:
- George V. Naidis
Joint Institute for High Temperatures, Russian Academy of Sciences , Moscow 125412
37 shared publications - Dmitry V. Tereshonok
Joint Institute for High Temperatures, Russian Academy of Sciences, Moscow, Russia
13 shared publications Mark J. Kushner
University of Michigan, Ann Arbor, MI , USA
7 shared publications- Tao Shao
State Key Laboratory of Power Grid Environmental Protection School of Electrical Engineering and Automation Wuhan University Wuhan China
7 shared publications - Victor F. Tarasenko
Institute of High Current Electronics of the Siberian Branch of the Russian Academy of Sciences
7 shared publications - Cheng Zhang
Beijing International S&T Cooperation Base for Plasma Science and Energy Conversion, Institute of Electrical Engineering, Chinese Academy of Sciences
4 shared publications
Latest Publications
- Open Access
- 5 February 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (5)
Interaction of atmospheric pressure helium plasma jets with hollow dielectric targets: Shallow and deep grooves
The results of a computational study of helium plasma jet interaction with hollow dielectric grooves of various sizes are presented. It is shown that the character of interaction of ionization waves formed in plasma jets with treated objects depends substantially on the value of the dielectric permittivity of the groove material. For grooves with low permittivities, ionization waves penetrate inside and touch the bottom of the groove. For grooves with high permittivities, the reflected waves are formed after the contact of primary ionization wave with the groove edges, thus hindering penetration of plasma inside the groove interior.
- 5 February 2026
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 139 (5)
Open AccessInteraction of atmospheric pressure helium plasma jets with hollow dielectric targets: Shallow and deep grooves
The results of a computational study of helium plasma jet interaction with hollow dielectric grooves of various sizes are presented. It is shown that the character of interaction of ionization waves formed in plasma jets with treated objects depends substantially on the value of the dielectric permittivity of the groove material. For grooves with low permittivities, ionization waves penetrate inside and touch the bottom of the groove. For grooves with high permittivities, the reflected waves are formed after the contact of primary ionization wave with the groove edges, thus hindering penetration of plasma inside the groove interior.
- Open Access
- 1 December 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (21)
Effects produced in dielectric barrier discharges by dielectric structures not in contact with plasma: 2D modeling approach
The paper presents results of a computational study of the effects of different catalytic structures on the plasma parameters in dielectric barrier discharge (DBD) reactors. The catalytic structures, rods and voids with spherical and ellipsoidal cross sections having different orientations, are embedded into the bottom dielectric of a DBD reactor and are not in contact with plasmas. These structures enhance or deplete the electric field due to their polarization by approaching DBD surface streamers. The electric field enhancement in such structured DBDs depends upon the geometrical layout and the dielectric constant of the structures. The mode of plasma propagation is also sensitive to the shape and orientation of the rods and voids. It is found that the embedded material with higher dielectric constant produces more intense enhancement or depletion of plasma density in vicinity of rods or voids, respectively. It is shown that, in the considered arrangement, the rods mainly serve as catalysts while voids act as inhibitors for plasma processing. The electric field enhancement results in increasing fluxes of reactive species toward the surface where the catalytic structure is located. It is shown that by producing the designed combinations of rods and voids, one can control the production of useful species in the gas phase and, as a result, the production of fluxes of useful species to surfaces.
- 1 December 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 138 (21)
Open AccessEffects produced in dielectric barrier discharges by dielectric structures not in contact with plasma: 2D modeling approach
The paper presents results of a computational study of the effects of different catalytic structures on the plasma parameters in dielectric barrier discharge (DBD) reactors. The catalytic structures, rods and voids with spherical and ellipsoidal cross sections having different orientations, are embedded into the bottom dielectric of a DBD reactor and are not in contact with plasmas. These structures enhance or deplete the electric field due to their polarization by approaching DBD surface streamers. The electric field enhancement in such structured DBDs depends upon the geometrical layout and the dielectric constant of the structures. The mode of plasma propagation is also sensitive to the shape and orientation of the rods and voids. It is found that the embedded material with higher dielectric constant produces more intense enhancement or depletion of plasma density in vicinity of rods or voids, respectively. It is shown that, in the considered arrangement, the rods mainly serve as catalysts while voids act as inhibitors for plasma processing. The electric field enhancement results in increasing fluxes of reactive species toward the surface where the catalytic structure is located. It is shown that by producing the designed combinations of rods and voids, one can control the production of useful species in the gas phase and, as a result, the production of fluxes of useful species to surfaces.
- Open Access
- 1 October 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (10)
Positive streamers in air: Effect of the average applied field
An approximate approach to estimating the average velocity and radius of streamers generated at the fronts of applied voltage pulses is presented. It is shown that this approach gives the dependence of the average streamer parameters on the value of the average applied electric field consistent with results of numerical streamer simulations.
- 1 October 2025
- Published by AIP Publishing in Physics of Plasmas
- Vol. 32 (10)
Open AccessPositive streamers in air: Effect of the average applied field
An approximate approach to estimating the average velocity and radius of streamers generated at the fronts of applied voltage pulses is presented. It is shown that this approach gives the dependence of the average streamer parameters on the value of the average applied electric field consistent with results of numerical streamer simulations.
- 20 September 2024
- Published by Wiley in Plasma Processes and Polymers
- Vol. 21 (12)
On the Energy Cost for Nitrogen Fixation in DC Glow Discharges in Atmospheric‐Pressure Air
Modeling of the production of nitrogen oxide molecules in DC discharges in laminar longitudinal flows of atmospheric‐pressure air is performed. Two‐dimensional nonequilibrium discharge model includes the system of gas dynamic equations and balance equations for various plasma components. Simulations are performed for the discharge currents 50–600 mA and gas flow velocities 1–10 m/s. In considered conditions, the gas temperature in the discharge core varies in the range of 3000–6000 K. Spatial profiles of the densities and fluxes of produced species are obtained, both inside the discharge and in the afterglow region. The energy cost for the production of nitrogen oxides is calculated, depending on the discharge current, gap length, and gas flow velocity. The results of the simulation are compared with available experimental data.
- 20 September 2024
- Published by Wiley in Plasma Processes and Polymers
- Vol. 21 (12)
On the Energy Cost for Nitrogen Fixation in DC Glow Discharges in Atmospheric‐Pressure Air
Modeling of the production of nitrogen oxide molecules in DC discharges in laminar longitudinal flows of atmospheric‐pressure air is performed. Two‐dimensional nonequilibrium discharge model includes the system of gas dynamic equations and balance equations for various plasma components. Simulations are performed for the discharge currents 50–600 mA and gas flow velocities 1–10 m/s. In considered conditions, the gas temperature in the discharge core varies in the range of 3000–6000 K. Spatial profiles of the densities and fluxes of produced species are obtained, both inside the discharge and in the afterglow region. The energy cost for the production of nitrogen oxides is calculated, depending on the discharge current, gap length, and gas flow velocity. The results of the simulation are compared with available experimental data.
- 1 May 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (5) , 055013
Simulation of low-current DC discharges in longitudinal flows of atmospheric-pressure air
Characteristics of low-current stationary axially symmetric discharges in longitudinal laminar flows of atmospheric-pressure air calculated in the framework of a two-dimensional model are presented. Non-equilibrium discharge regimes, in the current range from 1 to 100 mA, are considered for gas flow velocities up to 50 m s−1. It is shown that variation of the flow velocity substantially affects the discharge characteristics, such as the width of discharge column, the electric field inside the gap, the current density etc. Validity of the obtained results is confirmed by their comparison with available experimental data.
- 1 May 2024
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 33 (5) , 055013
Simulation of low-current DC discharges in longitudinal flows of atmospheric-pressure air
Characteristics of low-current stationary axially symmetric discharges in longitudinal laminar flows of atmospheric-pressure air calculated in the framework of a two-dimensional model are presented. Non-equilibrium discharge regimes, in the current range from 1 to 100 mA, are considered for gas flow velocities up to 50 m s−1. It is shown that variation of the flow velocity substantially affects the discharge characteristics, such as the width of discharge column, the electric field inside the gap, the current density etc. Validity of the obtained results is confirmed by their comparison with available experimental data.
- Open Access
- 1 December 2023
- Published by AIP Publishing in Physics of Plasmas
- Vol. 30 (12)
Backward fast electrons supported by ionization wave passing through the grid cathode
In this paper, the effect of appearance of fast electrons behind the grid cathode in the direction reverse to the anode is studied computationally. Fast electrons are observed within 0.5 ns after application of a short voltage pulse. The results obtained confirm the possibility of generation of backward fast electrons (some of them are in a runaway mode) and explain the main trends of this process. It is shown that backward fast electrons are supported by the ionization wave (IW). The IW evolution proceeds via two phases. During the first phase, first fast electrons are observed moving toward the anode. Then, multiple individual IWs starting from each individual cathode wire are formed in the anode–cathode gap. The duration of this stage is 0.3 ns and corresponds to the pulse rise time. At the second phase, the separate individual IWs merge in a single flat ionization wave. The IW penetrates through the cathode wires and propagates in the direction reverse to the anode. The preferred direction of fast electrons propagation also reverses. Now, the trajectories of fast electrons are mainly directed away from the anode. The duration of the recorded flux of fast electrons is of the order of a few picoseconds. This time interval correlates with the available experimental data.
- 1 December 2023
- Published by AIP Publishing in Physics of Plasmas
- Vol. 30 (12)
Open AccessBackward fast electrons supported by ionization wave passing through the grid cathode
In this paper, the effect of appearance of fast electrons behind the grid cathode in the direction reverse to the anode is studied computationally. Fast electrons are observed within 0.5 ns after application of a short voltage pulse. The results obtained confirm the possibility of generation of backward fast electrons (some of them are in a runaway mode) and explain the main trends of this process. It is shown that backward fast electrons are supported by the ionization wave (IW). The IW evolution proceeds via two phases. During the first phase, first fast electrons are observed moving toward the anode. Then, multiple individual IWs starting from each individual cathode wire are formed in the anode–cathode gap. The duration of this stage is 0.3 ns and corresponds to the pulse rise time. At the second phase, the separate individual IWs merge in a single flat ionization wave. The IW penetrates through the cathode wires and propagates in the direction reverse to the anode. The preferred direction of fast electrons propagation also reverses. Now, the trajectories of fast electrons are mainly directed away from the anode. The duration of the recorded flux of fast electrons is of the order of a few picoseconds. This time interval correlates with the available experimental data.
- 1 August 2023
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 32 (8) , 085019
On CO2 conversion in discharges in CO2–N2 mixtures
Recent results on the efficiency of CO2 conversion in discharges in CO2–N2 mixtures are discussed. Conditions are considered when the dominating conversion mechanism is dissociation of CO2 molecules in collisions with nitrogen molecules in several electronically excited states. Its efficiency is determined by the values of dissociation yields in these collisions. Knowledge of dissociation yields for various N2 excited states is rather poor. In this paper, the effects of variation of these yields on the conversion efficiency are evaluated. Comparison of the obtained estimates with available experimental data allows ascertaining the yield values.
- 1 August 2023
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 32 (8) , 085019
On CO2 conversion in discharges in CO2–N2 mixtures
Recent results on the efficiency of CO2 conversion in discharges in CO2–N2 mixtures are discussed. Conditions are considered when the dominating conversion mechanism is dissociation of CO2 molecules in collisions with nitrogen molecules in several electronically excited states. Its efficiency is determined by the values of dissociation yields in these collisions. Knowledge of dissociation yields for various N2 excited states is rather poor. In this paper, the effects of variation of these yields on the conversion efficiency are evaluated. Comparison of the obtained estimates with available experimental data allows ascertaining the yield values.
- 15 July 2023
- Published by Springer Nature
- p. 583-604
Atmospheric Pressure Plasma Jets and Their Interaction with Dielectric Surfaces
- 15 July 2023
- Published by Springer Nature
- p. 583-604
Atmospheric Pressure Plasma Jets and Their Interaction with Dielectric Surfaces
- 1 May 2023
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 32 (5) , 054001
CO2 conversion in a microwave plasma torch: 2D vs 1D approaches
In the present study, we computationally investigate the splitting of CO2 to carbon monoxide and oxygen in an atmospheric pressure microwave (MW) plasma torch. We demonstrate different stages of CO2 conversion while using 2D and 1D models. For both models, we use identical sets of chemical reactions, cross sections, power profiles and dimensions of the plasma region. Based on the real MW plasma torch device, we first constructed two-dimensional geometry and obtained results using the 2D model. Then, the 1D plug-flow model was employed. With 1D model we expected to obtain the results close to those we already had from the 2D approach. However, we revealed that the gas temperature and plasma species behaviour in 1D model was quite different from those obtained with the 2D code. We revisited the 2D results and found that the reverse (upstream) gas flow near the central electrode was responsible for the observed discrepancies. In 2D model, the residence time of a certain portion of gas was much longer. When the flow rate in 1D model was adjusted, the reasonable agreement between both models was achieved.
- 1 May 2023
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 32 (5) , 054001
CO2 conversion in a microwave plasma torch: 2D vs 1D approaches
In the present study, we computationally investigate the splitting of CO2 to carbon monoxide and oxygen in an atmospheric pressure microwave (MW) plasma torch. We demonstrate different stages of CO2 conversion while using 2D and 1D models. For both models, we use identical sets of chemical reactions, cross sections, power profiles and dimensions of the plasma region. Based on the real MW plasma torch device, we first constructed two-dimensional geometry and obtained results using the 2D model. Then, the 1D plug-flow model was employed. With 1D model we expected to obtain the results close to those we already had from the 2D approach. However, we revealed that the gas temperature and plasma species behaviour in 1D model was quite different from those obtained with the 2D code. We revisited the 2D results and found that the reverse (upstream) gas flow near the central electrode was responsible for the observed discrepancies. In 2D model, the residence time of a certain portion of gas was much longer. When the flow rate in 1D model was adjusted, the reasonable agreement between both models was achieved.
- 18 January 2023
- Published by IOP Publishing in Plasma Science and Technology
- Vol. 25 (3) , 035406
Evolution of ionization waves in a multi-pulsed plasma jet: the role of memory charges
In this paper, we discuss the properties of ionization waves (IWs) in a multi-pulsed plasma jet while using the two-dimensional computational approach. The IWs are generated by application of three short negative pulses with a repetition frequency 12.5 MHz. The simulations are performed continuously during a single run while accounting for charges accumulated inside (surface charges) and outside (space charges) the tube. The plasma forming gas mixture (He/O2 = 99.8%/0.2%) is injected through the discharge tube into the surrounding humid air. We show that an IW can emerge from the tube exit at a pulse rising edge (as a negative IW) and at a falling edge of the same pulse (as a positive IW). It is demonstrated that remnants of the negative and positive charges play an essential role in the discharge evolution. The first pulse travels the shortest distance as it propagates through the initially non-ionized environment. The IWs developing during the second pulse essentially enlarge the plasma plume length. At the same time, the IWs generated by the third pulse eventually decay due to the remnants of charges accumulated during the previous pulses. Accumulated memory charges can lead to the IW extinction.
- 18 January 2023
- Published by IOP Publishing in Plasma Science and Technology
- Vol. 25 (3) , 035406
Evolution of ionization waves in a multi-pulsed plasma jet: the role of memory charges
In this paper, we discuss the properties of ionization waves (IWs) in a multi-pulsed plasma jet while using the two-dimensional computational approach. The IWs are generated by application of three short negative pulses with a repetition frequency 12.5 MHz. The simulations are performed continuously during a single run while accounting for charges accumulated inside (surface charges) and outside (space charges) the tube. The plasma forming gas mixture (He/O2 = 99.8%/0.2%) is injected through the discharge tube into the surrounding humid air. We show that an IW can emerge from the tube exit at a pulse rising edge (as a negative IW) and at a falling edge of the same pulse (as a positive IW). It is demonstrated that remnants of the negative and positive charges play an essential role in the discharge evolution. The first pulse travels the shortest distance as it propagates through the initially non-ionized environment. The IWs developing during the second pulse essentially enlarge the plasma plume length. At the same time, the IWs generated by the third pulse eventually decay due to the remnants of charges accumulated during the previous pulses. Accumulated memory charges can lead to the IW extinction.