Yugang Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yugang Zhou has a total of 216 co-authors. Here are the top co-authors by number of shared publications:
Youdou Zheng
Jiangsu Key Laboratory of Advanced Semi-conductors and High Energy Efficiency Devices, School of Electronic Science and Engineering, Nanjing University 1 , Nanjing 210023
25 shared publications- Kei May Lau
The Hong Kong University of Science and Technology
16 shared publications Rong Zhang
Jiangsu Provincial Key Laboratory of Advanced Photonic and Electronic Materials, School of Electronic Science and Engineering, Nanjing University, Nanjing, People’s Republic of China
16 shared publications- Rong Zhang
Nanjing University
14 shared publications - Kevin Jing Chen
The Hong Kong University of Science and Technology
13 shared publications - Bin Liu
Nanjing University
12 shared publications
Latest Publications
- 9 November 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (19)
Revealing luminescence mechanisms in red InGaN micro-LEDs via spatially resolved, temperature- and current-dependent electroluminescence
In order to elucidate the luminescence mechanisms in red InGaN micro-LEDs, we measured and analyzed spatially resolved and temperature- and current-dependent electroluminescence spectra. Under low current density, a high-energy emission peak other than the red one was observed in regions containing V-pit defects, while the red emission intensity in these V-pit regions is relatively stronger. The above-mentioned phenomenon can be explained by high-energy emission from the quantum wells at the sidewall of V-pits and the carrier leakage channels through the V-pit defects. These channels facilitate electron–hole recombination along the z axis direction. Further temperature- and current-dependent measurements revealed an anomalous temperature-dependent behavior: under an injection current of 1 mA, when the temperature drops below 160 K, the optical power decreases with further cooling. This is mainly ascribed to the transfer of carriers between different localized states, which modifies their distribution and recombination within the xy-plane of the quantum wells. Collectively, our models provide a comprehensive explanation of the carrier dynamics and spatial kinetics of red InGaN LEDs in different emission regions and under varying temperature and current conditions, offering important insights into the emission mechanisms and valuable guidance for the optimization of epitaxial structure design.
- 9 November 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (19)
Revealing luminescence mechanisms in red InGaN micro-LEDs via spatially resolved, temperature- and current-dependent electroluminescence
In order to elucidate the luminescence mechanisms in red InGaN micro-LEDs, we measured and analyzed spatially resolved and temperature- and current-dependent electroluminescence spectra. Under low current density, a high-energy emission peak other than the red one was observed in regions containing V-pit defects, while the red emission intensity in these V-pit regions is relatively stronger. The above-mentioned phenomenon can be explained by high-energy emission from the quantum wells at the sidewall of V-pits and the carrier leakage channels through the V-pit defects. These channels facilitate electron–hole recombination along the z axis direction. Further temperature- and current-dependent measurements revealed an anomalous temperature-dependent behavior: under an injection current of 1 mA, when the temperature drops below 160 K, the optical power decreases with further cooling. This is mainly ascribed to the transfer of carriers between different localized states, which modifies their distribution and recombination within the xy-plane of the quantum wells. Collectively, our models provide a comprehensive explanation of the carrier dynamics and spatial kinetics of red InGaN LEDs in different emission regions and under varying temperature and current conditions, offering important insights into the emission mechanisms and valuable guidance for the optimization of epitaxial structure design.
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (10) , 2079-2082
Monolithic Integration of Mg-Free Trench-Gate MOSFETs and μ LEDs
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (10) , 2079-2082
Monolithic Integration of Mg-Free Trench-Gate MOSFETs and μ LEDs
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (7) , 4465-4469
Design and Realization of GaN-Based Trench-Gate MOSFETs Based on Graded Al-Composition AlGaN Channel Layer
- 1 July 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (7) , 4465-4469
Design and Realization of GaN-Based Trench-Gate MOSFETs Based on Graded Al-Composition AlGaN Channel Layer
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (6) , 3903-3907
High-Efficiency Deep Ultraviolet Light-Emitting Diode Based on Ag-Nanodot/Pd/Al Composite Electrode
The light extraction efficiency (LEE) of AlGaN-based deep-ultraviolet light-emitting diodes (DUV LEDs) is severely constrained by the strong ultraviolet (UV) absorption of the p-GaN contact layer and the low reflectivity of the p-type electrode to UV light. In this work, Ag-nanodot (AgND)/Pd/Al composite electrodes with varying coverage ratios were fabricated via an Ag–Pd displacement reaction on the 8-nm-thick p-GaN surface to enhance the overall reflectivity of the electrode. The feasibility of the Ag–Pd displacement reaction was confirmed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analyses. Three-dimensional finite-difference time-domain (3D-FDTD) simulations and reflectivity measurements on sapphire substrates consistently demonstrate that reducing the coverage ratio of AgND/Pd effectively improves electrode reflectivity. At a driving current of 40 mA, the light output power (LOP) and wall-plug efficiency (WPE) of DUV LEDs fabricated with AgNDs/Pd/Al electrodes (coverage ratio: 18.9%) are increased by 89% and 65.8%, respectively, compared with those using fully covered Ag/Pd/Al electrodes. The results of this study highlight the key role of p-electrode reflectivity in achieving high-efficiency DUV LEDs and provide a feasible technical route for improving the LEE of DUV LEDs.
- 27 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (6) , 3903-3907
High-Efficiency Deep Ultraviolet Light-Emitting Diode Based on Ag-Nanodot/Pd/Al Composite Electrode
The light extraction efficiency (LEE) of AlGaN-based deep-ultraviolet light-emitting diodes (DUV LEDs) is severely constrained by the strong ultraviolet (UV) absorption of the p-GaN contact layer and the low reflectivity of the p-type electrode to UV light. In this work, Ag-nanodot (AgND)/Pd/Al composite electrodes with varying coverage ratios were fabricated via an Ag–Pd displacement reaction on the 8-nm-thick p-GaN surface to enhance the overall reflectivity of the electrode. The feasibility of the Ag–Pd displacement reaction was confirmed by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) analyses. Three-dimensional finite-difference time-domain (3D-FDTD) simulations and reflectivity measurements on sapphire substrates consistently demonstrate that reducing the coverage ratio of AgND/Pd effectively improves electrode reflectivity. At a driving current of 40 mA, the light output power (LOP) and wall-plug efficiency (WPE) of DUV LEDs fabricated with AgNDs/Pd/Al electrodes (coverage ratio: 18.9%) are increased by 89% and 65.8%, respectively, compared with those using fully covered Ag/Pd/Al electrodes. The results of this study highlight the key role of p-electrode reflectivity in achieving high-efficiency DUV LEDs and provide a feasible technical route for improving the LEE of DUV LEDs.
- 20 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (6) , 1157-1160
3-D Stacked Full-Color μ LED Displays With Monolithic-Integrated Bismuth Ferrite-Based Color Filter
To overcome the key bottlenecks in realizing high-performance full-color micro light-emitting diodes ($\mu $ LEDs) displays, we introduce a three-dimensional (3D) stacking technology that is compatible with both heterogeneous integration and monolithic integration. Although$\mu $ LED display technologies are promising for next-generation AR/VR devices, their development is hampered by low integration yield, limited pixel density, and inadequate color performance. Our approach enables the fabrication of a high-performance${16}\times {16}$ full-color$\mu $ LED display chip featuring a wide color gamut (110% NTSC) and high pixel density (328 pixels per inch (PPI)). It is the first to integrate a bismuth ferrite (BiFeO3, BFO)-based color filter in the full-color chip, resulting in exceptional red color purity. The 3D architecture streamlines the integration of the color conversion layer, color filter, and driver circuit, offering superior design flexibility. This work provides a viable and efficient path toward the industrial-scale manufacturing of advanced$\mu $ LED displays for emerging visual applications.- 20 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (6) , 1157-1160
3-D Stacked Full-Color μ LED Displays With Monolithic-Integrated Bismuth Ferrite-Based Color Filter
To overcome the key bottlenecks in realizing high-performance full-color micro light-emitting diodes ($\mu $ LEDs) displays, we introduce a three-dimensional (3D) stacking technology that is compatible with both heterogeneous integration and monolithic integration. Although$\mu $ LED display technologies are promising for next-generation AR/VR devices, their development is hampered by low integration yield, limited pixel density, and inadequate color performance. Our approach enables the fabrication of a high-performance${16}\times {16}$ full-color$\mu $ LED display chip featuring a wide color gamut (110% NTSC) and high pixel density (328 pixels per inch (PPI)). It is the first to integrate a bismuth ferrite (BiFeO3, BFO)-based color filter in the full-color chip, resulting in exceptional red color purity. The 3D architecture streamlines the integration of the color conversion layer, color filter, and driver circuit, offering superior design flexibility. This work provides a viable and efficient path toward the industrial-scale manufacturing of advanced$\mu $ LED displays for emerging visual applications.- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (4) , 804-807
In Situ Junction Temperature Measurement and Thermal Resistance Extraction of AlGaN/GaN HEMTs Using Schottky Diode-Integrated Sensor
This letter presents a new method for real-time in-situ temperature measurement and thermal resistance extraction of AlGaN/GaN high electron mobility transistors (HEMTs) based on Schottky diode integrated sensors for the first time. Through an innovative structure design, the independent Schottky diode sensor is integrated near the gate of the HEMT, and the fabrication process is fully compatible with the standard electrode manufacturing process. Experimental results show that the sensor has a temperature sensitivity of 4.192 mV/°C. (testing current $= 1.0~\mu $ A) and a time resolution of microsecond is achieved, which can realize transient temperature monitoring without affecting the operation state of the device. It shows high temperature sensitivity without measurement delay time caused by circuit switching. Meanwhile, it does not require the damage to package which is necessary in the optical methods. It can accurately capture the transient temperature change of the hot spot near the gate and construct the structure function, so as to extract the thermal resistance of each layer of the package device. The integrated sensor provides an effective characterization method for the thermal management optimization of power devices, and shows an important application value in the field of reliability analysis and heat dissipation design. This method can also serve as a benchmark for evaluating alternative temperature-measurement techniques.
- 4 March 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 47 (4) , 804-807
In Situ Junction Temperature Measurement and Thermal Resistance Extraction of AlGaN/GaN HEMTs Using Schottky Diode-Integrated Sensor
This letter presents a new method for real-time in-situ temperature measurement and thermal resistance extraction of AlGaN/GaN high electron mobility transistors (HEMTs) based on Schottky diode integrated sensors for the first time. Through an innovative structure design, the independent Schottky diode sensor is integrated near the gate of the HEMT, and the fabrication process is fully compatible with the standard electrode manufacturing process. Experimental results show that the sensor has a temperature sensitivity of 4.192 mV/°C. (testing current $= 1.0~\mu $ A) and a time resolution of microsecond is achieved, which can realize transient temperature monitoring without affecting the operation state of the device. It shows high temperature sensitivity without measurement delay time caused by circuit switching. Meanwhile, it does not require the damage to package which is necessary in the optical methods. It can accurately capture the transient temperature change of the hot spot near the gate and construct the structure function, so as to extract the thermal resistance of each layer of the package device. The integrated sensor provides an effective characterization method for the thermal management optimization of power devices, and shows an important application value in the field of reliability analysis and heat dissipation design. This method can also serve as a benchmark for evaluating alternative temperature-measurement techniques.
- 27 August 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (35) , 355104
Electric field modulation and hot-electron suppression in AlGaN/GaN HEMTs on Si using a hybrid p-NiO RESURF-FP termination
We report enhanced breakdown voltage (V BR) and reliability in AlGaN/GaN HEMTs on silicon substrates by employing a hybrid termination structure consisting of a p-type NiO reduced surface field (RESURF) layer and an extended NiO field plate (FP). The RESURF-FP hybrid structure modulates the lateral electric field via a dual mechanism: (1) charge-assisted depletion engineering by the p-NiO RESURF layer and (2) capacitive coupling effect by the gate-connected NiO FP, without introducing additional mobile charge carriers. Electrostatic simulations show that this dual-modulation strategy effectively suppresses lateral electric field peaks, shifts the peak field away from the gate edge, and reduces its field strength from 4 MV cm−1 to 3.1 MV cm−1, thereby suppressing hot-carrier injection and interface degradation. As a result, the devices exhibit a 45% improvement in V BR while maintaining a high on-state current and a low specific on-resistance (R on,sp) of 3 mΩ cm2. Reliability characterization under gate pulse and high-temperature conditions show minimal threshold voltage shift (<0.1 V), confirming suppressed interface traps and improved device stability enabled by the etching-free regrown p-NiO gate and field-modulated termination design. These results demonstrate an effective strategy for electric field control and reliability enhancement in high-voltage GaN-on-Si HEMTs.
- 27 August 2025
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (35) , 355104
Electric field modulation and hot-electron suppression in AlGaN/GaN HEMTs on Si using a hybrid p-NiO RESURF-FP termination
We report enhanced breakdown voltage (V BR) and reliability in AlGaN/GaN HEMTs on silicon substrates by employing a hybrid termination structure consisting of a p-type NiO reduced surface field (RESURF) layer and an extended NiO field plate (FP). The RESURF-FP hybrid structure modulates the lateral electric field via a dual mechanism: (1) charge-assisted depletion engineering by the p-NiO RESURF layer and (2) capacitive coupling effect by the gate-connected NiO FP, without introducing additional mobile charge carriers. Electrostatic simulations show that this dual-modulation strategy effectively suppresses lateral electric field peaks, shifts the peak field away from the gate edge, and reduces its field strength from 4 MV cm−1 to 3.1 MV cm−1, thereby suppressing hot-carrier injection and interface degradation. As a result, the devices exhibit a 45% improvement in V BR while maintaining a high on-state current and a low specific on-resistance (R on,sp) of 3 mΩ cm2. Reliability characterization under gate pulse and high-temperature conditions show minimal threshold voltage shift (<0.1 V), confirming suppressed interface traps and improved device stability enabled by the etching-free regrown p-NiO gate and field-modulated termination design. These results demonstrate an effective strategy for electric field control and reliability enhancement in high-voltage GaN-on-Si HEMTs.
- 11 August 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (6)
Enhanced performance of normally-off AlGaN/GaN MOS-HEMTs taking advantage of extreme-k BaTiO3 with prominent dielectric polarization
In the letter, we demonstrate that the performance enhancement of normally-off AlGaN/GaN metal–oxide–semiconductor-high-electron-mobility transistors (MOS-HEMTs) benefits from the prominent dielectric polarization of extreme-k BaTiO3. The fabricated HEMTs exhibit a high threshold voltage of 1.67 V, attributed to the additional negative polarization bound charges at the BaTiO3/AlGaN interface and the resulting expansion of depletion width under negative gate bias. A relatively large saturation output current of 374 mA/mm is also achieved thanks to the additional positive polarization bound charges and the resulting enhancement of channel electron concentration under positive gate bias. Further, the extremely high dielectric constant of BaTiO3 and the corresponding capacitive coupling effect enable a notable improvement in channel controllability, achieving a high maximum transconductance of 108.7 mS/mm and a small subthreshold swing of 69.6 mV/dec. The proposed BaTiO3-MOS-HEMTs with fine post-etch treatments also exhibit low gate leakage, a competitive breakdown field of 1.4 MV/cm, and a high Baliga's figure-of-merit of 1.05 GW/cm2. These findings elucidate the substantial potential of extreme-k BaTiO3 for high-performance normally-off AlGaN/GaN power switching applications.
- 11 August 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (6)
Enhanced performance of normally-off AlGaN/GaN MOS-HEMTs taking advantage of extreme-k BaTiO3 with prominent dielectric polarization
In the letter, we demonstrate that the performance enhancement of normally-off AlGaN/GaN metal–oxide–semiconductor-high-electron-mobility transistors (MOS-HEMTs) benefits from the prominent dielectric polarization of extreme-k BaTiO3. The fabricated HEMTs exhibit a high threshold voltage of 1.67 V, attributed to the additional negative polarization bound charges at the BaTiO3/AlGaN interface and the resulting expansion of depletion width under negative gate bias. A relatively large saturation output current of 374 mA/mm is also achieved thanks to the additional positive polarization bound charges and the resulting enhancement of channel electron concentration under positive gate bias. Further, the extremely high dielectric constant of BaTiO3 and the corresponding capacitive coupling effect enable a notable improvement in channel controllability, achieving a high maximum transconductance of 108.7 mS/mm and a small subthreshold swing of 69.6 mV/dec. The proposed BaTiO3-MOS-HEMTs with fine post-etch treatments also exhibit low gate leakage, a competitive breakdown field of 1.4 MV/cm, and a high Baliga's figure-of-merit of 1.05 GW/cm2. These findings elucidate the substantial potential of extreme-k BaTiO3 for high-performance normally-off AlGaN/GaN power switching applications.
- 21 July 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (3)
Impedance-dependent degradation in GaN HEMTs under high-voltage RF stress: Electro-thermal and trap mechanisms
This work investigated impedance-dependent degradation mechanisms in GaN high-electron-mobility transistors (HEMTs) under high-voltage radio frequency (RF) stress, focusing on electro-thermal coupling and trap evolution. In devices with matched impedance, slight degradation in output power (Pout), saturated drain current (Idss), and transconductance (GM) is observed after RF stress. This is attributed to an increase in trap density within the AlGaN layer and at the AlGaN/GaN interface, as evidenced by low-frequency noise results. In contrast, severe degradation in Pout, Idss, GM, and gate leakage current (IG) occurs in those devices with the 50-Ω mismatched impedance condition. Anyway, these more severe degradation effects result not only from the increased trap density after RF stress, but also primarily from the temperature rise caused by reflected power-induced Joule heating, as validated by infrared thermography. Electro-thermal simulations reveal dual lateral electric field peaks near gate edges in 50-Ω mismatched devices, redistributing peak temperature toward the source–gate region and intensifying localized Joule heating, thereby accelerating degradation. These findings highlight the critical role of impedance matching in GaN HEMT reliability, offering guidelines for designing robust power amplifiers in microwave systems.
- 21 July 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (3)
Impedance-dependent degradation in GaN HEMTs under high-voltage RF stress: Electro-thermal and trap mechanisms
This work investigated impedance-dependent degradation mechanisms in GaN high-electron-mobility transistors (HEMTs) under high-voltage radio frequency (RF) stress, focusing on electro-thermal coupling and trap evolution. In devices with matched impedance, slight degradation in output power (Pout), saturated drain current (Idss), and transconductance (GM) is observed after RF stress. This is attributed to an increase in trap density within the AlGaN layer and at the AlGaN/GaN interface, as evidenced by low-frequency noise results. In contrast, severe degradation in Pout, Idss, GM, and gate leakage current (IG) occurs in those devices with the 50-Ω mismatched impedance condition. Anyway, these more severe degradation effects result not only from the increased trap density after RF stress, but also primarily from the temperature rise caused by reflected power-induced Joule heating, as validated by infrared thermography. Electro-thermal simulations reveal dual lateral electric field peaks near gate edges in 50-Ω mismatched devices, redistributing peak temperature toward the source–gate region and intensifying localized Joule heating, thereby accelerating degradation. These findings highlight the critical role of impedance matching in GaN HEMT reliability, offering guidelines for designing robust power amplifiers in microwave systems.