Muslem Uddin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Muslem Uddin has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Galina Mirzaeva
School of Engineering, The University of Newcastle, Callaghan, NSW, Australia
13 shared publications - Marco Rivera
University of Nottingham
9 shared publications - Saad Mekhilef
Swinburne University of Technology
9 shared publications - Graham Clifford Goodwin
The University of Newcastle
7 shared publications - Jose Rodriguez
Universidad San Sebastián Santiago
5 shared publications Peter Stepien
School of Electrical Engineering and Computing, University of Newcastle,Callaghan,NSW,Australia,2308
4 shared publications
Latest Publications
- Open Access
Decentralised Consensus Control of Hybrid Synchronous Condenser and Grid-Forming Inverter Systems in Renewable-Dominated Low-Inertia Grids
The increasing penetration of renewable energy sources (RESs) has significantly altered the operational characteristics of modern power systems, resulting in reduced system inertia and fault current capacity. These developments introduce new challenges for maintaining frequency and voltage stability, particularly in low-inertia grids that are dominated by inverter-based resources (IBRs). This paper presents a hierarchical control framework that integrates synchronous condensers (SCs) and grid-forming (GFM) inverters through a leader–follower consensus control architecture to address these issues. In this approach, selected GFMs act as leaders to restore nominal voltage and frequency, while follower GFMs and SCs collaboratively share active and reactive power. The primary control employs droop-based regulation, and a distributed secondary layer enables proportional power sharing via peer-to-peer communication. A modified IEEE 14-bus test system is implemented in PSCAD to validate the proposed strategy under scenarios including load disturbances, reactive demand variations, and plug-and-play operations. Compared to conventional droop-based control, the proposed framework reduces frequency nadir by up to 0.3 Hz and voltage deviation by 1.1%, achieving optimised sharing indices. Results demonstrate that consensus-based coordination enhances dynamic stability and power-sharing fairness and supports the flexible integration of heterogeneous assets without requiring centralised control.
Open AccessDecentralised Consensus Control of Hybrid Synchronous Condenser and Grid-Forming Inverter Systems in Renewable-Dominated Low-Inertia Grids
The increasing penetration of renewable energy sources (RESs) has significantly altered the operational characteristics of modern power systems, resulting in reduced system inertia and fault current capacity. These developments introduce new challenges for maintaining frequency and voltage stability, particularly in low-inertia grids that are dominated by inverter-based resources (IBRs). This paper presents a hierarchical control framework that integrates synchronous condensers (SCs) and grid-forming (GFM) inverters through a leader–follower consensus control architecture to address these issues. In this approach, selected GFMs act as leaders to restore nominal voltage and frequency, while follower GFMs and SCs collaboratively share active and reactive power. The primary control employs droop-based regulation, and a distributed secondary layer enables proportional power sharing via peer-to-peer communication. A modified IEEE 14-bus test system is implemented in PSCAD to validate the proposed strategy under scenarios including load disturbances, reactive demand variations, and plug-and-play operations. Compared to conventional droop-based control, the proposed framework reduces frequency nadir by up to 0.3 Hz and voltage deviation by 1.1%, achieving optimised sharing indices. Results demonstrate that consensus-based coordination enhances dynamic stability and power-sharing fairness and supports the flexible integration of heterogeneous assets without requiring centralised control.
- 24 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 33 (6) , 2243-2254
A Robust Decoupled Predictive Control With Resonance Suppression and CMV Elimination for a Four-Leg Inverter Fed Induction Motor Drives
This article proposes a predictive control scheme for a four-leg inverter fed induction motor (IM) drive with a motor-side LC filter. The third-order (LCL) filter/load structure poses control challenges. These challenges are addressed in the proposed scheme by separating the traditional finite set model predictive control (FS-MPC) into two independent stages: controller and modulator. To avoid the trade-offs typically associated with FS-MPC, the two stages are then separately designed to achieve different objectives. The controller stage provides optimal control with integral action at the fundamental frequency, resulting in excellent tracking performance and low sensitivity to modeling errors and disturbances. The modulator stage features a feedback quantizer (FBQ) with a feedback notch filter. This provides low harmonic distortion of the load current, suppresses resonances, and eliminates common mode voltage (CMV). The proposed ac drive solution is validated by simulation and experiment.
- 24 June 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Control Systems Technology
- Vol. 33 (6) , 2243-2254
A Robust Decoupled Predictive Control With Resonance Suppression and CMV Elimination for a Four-Leg Inverter Fed Induction Motor Drives
This article proposes a predictive control scheme for a four-leg inverter fed induction motor (IM) drive with a motor-side LC filter. The third-order (LCL) filter/load structure poses control challenges. These challenges are addressed in the proposed scheme by separating the traditional finite set model predictive control (FS-MPC) into two independent stages: controller and modulator. To avoid the trade-offs typically associated with FS-MPC, the two stages are then separately designed to achieve different objectives. The controller stage provides optimal control with integral action at the fundamental frequency, resulting in excellent tracking performance and low sensitivity to modeling errors and disturbances. The modulator stage features a feedback quantizer (FBQ) with a feedback notch filter. This provides low harmonic distortion of the load current, suppresses resonances, and eliminates common mode voltage (CMV). The proposed ac drive solution is validated by simulation and experiment.
- Open Access
- 11 June 2025
- Published by Elsevier in Electric Power Systems Research
- Vol. 248
Generation expansion planning: Transitioning toward decarbonization with a focus on reliability and Dunkelflaute
- 11 June 2025
- Published by Elsevier in Electric Power Systems Research
- Vol. 248
Open AccessGeneration expansion planning: Transitioning toward decarbonization with a focus on reliability and Dunkelflaute
- Open Access
AC-DC Power Systems Optimization with Droop Control Smooth Approximation
This paper addresses the challenges of embedding common droop control characteristics in ac-dc power system steady-state simulation and optimization problems. We propose a smooth approximation methodology to construct differentiable functions that encode the attributes of piecewise linear droop control with saturation. We transform the nonsmooth droop curves into smooth nonlinear equality constraints, solvable with Newton methods and interior point solvers. These constraints are then added to power flow, optimal power flow, and security-constrained optimal power flow problems in ac-dc power systems. The results demonstrate significant improvements in accuracy in terms of power sharing response, voltage regulation, and system efficiency, while outperforming existing mixed-integer formulations in computational efficiency.
Open AccessAC-DC Power Systems Optimization with Droop Control Smooth Approximation
This paper addresses the challenges of embedding common droop control characteristics in ac-dc power system steady-state simulation and optimization problems. We propose a smooth approximation methodology to construct differentiable functions that encode the attributes of piecewise linear droop control with saturation. We transform the nonsmooth droop curves into smooth nonlinear equality constraints, solvable with Newton methods and interior point solvers. These constraints are then added to power flow, optimal power flow, and security-constrained optimal power flow problems in ac-dc power systems. The results demonstrate significant improvements in accuracy in terms of power sharing response, voltage regulation, and system efficiency, while outperforming existing mixed-integer formulations in computational efficiency.
- Open Access
- 25 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Industry Applications
- Vol. 3, 114-124
Robust Model Predictive Control for AFE-Inverter Drives With Common Mode Voltage Elimination
This paper proposes a novel and robust version of Model Predictive Control scheme for AC drives based on Voltage Source Inverter (VSI) with Active Front End (AFE). The main feature of the proposed MPC is elimination of Common Mode Voltage (CMV) without imposing a penalty on the corresponding term in the cost function, but rather by a smart utilisation of the restricted set of switching states in a computationally efficient algorithm. Furthermore, the paper proposes to split the conventional MPC scheme into separate Control and Modulation stages, and to enhance the Control stage by integral action, and the Modulation stage - by a Feedback Quantizer. The resulting AC drive scheme provides high tracking accuracy over the full speed range, robustness to disturbances and parameters error, coupled with practically zero CMV and consequently - very low levels of conducted and radiated electromagnetic interference (EMI). This makes the proposed scheme a competitive alternative to the existing AC drive solutions in the most challenging industrial applications. The benefits of the proposed scheme are validated by simulation and experiment.
- 25 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Open Journal of Industry Applications
- Vol. 3, 114-124
Open AccessRobust Model Predictive Control for AFE-Inverter Drives With Common Mode Voltage Elimination
This paper proposes a novel and robust version of Model Predictive Control scheme for AC drives based on Voltage Source Inverter (VSI) with Active Front End (AFE). The main feature of the proposed MPC is elimination of Common Mode Voltage (CMV) without imposing a penalty on the corresponding term in the cost function, but rather by a smart utilisation of the restricted set of switching states in a computationally efficient algorithm. Furthermore, the paper proposes to split the conventional MPC scheme into separate Control and Modulation stages, and to enhance the Control stage by integral action, and the Modulation stage - by a Feedback Quantizer. The resulting AC drive scheme provides high tracking accuracy over the full speed range, robustness to disturbances and parameters error, coupled with practically zero CMV and consequently - very low levels of conducted and radiated electromagnetic interference (EMI). This makes the proposed scheme a competitive alternative to the existing AC drive solutions in the most challenging industrial applications. The benefits of the proposed scheme are validated by simulation and experiment.
- 1 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 56 (4) , 4365-4374
Common Mode Voltage Elimination in Variable Speed Drives for Improved Electrical Safety
Common-mode-voltage (CMV) is a well-known source of bearing currents and electromagnetic interference (EMI) in industrial applications. In underground mining environment, where impedance-earthed IT earthing system is typical, CMV is additionally associated with potentially undetectable fault currents, due to their diversion away from a protection circuit. This paper proposes a VSD solution that generates practically zero CMV and removes alternative paths for the fault currents. The VSD topology utilized in this paper is a standard 2-level Inverter with Active Front End. The paper develops a control strategy such that it eliminates CMV, minimizes EMI and optimizes harmonic distortion at the drive input and output. Experiments conducted in a representative laboratory environment, have confirmed the practical elimination of CMV and EMI, and effectiveness of the earth fault protection.
- 1 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 56 (4) , 4365-4374
Common Mode Voltage Elimination in Variable Speed Drives for Improved Electrical Safety
Common-mode-voltage (CMV) is a well-known source of bearing currents and electromagnetic interference (EMI) in industrial applications. In underground mining environment, where impedance-earthed IT earthing system is typical, CMV is additionally associated with potentially undetectable fault currents, due to their diversion away from a protection circuit. This paper proposes a VSD solution that generates practically zero CMV and removes alternative paths for the fault currents. The VSD topology utilized in this paper is a standard 2-level Inverter with Active Front End. The paper develops a control strategy such that it eliminates CMV, minimizes EMI and optimizes harmonic distortion at the drive input and output. Experiments conducted in a representative laboratory environment, have confirmed the practical elimination of CMV and EMI, and effectiveness of the earth fault protection.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Feedback Quantizer based Model Predictive Control for Inverters with Active Front End
This paper attempts to overcome the known drawbacks of Finite Set Model Predictive Control (FS-MPC) and proposes an MPC-based AC drive with competitive performance to the existing industrial drives. The paper complements the traditional MPC approach with elements of classical control and feedback quantization (FBQ) principles. The proposed FBQ- MPC operates in dq-rotating frame, includes integral action and an advanced modulator. Subsequently, it offers improved tracking performance, low sensitivity to modeling errors and disturbances, low harmonics and low EMI, making it an attractive solution for various applications. Findings of the paper are validated by extensive simulations and experimental results.
- 1 November 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Feedback Quantizer based Model Predictive Control for Inverters with Active Front End
This paper attempts to overcome the known drawbacks of Finite Set Model Predictive Control (FS-MPC) and proposes an MPC-based AC drive with competitive performance to the existing industrial drives. The paper complements the traditional MPC approach with elements of classical control and feedback quantization (FBQ) principles. The proposed FBQ- MPC operates in dq-rotating frame, includes integral action and an advanced modulator. Subsequently, it offers improved tracking performance, low sensitivity to modeling errors and disturbances, low harmonics and low EMI, making it an attractive solution for various applications. Findings of the paper are validated by extensive simulations and experimental results.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Electrically safe variable speed drive for underground mining applications
Common-mode-voltage (CMV) is a well-known source of bearing currents and electromagnetic interference (EMI) in industrial applications. In underground earthing and protection environment, CMV is associated with potentially undetectable fault currents, due to their diversion away from the protection circuit. An ideal solution to these problems would be such a VSD that creates minimum or zero CMV and removes the alternative paths for the fault currents. Previous study performed by the authors has suggested that, amongst the existing drive topologies used by the industry, a 2-level Inverter with Active Front End (AFE) would be ideally suited for CMV elimination. This paper develops a control strategy for the VSD based on AFE Inverter such that it eliminates CMV, minimises EMI and optimizes harmonic distortion at the drive input and output sides. To validate the proposed strategy, a laboratory prototype VSD has been developed and the test environment has been set up to represent an underground mining electrical system. Experiments have confirmed that the prototype VSD generates practically no CMV, thus eliminating the EMI problem. Under an earth fault, the fault current flows into the designated protection circuit, thus providing the required electrical safety of the proposed VSD.
- 1 September 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-8
Electrically safe variable speed drive for underground mining applications
Common-mode-voltage (CMV) is a well-known source of bearing currents and electromagnetic interference (EMI) in industrial applications. In underground earthing and protection environment, CMV is associated with potentially undetectable fault currents, due to their diversion away from the protection circuit. An ideal solution to these problems would be such a VSD that creates minimum or zero CMV and removes the alternative paths for the fault currents. Previous study performed by the authors has suggested that, amongst the existing drive topologies used by the industry, a 2-level Inverter with Active Front End (AFE) would be ideally suited for CMV elimination. This paper develops a control strategy for the VSD based on AFE Inverter such that it eliminates CMV, minimises EMI and optimizes harmonic distortion at the drive input and output sides. To validate the proposed strategy, a laboratory prototype VSD has been developed and the test environment has been set up to represent an underground mining electrical system. Experiments have confirmed that the prototype VSD generates practically no CMV, thus eliminating the EMI problem. Under an earth fault, the fault current flows into the designated protection circuit, thus providing the required electrical safety of the proposed VSD.
- 1 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Model Predictive Control of Direct Matrix Converter with Common Mode Voltage Elimination
Common-mode-voltage (CMV) is known for creating electromagnetic interference and bearing currents in industrial drive applications. This problem is exacerbated in mobile applications, due to the use of long cables carrying supply and protective earth conductors. In such applications matrix converters are seen as a potential drive solution. This paper presents a detailed study showing the possibility to completely eliminate CMV in the matrix converter based system, using voltage control based model predictive control (MPC). The paper compares performance of the direct matrix converter (DMC) for different output frequencies, under the imposed condition of zero CMV. The paper also presents a systematical discretization method, which is used to accurately calculate the input filter constants. Based on extensive simulations performed in MATLAB-Simulink environment, the paper demonstrates suitability of DMC based drives for CMV-sensitive applications.
- 1 December 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-7
Model Predictive Control of Direct Matrix Converter with Common Mode Voltage Elimination
Common-mode-voltage (CMV) is known for creating electromagnetic interference and bearing currents in industrial drive applications. This problem is exacerbated in mobile applications, due to the use of long cables carrying supply and protective earth conductors. In such applications matrix converters are seen as a potential drive solution. This paper presents a detailed study showing the possibility to completely eliminate CMV in the matrix converter based system, using voltage control based model predictive control (MPC). The paper compares performance of the direct matrix converter (DMC) for different output frequencies, under the imposed condition of zero CMV. The paper also presents a systematical discretization method, which is used to accurately calculate the input filter constants. Based on extensive simulations performed in MATLAB-Simulink environment, the paper demonstrates suitability of DMC based drives for CMV-sensitive applications.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 6418-6423
Computationally Efficient Model Predictive Control for AC-DC-AC Converter with Common Mode Voltage Elimination
This paper proposes a computationally efficient modified model predictive control (MMPC) method for AFE-rectifier based AC-DC-AC converter system, to eliminate the common-mode-voltage (CMV) without any degradation of harmonic profile of the load current, as well as to significantly reduce the computational time of the predictive algorithm. The proposed MMPC method is formulated in voltage domain rather than current domain as in traditional MPC method. In the proposed MMPC method, sector pre-determination is adopted, to reduce the available finite-control-set (FCS), which significantly reduces the computational time for the predictive algorithm. Also, CMV is eliminated by applying synchronization between the rectifier and inverter parts of AFE-rectifier based AC-DC-AC converter, when selecting the optimal switching combination for the next sampling interval. The proposed MMPC method is verified in MATLAB-Simulink. The results confirm that the proposed method achieve the following outcomes: significantly reduces the computational time, completely eliminates the CMV without degradation of harmonic content, and opens the door to improve the power quality in any CMV sensitive industry applications by utilizing faster sampling frequency.
- 1 September 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 6418-6423
Computationally Efficient Model Predictive Control for AC-DC-AC Converter with Common Mode Voltage Elimination
This paper proposes a computationally efficient modified model predictive control (MMPC) method for AFE-rectifier based AC-DC-AC converter system, to eliminate the common-mode-voltage (CMV) without any degradation of harmonic profile of the load current, as well as to significantly reduce the computational time of the predictive algorithm. The proposed MMPC method is formulated in voltage domain rather than current domain as in traditional MPC method. In the proposed MMPC method, sector pre-determination is adopted, to reduce the available finite-control-set (FCS), which significantly reduces the computational time for the predictive algorithm. Also, CMV is eliminated by applying synchronization between the rectifier and inverter parts of AFE-rectifier based AC-DC-AC converter, when selecting the optimal switching combination for the next sampling interval. The proposed MMPC method is verified in MATLAB-Simulink. The results confirm that the proposed method achieve the following outcomes: significantly reduces the computational time, completely eliminates the CMV without degradation of harmonic content, and opens the door to improve the power quality in any CMV sensitive industry applications by utilizing faster sampling frequency.