FCFang Chen

Fang Chen

*This is an algorithmically generated author record based on publicly available information.

Fang Chen has a total of 32 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • A Power Control Strategy for Electric Vehicles Charging Based on AC/DC Hybrid Distribution Network

    by Haojing Wang, Jin Li, Qin Xu, Shanshan Shi, Zhixian Wang, Chen Fang

    As the popularity of electric vehicles increases, their diverse charging methods present various challenges to the power grid. This paper introduces a hybrid AC-DC distribution grid and its charging power control method, which simultaneously accommodates AC slow-charging and DC fast-charging for electric vehicles. The proposed hybrid AC-DC distribution grid utilizes a topology structure where the secondary winding of the transformer is independently connected to an H-bridge grid-connected inverter in three phases. This configuration allows for the connection of single-phase AC slow-charging to the AC 220V bus and DC fast-charging to the DC 375V bus. Based on this topology, a charging power control strategy is proposed, employing a grid-connected inverter control structure with a voltage outer loop and a current inner loop. The voltage outer loop utilizes a PI controller to stabilize the DC voltage, while the current inner loop incorporates an additional compensation instruction for the unbalanced current extracted from the three-phase load current on the AC side. The current reference is precisely tracked without error using a PR regulator in the current loop. The proposed hybrid AC-DC distribution network and its power control strategy can meet the requirements of DC fast-charging while compensating for the three-phase unbalanced current caused by single-phase AC slow-charging. Finally, the proposed topology and control strategy are validated through simulation models and case studies.

  • Research and realization of gigabit Ethernet frame slicing

    by Fang Chen, Bozhong Li, Zifan Li, Yang Li, Yuanlong Peng, Yingxu Wang, Ying Guo, Jianjun Wu

    Aiming at solving the problem that RS code cannot be applied in gigabit Ethernet transmission due to the length of Ethernet random frame, a module for slicing Ethernet frame is designed in this paper. The designed slicing module can slice Ethernet frames of any length to adapt to RS codes of different lengths, and the receiver module can find the slicing frame header again and restore the slicing frame to Ethernet frame. The experimental results show that the designed transmitter and receiver can slice and restore Ethernet frames at Gigabit rate, and there are no transmission error frames, which meets the design requirements.

  • Research on Efficiency Improvement Strategy of A New Type of Photovoltaic Power Generation Conversion System

    by Ruien Bian, Chaozhi Deng, Fang Chen

    With the increasingly prominent environmental problems, the proportion of photovoltaic in distributed power supply is increasing. In this paper, a new tracking method of solar maximum power point is proposed, which can keep the system in the position of maximum power point, and build on Matlab/Simulink simulation model to proposed method is verified.

  • Investigation of Nonlinear Droop Control in DC Power Distribution Systems: Load Sharing, Voltage Regulation, Efficiency, and Stability

    by Fang Chen, Rolando Burgos, Dushan Boroyevich, Juan C. Vasquez, Josep M. Guerrero

    Linear droop faces the design tradeoff between voltage regulation and load sharing due to cable resistances and sensing errors. Using a larger droop resistance improves load sharing, but requires a wider droop voltage range. In the nonlinear droop, droop resistance is a function of the converter's output current, and its value increases when the output current increases. As a result, the impacts from sensors and cables are reduced. In this paper, the design of nonlinear droop in dc power distribution systems is studied with special emphasis on load sharing, voltage regulation, system efficiency, and stability. After discussing the piecewise linear and nonlinear droop control, a generic polynomial expression is presented to unify different droop equations. The impact of droop on dc system efficiency is analyzed by evaluating cable and power converter losses. The converter's output impedance using nonlinear droop is modeled to analyze the system stability with constant power loads. The selection and design guidelines of nonlinear droop are summarized, considering both the static performance and interaction with load systems. The analysis is verified in 400-V multi-source dc systems. The nonlinear droop is fully distributed as it only needs local information.


  • Weighted Double Sampling to Obtain the Average Value of Triangular Current for Accurate Droop Control in DC Power Distribution Systems

    by Fang Chen

    Droop control is broadly used in dc power distribution systems, e.g., dc microgrids. Implementing droop control for switch mode power supplies requires the measurement of average current. Synchronous sampling is used in digital control systems to obtain the average of a triangular inductor waveform. However, the dead time, semiconductor turn-on and turn-off delays, and signal conditioning delays shift the sensed waveform and change the effective duty cycle, resulting in a misalignment and measurement error from the average value. This paper proposes a duty cycle weighted averaging method based on double sampling. By sampling twice per switching period and averaging the results using duty cycle as the weighting factor, the error due to waveform misalignment is theoretically eliminated. The result always equals the average value of the triangle. This method does not rely on the knowledge of circuit delays, making it easy to implement and robust to parameter variations. Simulations and experimental measurements validate the superior performance compared with conventional single and double sampling methods. The experiment on a droop-controlled dc-dc converter demonstrates a more accurate droop characteristic.


  • Load Shedding Scheme with Deep Reinforcement Learning to Improve Short-term Voltage Stability

    by Jingyi Zhang, Chao Lu, Chen Fang, Xiang Ling, Yong Zhang

    In this paper, a novel load shedding scheme against voltage instability with deep reinforcement learning (DRL). The convolutional neural networks (CNNs) are chosen to automatically learn the features and exploit the local spatial correlations from TS data of voltages. The DRL load shedding controller interacts with system dynamics through a sequence of observations, actions and rewards with two convolutional neural networks, namely critic and actor networks. The critic network is used to evaluate the quality of the load shedding actions and the actor network to determine the time, location and amounts of load shedding (LS). A global reward function is defined considering the recovery characteristics of voltages and total load shedding amounts to guarantee the coordination of under voltage load shedding (UVLS). The simulation is performed on the modified New England 39-bus system, and the results validate the voltage recovery performance and load shedding amount of the proposed scheme under different scenario.


  • A Bidirectional High-Efficiency Transformerless Converter With Common-Mode Decoupling for the Interconnection of AC and DC Grids

    by Fang Chen, Rolando Burgos, Dushan Boroyevich

    This paper presents an interface ac-dc converter to connect the 380 V bipolar dc microgrid with the 240 V split-phase single-phase ac utility. The design targets are high efficiency, small volume and symmetric bipolar dc bus generation. A transformerless two-stage topology is proposed to decouple the low-frequency common-mode (CM) voltage between the connected ac and dc systems. The two-stage structure also reduces the required capacitance in single-phase power conversion by allowing voltage ripple on the intermediate dc-link. Adaptive dc-link voltage control and interleaving of state-of-the-art silicon carbide (SiC) MOSFETs are adopted to achieve high efficiency. Interleaving angles are optimized for a small volume of both differential-mode and CM magnetics. An active CM control method is incorporated to regulate the dc and low-frequency CM voltages on the dc buses. The resultant dc bus voltages are rendered symmetric to the ground, and the leakage current is suppressed. The generated - 190 V dc bus is suitable for bipolar 380 V dc power distribution systems. Pluggable phase-leg modules with embedded driving and protection circuit are designed and tested, based on which a 10 kW converter prototype is built achieving an efficiency > 97 %.


  • Beat Frequency Oscillation Analysis for Power Electronic Converters in DC Nanogrid Based on Crossed Frequency Output Impedance Matrix Model

    by Xiaolong Yue, Dushan Boroyevich, Fred C. Lee, Fang Chen, Rolando Burgos, Fang Zhuo

    The interaction of power electronic converters in a microgrid can introduce system instability and power quality issues. Existing investigations focus on interactions either in low-frequency regions, such as the constant power load, or in very high-frequency regions like electromagnetic interference. However, interactions of power converters around their switching frequency range are not included. In fact, the interaction of dc-dc converters with different switching frequencies can introduce beat frequency oscillation in certain cases. Since additional frequency component (beat frequency) is generated, traditional impedance concept is no longer the tool for beat frequency oscillation analysis and new models need to be developed. In this paper, a crossed frequency output impedance matrix model is proposed to describe the terminal characteristics of a dc-dc converter around its switching frequency range. A high-frequency equivalent circuit model for the converter is then developed to predict the beat frequency oscillation in parallel and cascaded systems, which results from the interaction of power converters with different switching frequencies. Finally, design guidelines are proposed to avoid potential beat frequency oscillation in a dc nanogrid. Experimental results for both parallel and cascaded systems validate the accuracy and effectiveness of the proposed prediction method and design guidelines.


  • Economic Dispatch for Operating Cost Minimization Under Real-Time Pricing in Droop-Controlled DC Microgrid

    by Chendan Li, Federico de Bosio, Fang Chen, Sanjay K. Chaudhary, Juan C. Vasquez, Josep M. Guerrero

    In this paper, an economic dispatch problem for total operation cost minimization in dc microgrids is formulated. An operating cost is associated with each generator in the microgrid, including the utility grid, combining the cost-efficiency of the system with demand response requirements of the utility. The power flow model is included in the optimization problem, thus the transmission losses can be considered for generation dispatch. By considering the primary (local) control of the grid-forming converters of a microgrid, optimal parameters can be directly applied to this control level, thus achieving higher control accuracy and faster response. The optimization problem is solved in a heuristic method. In order to test the proposed algorithm, a six-bus droop-controlled dc microgrid is used in the case studies. Simulation results show that under variable renewable energy generation, load consumption, and electricity prices, the proposed method can successfully reduce the operating cost by dispatching economically the resources in the microgrid.


  • Analysis and distributed control of power flow in DC microgrids to improve system efficiency

    by Fang Chen, Rolando Burgos, Dushan Boroyevich, Enrique Rodriguez-Diaz, Lexuan Meng, Juan C. Vasquez, Josep M. Guerrero

    DC Microgrid attains popularity in integrating renewable energy sources and batteries. It also has the potential to achieve higher efficiency than ac power grid with optimized power flow. In this paper, a general dc microgrid is modeled based on a cluster of general dc nodes, which includes constant power renewables generation, droop-controlled voltage source and different kinds of load. Then the dc power flow is solved for optimization. A voltage restoration method based on consensus algorithm is used to restore the voltage deviation from droop characteristic. An enhanced current regulator is adopted to guarantee the accurate load sharing even under the influence of sensor drift and line resistance. A tie line power flow control method is proposed to regulate the tie line power directly and increase the system efficiency at light load condition. All the considered methods only need the local information and the information from its nearest neighbor thus the system expendability is guaranteed. Simulation and experiment results are provided to validate the proposed methods.