Johanne Mouzon
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Johanne Mouzon has a total of 102 co-authors. Here are the top co-authors by number of shared publications:
- Magnus Odén
Linköping University
11 shared publications Jonas Hedlund
8 shared publications- Farid Akhtar
Division of Materials Science, Luleå University of Technology, Luleå 97187, Sweden
4 shared publications J. Hedlund
4 shared publications- Danil Korelskiy
Chemical Technology, Luleå University of Technology, SE-971 87 Luleå, Sweden
3 shared publications I.U. Bhuiyan
3 shared publications
Latest Publications
- Open Access
Hydrogenation Behavior of a Fine-Grained Ti-V-Zr-Nb-Mo-Hf-Ta-W Refractory High-Entropy Alloy Produced by Plasma-Assisted Centrifugal Atomization
In this work, the hydrogenation behavior of a near-equiatomic Ti-V-Zr-Nb-Mo-Hf-Ta-W refractory high-entropy alloy (R-HEA) exposed to pressurized hydrogen has been thoroughly investigated. Isothermal gas-phase hydrogen absorption experiments have been performed and a maximum uptake of 1.13 wt.% H has been achieved after exposure to a pure H2 atmosphere at 350 °C and 60 bar H2 for 6 h. This hydrogen absorption capacity is rather low compared to previous literature, where capacities as high as 2.7 wt.% have been reported. The presence of two distinct (Hf,Zr)-mixed oxides at the surface of the particles has been deduced from X-ray diffraction analyses and identified as the main reason for the relatively low H uptake and the minimal impact onto the mechanical integrity of the R-HEA after hydrogenation. The results hereby reported suggest that R-HEAs containing strong oxide-forming elements such as Hf, Zr, and Ti undergo surface hydrogenation-regeneration upon intermittent exposure to a hydrogen atmosphere. The cyclic nature of such phenomena should be further investigated, as it could lead to the development of novel, self-regenerating protective materials against hydrogen diffusion and embrittlement to be potentially used as permeation barriers.
Open AccessHydrogenation Behavior of a Fine-Grained Ti-V-Zr-Nb-Mo-Hf-Ta-W Refractory High-Entropy Alloy Produced by Plasma-Assisted Centrifugal Atomization
In this work, the hydrogenation behavior of a near-equiatomic Ti-V-Zr-Nb-Mo-Hf-Ta-W refractory high-entropy alloy (R-HEA) exposed to pressurized hydrogen has been thoroughly investigated. Isothermal gas-phase hydrogen absorption experiments have been performed and a maximum uptake of 1.13 wt.% H has been achieved after exposure to a pure H2 atmosphere at 350 °C and 60 bar H2 for 6 h. This hydrogen absorption capacity is rather low compared to previous literature, where capacities as high as 2.7 wt.% have been reported. The presence of two distinct (Hf,Zr)-mixed oxides at the surface of the particles has been deduced from X-ray diffraction analyses and identified as the main reason for the relatively low H uptake and the minimal impact onto the mechanical integrity of the R-HEA after hydrogenation. The results hereby reported suggest that R-HEAs containing strong oxide-forming elements such as Hf, Zr, and Ti undergo surface hydrogenation-regeneration upon intermittent exposure to a hydrogen atmosphere. The cyclic nature of such phenomena should be further investigated, as it could lead to the development of novel, self-regenerating protective materials against hydrogen diffusion and embrittlement to be potentially used as permeation barriers.
- Open Access
- 9 April 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 3640-3649
Role of the microstructure and the residual strains on the mechanical properties of cast tungsten carbide produced by different methods
- 9 April 2024
- Published by Elsevier in Journal of Materials Research and Technology
- Vol. 30, 3640-3649
Open AccessRole of the microstructure and the residual strains on the mechanical properties of cast tungsten carbide produced by different methods
- Open Access
- 1 April 2019
- Published by Elsevier in Microporous and Mesoporous Materials
- Vol. 278, 167-174
Stability of colloidal ZSM-5 catalysts synthesized in fluoride and hydroxide media
- 1 April 2019
- Published by Elsevier in Microporous and Mesoporous Materials
- Vol. 278, 167-174
Open AccessStability of colloidal ZSM-5 catalysts synthesized in fluoride and hydroxide media
- 7 January 2019
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 2 (1) , 334-342
Electronically-Coupled Phase Boundaries in α-Fe2O3/Fe3O4 Nanocomposite Photoanodes for Enhanced Water Oxidation
- 7 January 2019
- Published by American Chemical Society (ACS) in ACS Applied Nano Materials
- Vol. 2 (1) , 334-342
Electronically-Coupled Phase Boundaries in α-Fe2O3/Fe3O4 Nanocomposite Photoanodes for Enhanced Water Oxidation
- Open Access
- 24 April 2018
- Published by MDPI AG in Lubricants
- Vol. 6 (2) , 39
Material Characterization and Influence of Sliding Speed and Pressure on Friction and Wear Behavior of Self-Lubricating Bearing Materials for Hydropower Applications
Nowadays, hydropower plants are forced to have more frequent power control and the self-lubricated bearings used in the applications are one of the most critical components affected by the continuously changing operating conditions. In this study, microstructure and composition of two commercially available bearing materials (Orkot TXM Marine and Thordon ThorPlas) used in hydropower turbines were studied. In addition, the influence of sliding speed and applied pressure on the friction and wear behavior of the materials was investigated systematically for dry sliding conditions. The bearing materials were characterized using X-ray microtomography, Nuclear Magnetic Resonance (NMR) spectroscopy and Inductively Coupled Plasma–Sector Field Mass Spectrometry (ICP-SFMS) techniques. Friction and wear tests were carried out with a polymer pin sliding against a stainless steel (SS2333) plate with a linear reciprocating motion. Test conditions were: room temperature, 9–28 MPa pressure and 10–40 mm/s sliding speed ranges. Surface analysis of the polymer pins and the wear tracks were performed by optical profilometry, Scanning Electron Microscope (SEM) and Energy Dispersive Spectroscopy (EDS) techniques. Test results show that, for both materials, the coefficient of friction (COF) is decreasing at higher pressures. Surface analysis reveals higher concentrations of solid lubricants in the transfer layers formed at higher pressures, explaining the decrease in COF. Furthermore, the specific wear rate coefficients are increasing at higher sliding speeds, especially at lower pressures. Results of this study demonstrate that, under dry sliding conditions, changes in sliding speed and pressure have a significant influence on the tribological behavior of these bearing materials.
- 24 April 2018
- Published by MDPI AG in Lubricants
- Vol. 6 (2) , 39
Open AccessMaterial Characterization and Influence of Sliding Speed and Pressure on Friction and Wear Behavior of Self-Lubricating Bearing Materials for Hydropower Applications
Nowadays, hydropower plants are forced to have more frequent power control and the self-lubricated bearings used in the applications are one of the most critical components affected by the continuously changing operating conditions. In this study, microstructure and composition of two commercially available bearing materials (Orkot TXM Marine and Thordon ThorPlas) used in hydropower turbines were studied. In addition, the influence of sliding speed and applied pressure on the friction and wear behavior of the materials was investigated systematically for dry sliding conditions. The bearing materials were characterized using X-ray microtomography, Nuclear Magnetic Resonance (NMR) spectroscopy and Inductively Coupled Plasma–Sector Field Mass Spectrometry (ICP-SFMS) techniques. Friction and wear tests were carried out with a polymer pin sliding against a stainless steel (SS2333) plate with a linear reciprocating motion. Test conditions were: room temperature, 9–28 MPa pressure and 10–40 mm/s sliding speed ranges. Surface analysis of the polymer pins and the wear tracks were performed by optical profilometry, Scanning Electron Microscope (SEM) and Energy Dispersive Spectroscopy (EDS) techniques. Test results show that, for both materials, the coefficient of friction (COF) is decreasing at higher pressures. Surface analysis reveals higher concentrations of solid lubricants in the transfer layers formed at higher pressures, explaining the decrease in COF. Furthermore, the specific wear rate coefficients are increasing at higher sliding speeds, especially at lower pressures. Results of this study demonstrate that, under dry sliding conditions, changes in sliding speed and pressure have a significant influence on the tribological behavior of these bearing materials.
- 1 April 2018
- Published by Elsevier in Journal of Crystal Growth
- Vol. 487, 57-64
Solution-mediated growth of NBA-ZSM-5 crystals retarded by gel entrapment
- 1 April 2018
- Published by Elsevier in Journal of Crystal Growth
- Vol. 487, 57-64
Solution-mediated growth of NBA-ZSM-5 crystals retarded by gel entrapment
- Open Access
- 7 February 2018
- Published by Springer Nature in Journal of Porous Materials
- Vol. 25 (6) , 1551-1559
Internal structure of a gel leading to NBA-ZSM-5 single crystals
- 7 February 2018
- Published by Springer Nature in Journal of Porous Materials
- Vol. 25 (6) , 1551-1559
Open AccessInternal structure of a gel leading to NBA-ZSM-5 single crystals
- Open Access
- 26 April 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (5) , 433
Formation of Boundary Film from Ionic Liquids Enhanced by Additives
Room temperature ionic liquids (RTILs) have several properties that make them interesting candidates as base fluids for extreme conditions. However, a lack of compatibility with tribo-improving additives combined with an often overly aggressive nature is limiting their use as base fluids. To overcome these drawbacks, hydrocarbon-imitating RTIL base fluids have recently been developed. In this study, the effects of several common additives in the novel RTIL (P-SiSO) were examined by laboratory tribotesting. A reciprocating steel-steel ball-on-flat setup in an air atmosphere was used, where the lubricant performance was evaluated over a range of loads and temperatures. Surface analyses after testing were carried out using optical profilometry, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). Neat P-SiSO displayed high performance in the tribotests. At an elevated load and temperature, a shift in lubrication mode was observed with an accompanying increase in friction and wear. Surface analysis revealed a boundary film rich in Si and O in the primary lubrication mode, while P was detected after a shift to the secondary lubrication mode. An amine additive was effective in reducing wear and friction under harsh conditions. The amine was determined to increase formation of the protective Si–O film, presumably by enhancing the anion activity.
- 26 April 2017
- Published by MDPI AG in Applied Sciences
- Vol. 7 (5) , 433
Open AccessFormation of Boundary Film from Ionic Liquids Enhanced by Additives
Room temperature ionic liquids (RTILs) have several properties that make them interesting candidates as base fluids for extreme conditions. However, a lack of compatibility with tribo-improving additives combined with an often overly aggressive nature is limiting their use as base fluids. To overcome these drawbacks, hydrocarbon-imitating RTIL base fluids have recently been developed. In this study, the effects of several common additives in the novel RTIL (P-SiSO) were examined by laboratory tribotesting. A reciprocating steel-steel ball-on-flat setup in an air atmosphere was used, where the lubricant performance was evaluated over a range of loads and temperatures. Surface analyses after testing were carried out using optical profilometry, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). Neat P-SiSO displayed high performance in the tribotests. At an elevated load and temperature, a shift in lubrication mode was observed with an accompanying increase in friction and wear. Surface analysis revealed a boundary film rich in Si and O in the primary lubrication mode, while P was detected after a shift to the secondary lubrication mode. An amine additive was effective in reducing wear and friction under harsh conditions. The amine was determined to increase formation of the protective Si–O film, presumably by enhancing the anion activity.